Ubee DVW328 Guía de configuración

Ubee Interactive — www.ubeeinteractive.com

1 Ubee DVW328 – Safety and Installation Product Insert v1.0

DVW328 Advanced Wireless Voice

Gateway - Safety and Installation

Product Insert

Federal Communications Commission

(FCC) Interference Statement

This device has been tested and found to comply

with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable

protection against harmful interference in a

residential installation. This device generates,

uses, and can radiate radio frequency energy. If

not installed and used in accordance with the

instructions, the device may cause harmful

interference to radio communications. There is

no guarantee, however, that interference will not

occur in a particular installation. If the DEVICE

causes harmful interference to radio or television

reception, which can be determined by turning it

off and on, the user can try to correct the

interference by one of the following measures:

•Increase the separation between the DEVICE

and the equipment with which it is interfering

(for example, a television or radio).

•Connect the DEVICE into an electrical outlet

on a different circuit than the interfered device

is connected.

•Consult the dealer or an experienced radio/TV

technician for help.

FCC Regulatory Information

This device complies with Part 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired operation.

There is one statement for this product:

•Only the type of PIFA antenna tested may be

used.

Ubee Interactive — www.ubeeinteractive.com

2 Ubee DVW328 – Safety and Installation Product Insert v1.0

FCC Caution: Any changes or modifications not

expressly approved by the party responsible for

compliance could void the user's authority to

operate this device.

IEEE 802.11b or 802.11g operation of this device

in the U.S.A. is firmware-limited to channels 1

through 11.

For operation within 5.15 ~ 5.35GHz / 5.47

~5.725GHz frequency range, it is restricted to

indoor environment.

FCC Radiation Exposure Statement:

This device complies with FCC radiation

exposure limits set forth for an uncontrolled

environment. This device should be installed and

operated at a minimum distance of 20cm

between itself and your body.

This device must not be co-located or operating

in conjunction with any other antenna or

transmitter.

Safety Notices

Read these instructions carefully before

operating the device. It is important to be aware

of these safety instructions. Install the device

according to these instructions and keep this

guide for future reference.

1. Do not use this device in a humid space, in

the rain, or near splashing water.

2. Do not install during thunder or lightning

storms.

3. Do not cover any ventilation openings in the

device case.

4. Do not place the device near heat sources

such as radiators or stoves.

5. Clean the device only with a clean, dry cloth.

Do not use liquid or chemical cleaners.

6. Avoid static discharge when touching the

device by first touching the coaxial connector

of the coaxial cable.

Ubee Interactive — www.ubeeinteractive.com

3 Ubee DVW328 – Safety and Installation Product Insert v1.0

7. Installation of the device should include

grounding the coaxial cable to the earth at the

building entrance per ANSI/NFPA 70 and the

National Electrical Code (NEC, in particular,

Section 820.93, Grounding of the Outer

Conductive Shield of a Coaxial Cable). The

device is designed for IT power systems with

phase-to-phase voltage at 120V.

8. Disconnecting the Device: If the device

becomes damaged or encounters some other

abnormality, disconnect the power plug from

the AC wall outlet immediately.

9. The device should be installed in a location

not to exceed the maximum temperature of

40 degrees Celsius (104 degrees

Fahrenheit).

10. When this device is placed upright with the

aid of the stand, the stand must be fixed at a

90-degree angle to the device. Otherwise, the

device will have the risk of tipping over.

Installation

To install this device, follow the procedures

below and refer to the following page for a

connection diagram.

1. Connect one end of a coaxial cable (not

included) to the CABLE port on the device.

Connect the other end to a cable splitter or the

cable wall outlet. Be sure not to bend or over

tighten the cables as this may strain the

connector and cause damage. If you plan to

connect the device and a television to the

same cable wall outlet, you must use a cable

line splitter (not included).

2. Connect one end of the supplied Ethernet

cable to one of the ETHERNET ports (ETH1

to ETH4) on the device. Connect the other

end to the ETHERNET port on a PC. Note:

Category 5e or Category 6 Ethernet cables

with RJ-45 connectors must be used when

connecting Ethernet devices to the LAN ports.

This ensures Gigabit Ethernet speeds (unless

the computer does not support it).

