Ubiquiti ER-4 Instrucciones de funcionamiento y mantenimiento

4-Port Gigabit Router

with 1 SFP Port

Model: ER-4

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

EdgeRouter ER-4

Wall Mount Screws

(Qty. 2)

Wall Mount Anchors

(Qty. 2)

Power Cord

installer’s responsibility to follow local country regulations, including operation within legal

frequency channels, output power, indoor cabling requirements, and Dynamic Frequency

Selection (DFS) requirements.

Installation Requirements

• Drill with a 6 mm drill bit (for wall-mounting)

• Phillips screwdriver

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeRouter to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel Ports

Console RJ45 (eth0-eth2) SFP (eth3)

USB

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port,

then you will also need a DB9 adapter.)

Then configure the following settings as

needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

USB Reserved for future use.

RJ45

(eth0-eth2)

RJ45 ports support 10/100/1000 Ethernet

connections.

SFP

(eth3)

SFP port is hot-swappable and supports

Gigabit fiber SFP modules.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter to factory defaults:

• Runtime reset (recommended) The

EdgeRouter should be running after

bootup is complete. Press and hold the

Reset button for about 10seconds until

the LED for port eth3 starts flashing and

then becomes solidly lit. After a few

seconds, the LED will turn off, and the

EdgeRouter will automatically reboot.

• Power-on reset Disconnect the Power

Cord. Press and hold the Reset button

while connecting the power (refer to

“Connecting Power” for details). The

port LEDs will light up in sequential order.

Keep holding the Reset button until the

System LED starts flashing blue and white,

and then release the button.

Front Panel LEDs

System

System LED

Note: The System LED functionality has been updated

with firmware v1.10.7. We recommend that you update

the EdgeRouter to the latest firmware.

State Status

Flashing White Bootup in progress.

White Ready for use, not connected to Ubiquiti®

Network Management System (UNMS™).

Blue Ready for use, connected to UNMS.

Steady Blue

with Occasional

Flashing

Ready for use, unable to connect to

UNMS, check connection to UNMSserver.

Quickly Flashing

Blue Used to locate a device in UNMS.

Alternating

Blue/White Firmware upgrade in progress.

You can use the EdgeRouter Configuration Interface or UNMS

to manage your device. UNMS lets you configure, monitor,

upgrade, and back up your devices using a singleapplication.

Get started at www.unms.com

SFP: Speed/Link/Act

RJ45: Speed/Link/Act

RJ45 LEDs

LED State Status

Speed/

Link/

Activity

Off No Link

Amber Link Established at 10/100 Mbps

Amber

Flashing Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps (1 Gbps)

Green

Flashing Link Activity at 1000 Mbps (1Gbps)

SFP LED

LED State Status

Speed/

Link/

Activity

Off No Link

Green Link Established at 1 Gbps

Green

Flashing Link Activity at 1Gbps

Back Panel

Ventilation Holes Power Grounding Point

Note: There are additional ventilation holes on the sides

of the EdgeRouter.

Hardware Installation

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Wall Mounting

To mount the EdgeRouter on a wall, you will need a drill, a

6mm drill bit, and a Phillips screwdriver.

1. Use a 6 mm drill bit to drill two holes 125 mm apart.

2. Insert the Wall Mount Anchors into the holes. Use a Phillips

screwdriver to secure a Wall Mount Screw to each anchor.

Leave a clearance of approximately 3 mm between each

screw head and its anchor.

125 mm

3 mm

Note: You can also mount the EdgeRouter in a

vertical orientation.

3. Position the EdgeRouter with the Ethernet ports facing

down. Place the wall-mount slots of the EdgeRouter over

the screw heads on the wall. Then slide the EdgeRouter

down to lock it into place.

Grounding the EdgeRouter (Recommended)

The EdgeRouter is grounded through the Power Cord;

however, you can add optional ESD grounding for enhanced

ESD protection.

1. Attach a screw (not included) to secure a ground wire (not

included) to the Grounding Point.

2. Secure the other end of the ground wire to a grounding block.

Connecting Power

1. Connect the Power Cord to the Power port.

2. Connect the other end of the Power Cord to a power outlet.

Using SFP Ports

To use an SFP port:

1. Remove the protective plug covering the SFP port.

2. Plug a fiber SFP module into the SFP port.

1000MbpsSM/SC 20KM DDM

Tx1550nm/Rx1310nm

Otros manuales para ER-4

Tabla de contenidos

Otros manuales de Enrutador de red de Ubiquiti

Ubiquiti

Ubiquiti ER-8-XG Manual de usuario

Ubiquiti

Ubiquiti ToughSwitch Pro TS-80-PRO Manual de usuario

Ubiquiti

Ubiquiti LiteStation2 Manual de usuario

Ubiquiti

Ubiquiti EdgeRouter ER-10X Manual de usuario

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Manual de usuario

Ubiquiti

Ubiquiti edgerouter X SFP Manual de usuario

Ubiquiti

Ubiquiti EdgeRouter X ER-X Manual de usuario

Ubiquiti

Ubiquiti ER-12 Manual de usuario

Ubiquiti

Ubiquiti UFber loco Manual de usuario

Ubiquiti

Ubiquiti UniFi USG Manual de usuario

Ubiquiti

Ubiquiti UDM Manual de usuario

Ubiquiti

Ubiquiti EdgeRouter ER-12P Manual de usuario

Ubiquiti

Ubiquiti UniFi US-24-250W Manual de usuario

Ubiquiti

Ubiquiti UniFi AP PRO Manual de usuario

Ubiquiti

Ubiquiti UFber UF-WIFI Manual de usuario

Ubiquiti

Ubiquiti 3GStation Professional Manual de usuario

Ubiquiti

Ubiquiti Amplifi AFi-LR Manual de usuario

Ubiquiti

Ubiquiti Bullet Manual de usuario

Ubiquiti

Ubiquiti AmpliFi AFi-G Manual de usuario

Ubiquiti

Ubiquiti ER-12 Manual de usuario

Ubiquiti

Ubiquiti TS-8-PRO Manual de usuario

Ubiquiti

Ubiquiti UF-LOCO Manual de usuario

Ubiquiti

Ubiquiti edgepoint r6 Manual de usuario

Ubiquiti

Ubiquiti EdgeRouter LITE Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad