U-Line H-2590 Manual de usuario

0810 IH-2590PAGE 1 OF 3

1-800-295-5510

uline.com

HEAVY DUTY AUTOMATIC

TAPE DISPENSER

H-2590

1. When using automatic feed, remove the first piece

of tape. The unit will automatically feed and cut the

next piece at the preset length.

2. Feed length can be easily set using thumbwheel

controls.

3. Hold down shaft increases accuracy by maximizing

tape adhesion to the feed rollers.

4. The blade is easy to remove and replace.

5. Optional serrated blade for hard to cut materials.

6. Tape Length Display – Shows preset feed length.

Four-digit display can be set from 50-9999mm

(2" - 393").

7. Interval Knob – Sets delay time before dispensing

next piece.

8. Auto/Manual Switch – Toggles operating mode

between manual (press tape advance button

to dispense) and auto (automatic feed and cut

when piece is removed).

9. Power Switch – Press to turn power on and off.

10. Tape Advance Button – Press to feed and cut one

piece of tape to the preset length.

11. Hold Down Shaft – Increases adhesion to feed roller.

12. Reel Holder – 3" core to hold material.

13. Alarm – Lights when there is a malfunction in the unit.

FEATURES

REEL HOLDER

TAPE ADVANCE BUTTON

POWER SWITCH

ALARM

HOLD DOWN SHAFT

(UNDER TOP COVER)

MODE SELECTION

(MANUAL, AUTO & INTERVAL)

TAPE LENGTH DISPLAY

INTERVAL KNOB

0810 IH-2590PAGE 2 OF 3

1. After tape has been loaded and fed, turn power

switch off.

2. Set tape length display to required length using the

push buttons above and below the

numerical display.

NOTE: The length shown is in millimeters.

3. Flip auto/manual switch to desired location.

4. AUTO: When the cut piece of tape is removed from

the machine, the next piece is automatically fed

and cut. The interval knob will set the time delay

before the next piece is dispensed. Maximum delay

is 25 seconds.

5. MANUAL: The tape advance button must be pressed

each time a piece of tape is needed.

6. The tape will then be fed and cut.

7. Turn power switch on.

8. Press tape advance button to begin dispensing

tape.

NOTE: Tape lengths vary depending on

material. Verify length of first piece.

1. With power switch off, plug power cord into

dispenser and then into wall outlet.

2. Make sure machine is grounded properly.

3. Set the tape length display to 200mm.

4. Set the auto/manual switch to manual.

5. Turn dispenser power switch on, switch will be

illuminated.

6. Place tape roll on reel holder.

7. Put reel holder into reel holder slots.

8. Open latched top cover and remove metal hold

down shaft.

9. Press end of tape firmly onto metal feed roller, then

replace hold down shaft over tape and close top

cover.

10. Press tape advance button.

11. Remove tape then press tape advance button

again to ensure proper feeding.

SET-UP

OPERATION

SPECIFICATIONS

MODEL

TAPE

WIDTH

CUT

LENGTH

MAX.

OUTSIDE

DIAMETER

CORE

DIAMETER**

ACCURACY

OF CUT

TAPE

CUTTER

FEED

TYPE

LENGTH

SETTING WEIGHT DIMENSIONS

TDA080 .25 to 3.15"

(6.4 to 8.0mm)

2 to 394"

(50 to 9999mm)

(251mm)

(76.2mm)

+/- 0.4"

(1mm) Automatic Automatic Digital 21lbs.

(9.5kg)

9"(L) x 6.625"(W) x 12"(H) /

229mm(L) x 168mm(W) x 305(H)

• Auxiliary stand available for diameters up to 24”.

* Dependent on material.

** Other sizes available.

0810 IH-2590PAGE 3 OF 3

When problems occur, carry out the following procedures. If the tape dispenser does not operate normally after

following the troubleshooting procedures, contact your supplier.

WEEKLY

Wipe feed rollers and blade with proper solvent to

remove adhesive build-up.

MONTHLY

Apply silicone oil to #242 blade roller. Inspect pressure

rollers and cutting blade for wear.

TROUBLESHOOTING

MAINTENANCE

OPERATING ISSUE RECOMMENDATIONS

No power light / tape does not feed. Unplug unit and plug in again.

Turn power switch off, wait 5 seconds, turn unit back on.

Check that front panel is closed securely, and safety

interlock is engaged.

Verify that the fuse has not blown.

Check that Tape Length Display is 40mm or greater.

Tape does not feed when unit is in

auto mode.

Check that Auto/Manual Switch is in correct position.

Turn Interval Knob all the way counterclockwise.

Wait 1 full second after tape is cut before removing

tape from machine.

Blade sticks in closed position Apply silicon oil to #242 Blade Roller.

CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA

Este manual sirve para los siguientes modelos

Otros manuales de Dispensador de U-Line

U-Line

U-Line TORK PEAKSERVE H-9385 Manual de usuario

U-Line

U-Line TORK XPRESS H-1595 Manual de usuario

U-Line

U-Line UCDE215 Manual de instalación

U-Line

U-Line GOJO LTX H-5066 Manual de usuario

U-Line

U-Line SOFPULL H-2861 Manual de usuario

U-Line

U-Line Boraxo H-3884 Manual de usuario

U-Line

U-Line H-6087 Manual de usuario

U-Line

U-Line H-1119 Manual de usuario

U-Line

U-Line TORK MATIC H-9952 Manual de usuario

U-Line

U-Line H-2546 Manual de usuario

U-Line

U-Line H-16 Manual de usuario

U-Line

U-Line Marsh H-1358 Manual

U-Line

U-Line H-2557 Manual de usuario

U-Line

U-Line H-8883 Manual de usuario

U-Line

U-Line FENDALL 2000 Manual de usuario

U-Line

U-Line SOFPULL H-2861 Manual de usuario

U-Line

U-Line PURELL ES6 Manual de usuario

U-Line

U-Line IH-99 Manual de usuario

U-Line

U-Line H-4017 Manual de usuario

U-Line

U-Line H-1130 Manual de usuario

U-Line

U-Line Econodot H-2930 Manual de usuario

U-Line

U-Line TORK H-7544 Manual de usuario

U-Line

U-Line SLIMFOLD H-4701 Manual de usuario

U-Line

U-Line H-725 Manual de usuario

Manuales populares de Dispensador de otras marcas

Silver King

Silver King Majestic SK12MAJ Guía de inicio rápido

Franke

Franke F3Dn Twin Manual de usuario

STIEBEL ELTRON

STIEBEL ELTRON UltraHot Plus Manual de usuario

DAN DRYER

DAN DRYER 282 Manual de usuario

Essity

Essity Tork 473208 Manual de usuario

CBS

CBS SD300BU-88 Guía de configuración

Sealey

Sealey MK77 Manual de usuario

Fluid Management

Fluid Management Accutinter 1600 Manual de usuario

Franke

Franke DVS SD99-010 Manual de usuario

Graco

Graco Dispensit 1053-10C Guía de solución de problemas

ITALTINTO

ITALTINTO i50 Manual de usuario

Coca-Cola

Coca-Cola FREESTYLE 9000 Manual de usuario

Graco

Graco ProMix 2KE Manual de instrucciones

TECHCON SYSTEMS

TECHCON SYSTEMS TS1251 Manual de usuario

Wayne

Wayne GLOBAL VISTA CNG Manual de usuario

clarsen

clarsen H133 Manual de usuario

PicoBrew

PicoBrew Zymatic Manual de usuario

BOWMAN

BOWMAN BP-007 Manual de usuario