Ubiquiti UniFi Manual de usuario
802.11ac Dual-Radio AP
with Public Address System
Model: UAP-AC-EDU
Introduction
Thank you for purchasing the Ubiquiti Networks®
UniFi®802.11ac Dual-Radio AP with Public Address System.
This Quick Start Guide is designed to guide you through
installation and also includes warranty terms.
IMPORTANT: The UAP-AC-EDU requires the UniFi Controller
v
4.9.5
or higher, available at: downloads.ubnt.com/unifi
Package Contents
UniFi AP AC EDU Mounting Template Gigabit PoE* (48V, 0.5A)
with Mounting Bracket
802.11ac Dual-Radio AP
with Public Address System
Model: UAP-AC-EDU
Power Cord* Quick Start Guide
* Included only in the single-pack of the UAP-AC-EDU.
Installation Requirements
• CAT5/6 cable
• Phillips screwdriver
• Drywall or keyhole saw (to cut the hole in the ceiling tile)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, indoor cabling requirements, and Dynamic Frequency Selection
(DFS) requirements.
System Requirements
• Linux, MacOSX, or Microsoft Windows 7/8/10
• Java Runtime Environment 1.6 (1.8 or above recommended)
• Web Browser: Google Chrome (Other browsers may have
limited functionality.)
• UniFi Controller software v4.9.5 or newer (available at:
downloads.ubnt.com/unifi)
Network Topology Requirements
• A DHCP-enabled network (for the AP to obtain an IP address
as well as for the wireless clients after deployment)
• A UniFi Cloud Key or management station running the UniFi
Controller v4.9.5 (or newer) software, located either on-site
and connected to the same Layer-2 network, or off-site in
the cloud or NOC
• For public address system capability: A compatible Android™
or iOS device located on the same Layer-2 network as the
UniFi Controller and UniFi APs
US-16-150W
USG-PRO-4
(DHCP Server)
Internet
UAP-AC-EDU UAP-AC-EDU
LAN
WAN
UniFi Cloud Key
(UniFi Controller)
UAP-AC Outdoor
Remote Access to
UniFi Controller
Sample Network Diagram
All UniFi devices support off-site management controllers.
For setup details, see the User Guide on the website:
documentation.ubnt.com/unifi
Hardware Overview
The UniFi AP AC EDU is comprised of the Speaker Assembly
and UniFi AP.
USB Cable
Speaker
Assembly
UniFi AP
Ethernet Cable
Safety
Wire
Back of the Speaker Assembly
Main Port
Clamp Bracket
Main This Gigabit Ethernet port is used to connect the power
and should be connected to the LAN and DHCP server.
Clamp Bracket The four Clamp Brackets are used to secure the
UniFi AP AC EDU to the ceiling tile.
UniFi AP Ports
Main
Port
Secondary
Port
USB
Port
Reset
Button
Cable Feed
Opening
Secondary Reserved for future use.
Reset The Reset button serves two functions for the UniFi AP:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more than five seconds.
Note: You must remove the UniFi AP from the Speaker
Assembly before you can access the Resetbutton.
Alternatively, the UniFi AP may be reset remotely via a Reset
button located on the bottom of the Gigabit PoE adapter.
Cable Feed Opening The USB and Ethernet cables feed
through this opening.
USB The USB 2.0 port is used to support the Speaker Assembly.
Main This Gigabit Ethernet port is used to carry power
anddata.
LED and Microphone
Microphone
(reserved for
future use)
Color State Status
White Steady Factory default, waiting for
integration.
Flashing Initializing.
White/
Blue Alternating
Device is busy; do not touch or
unplug it. This usually indicates
that a process such as a firmware
upgrade is taking place.
Blue
Steady
Indicates the device has been
successfully integrated into a
network and is working properly.
Quickly
Flashing
This is used to locate an AP.
When you click Locate in the UniFi
Controller software, the LED on the
AP will flash. It will also display the
location of the AP on the map.
Steady with
occasional
flashing
Indicates the device is in an isolated
state (all WLANs are brought down
until an uplink is found).
Hardware Installation
1. Remove the ceiling tile.
2. Remove the backing from the Mounting Template and place
it in the center of the ceiling tile.
242 mm
3. Cut or drill a hole around the template.
4. Rotate the UniFiAP counterclockwise to release it from the
Speaker Assembly.
5. Feed an Ethernet cable through the hole and connect it to
the Main port of the Speaker Assembly.
6. If necessary, lift and rotate the Clamp Brackets so they
remain elevated and tucked against the Speaker Assembly.
Insert the Speaker Assembly into the hole.
7. We strongly recommend that you attach the Safety Wire
(length: 430 mm) to a secure structural point using its clasp
(inside diameter: 14 mm). Do NOT attach the Safety Wire to
a T-bar in the ceiling grid.
Note: It is the installer’s responsibility to verify that
installation complies with local construction and
safety codes.
Two examples are shown below.
8. Tighten the four screws attached to the Clamp Brackets to
secure the Speaker Assembly to the ceiling tile.
9. To connect the cables:
a. Feed the cables of the Speaker Assembly through its
cable slot and the Cable Feed Opening of the UniFi AP.
b. Connect the Ethernet cable to the Main port, and
connect the USB cable to the USB port.
Otros manuales para UniFi
9
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de Ubiquiti
Ubiquiti
Ubiquiti UAP-AC-M Manual de usuario
Ubiquiti
Ubiquiti nano station M Manual de usuario
Ubiquiti
Ubiquiti NBE-M5-16 Manual de usuario
Ubiquiti
Ubiquiti NanoBeam M2 Manual de usuario
Ubiquiti
Ubiquiti GigaBeam Manual de usuario
Ubiquiti
Ubiquiti RP-5AC-Gen2 Manual de usuario
Ubiquiti
Ubiquiti LiteBeam LBE-5AC-LR Manual de usuario
Ubiquiti
Ubiquiti NBE--2AC--13 Manual de usuario
Ubiquiti
Ubiquiti NBE-5AC-Gen2 Manual de usuario
Ubiquiti
Ubiquiti UniFi Wifi BaseStationXG Manual de usuario
Ubiquiti
Ubiquiti U-Installer Manual de usuario
Ubiquiti
Ubiquiti UAP Manual de usuario
Ubiquiti
Ubiquiti UBB Manual de usuario
Ubiquiti
Ubiquiti NBE-5AC-Gen2 Manual de usuario
Ubiquiti
Ubiquiti R5AC-PTP Manual de usuario
Ubiquiti
Ubiquiti UniFi nanoHD AP Manual de usuario
Ubiquiti
Ubiquiti UAP-AC-IW Manual de usuario
Ubiquiti
Ubiquiti airFiber AF-11 Manual de usuario
Ubiquiti
Ubiquiti PBE-M5-300-US Manual de usuario
Ubiquiti
Ubiquiti UniFi AP AC EDU Manual de usuario