Ubee Interactive — www.ubeeinteractive.com

4 Ubee DVW328 – Safety and Installation Product Insert v1.0

3. Connect one end of an RJ11 phone cable to

one of the TEL ports on the modem (that has

been provisioned for voice service as

specified by the service provider), and

connect the other end to the phone port of the

telephone. Note: If voice service is not

provisioned through the service provider,

telephone service is not available.

4. Connect the power cord to the POWER port

on the device. Plug the other end of the power

cord into the AC wall outlet. Important: Use

only the power cord that is shipped with the

device.

Ubee Interactive — www.ubeeinteractive.com

5 Ubee DVW328 – Safety and Installation Product Insert v1.0

Wall-Mount Installation

You can mount the device on a wall using the 2

mounting brackets on the bottom of the device.

We recommend that you use two round or pan

head screws.

1. Install two screws horizontally apart on a wall

using the measurement shown to the right.

The screws should protrude from the wall so

that you can fit the device between the head

of the screw and the wall. If you install the

screws in drywall, use hollow wall anchors to

ensure that the unit does not pull away from

the wall due to prolonged strain from the cable

and power connectors.

2. Remove the device from the product package.

3. Mount the device on the wall.

4. Refer to the following figure.

The Distance of the Pothook (Horizontal)

The Screw’s Size (mm)

148mm (5.75 inches)

6.65+/-0.35

1.9+/-0.15

19.0+/1.20

Ubee Interactive — www.ubeeinteractive.com

6 Ubee DVW328 – Safety and Installation Product Insert v1.0

Additional Information

1. RESET Button (back of device): This button

resets the device to factory defaults. Using a

pointed object, insert it into the button opening,

and hold for more than 10 seconds. The

device will reset and reboot. Note: Not all

parameters are reset to factory defaults. Refer

to the User Guide for more information.

2. WPS button (top of device): The WPS button

is used for the Wi-Fi Protected Setup (WPS)

method to connect a Wi-Fi device to the

DEVICE. Refer to the User Manual for more

information.

3. USB Connector (back of device): USB devices

can be connected here, such as flash drives,

external HDDS, printers, etc.

LEDs and Other Device Indicators

See the following diagram and descriptions of the

device’s LED behavior, and the behavior of the

back-panel Ethernet indicators.

LED Indicators (Color = Blue When On):

POWER—If On, indicates that the device has

successfully completed internal power-on tests.

LED flashes if power-on fails. Note that the LED

flashes briefly immediately after powering the

device.

DS/US—When the device initializes, the LED

flashes. When the device locks on to channels

and registers OK, the LED is On. When the

device performs a firmware upgrade, the LED

flashes.

ONLINE—When the device is obtaining an IP

address and configuration file, the LED flashes.

When device obtains these items, the LED is On.

Ubee Interactive — www.ubeeinteractive.com

7 Ubee DVW328 – Safety and Installation Product Insert v1.0

2.4G—When 2.4G Wi-Fi is enabled, the LED is

On. When 2.4G Wi-Fi is disabled, the LED is Off.

5G—When 5G Wi-Fi is enabled, the LED is On.

When 5G Wi-Fi is disabled, the LED is Off.

TEL1 and TEL2—The LED is On when a

telephone is on-hook. The LED flashes when a

telephone is off-hook.

BATTERY—The LED is On when the battery is

installed and is charged. The LED is Off if no

battery is installed.

WPS (top of device)—If not used, the LED is Off.

When the user pushes the WPS button or

triggers WPS via the device’s web GUI, the LED

flashes white for 4 minutes until a PIN is entered

from a wireless client that wishes to connect.

After a Wi-Fi client attaches successfully, the

LED remains solid white for 5 minutes, and then

turns off.

Back Panel Ethernet Indicators

(Color = Orange or Green):

•When an Ethernet device, such as a computer,

is connected to the device, the LED is Green

when connected at 10/100 Mbps speeds.

•When an Ethernet device, such as a computer,

is connected to the device, the LED is Orange

when connected at 1000 Mbps speeds

(Gigabit Ethernet).

•When data is being passed between the

device and the connected device, the LED

flashes.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Puerta de Ubee

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario