Tycon Power Systems TP-SW8(-NC) Manual de usuario

TYCON POWER SYSTEMS

TP-SW8(-NC)

8 port PoE Endspan (Switch)

(Extend Ethernet and PoE)

USER’S MANUAL

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

1. General Information..............................................................

2. Hardware Description...........................................................

LED Indicators.......................................................................................

Power Wiring ........................................................................................

Ethernet Port /PD Port Wiring …………................................................

3.Network Application……........................................................

4.Model information………….………........................................

5.Technical Specification………...............................................

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

1. General Information

The TP-SW8 POE Switch family provides a PoE/Data input port that is compatible with 802.3af

and 802.3at (Type 1 and Type 2) and it has seven 10M/100M TX ports with PoE PSE function. In

addition to the ability to accept standard 48VDC power on the Ethernet input Port 8, the

TP-SW8(-NC) provides 2 secondary DC wire terminal input ports for PoE switch operation from

12VDC to 58VDC. PoE output voltage is equal to the input voltage, making this switch as universal

voltage PoE switch. The PoE Switch can be used as an Ethernet/PoE repeater to extend Ethernet

data and DC power up to 200 meters.

This manual will help you install and maintain the PoE switch.

Installation of the PoE switch is very easy and you will begin to operate as soon as you are powered

up. The TP-SW8 comes with DIN rail mounting clips for ease of mounting in network cabinets.

2. Hardware Description

*LED Indicator

There are 18 LEDs on the PoE switch to indicate the power and operational status. The following

section describes the functions of each LED indicator.

Front panel detail

the port number is as the diagram shows.

5 6 7 8

1 2 3 4

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

*PWR Indicator

LED

STATUS

Description

Power

Green

LED ON if power input has valid power

supplied. (via the terminal block on rear

panel or Port 8 on front panel)

Red

LED ON if the following condition

happens.

*Power input under voltage (Vin<12V)

*Power input over voltage (Vin>58V)

*PoE over current(2A)

The indicator is used on TP-SW8

Off No power in DC input

*SWITCH indicator (the right LED on RJ45)

LED STATUS Description

P1~P8

Link/Act

Green

A network device is detected at 100Mbps,

but no communication activity is detected.

Green

Blinking

This port is transmitting to, or receiving

package from another device at 100Mbps.

Yellow A network device is detected at 10Mbps,

but no communication activity is detected.

Yellow

Blinking

This port is transmitting to, or receiving

package from another device at 10Mbps.

Off No device is detected.

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

*PoE indicator (the left LED on RJ45)

LED STATUS Description

P1~P7

PoE PSE

Yellow

LED ON when PoE power output.

Off No PoE output

PoE PD

Yellow

TP-SW8:4 pairs power source receive.

TP-SW8-NC:2 or 4 pairs power source

receive.

Yellow

Blinking

TP-SW8:2 pairs power source receive.

TP-SW8-NC:unused.

Off No power is detected on this port.

*Power wiring

The PoE switch accepts input voltage from terminal block (rear panel) or RJ45 cable (port 8). If

power input from terminal block, the input voltage must be in the range of 12 to 57 VDC. Input

current on secondary wire terminal input is 10A max. Input current on port 8 is 2A max.

If power input from the RJ45 cable (port8) in the TP-SW8, the input voltage must be in the range of

44 to 57VDC if running for 802.3af operation or 50 to 57VDC if running for 802.3at operation.

If the TP-SW8 is not powered within IEEE802.3af/at specification, it will only function as an

ethernet switch without PoE output.

The PoE PSE ports will deliver DC power over the spare pairs as the connection:

* TX on lines 1 and 2

* RX on lines 3 and 6

* V+ on line 4 and 5

* V- on line 7 and 8

The Port 8 may get power over the signal pair or spare pairs, the connection as:

* Data pair A plus V+ /V- on lines 1 and 2

* Data pair B plus V-/V+ on lines 3 and 6

* V+/V- on line 4 and 5

* V-/V+ on line 7 and 8

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

Rear panel terminal block wiring detail:

You may use the TP-SW8 with our AC adaptor products as the below: (OPTION)

PSHP-18 PSHP-24 PSHP-48

Maximum output 18VDC/7.5A 24VDC/6.25A 48VDC/3.125A

Related model TP-SW8-NC TP-SW8-NC TP-SW8

TP-SW8-NC

*Ethernet Port/PD Port Wiring

The PoE Switch supports Port 1 to Port 8 with automatic MDI/MDI-X crossover, autosense of the

speed and duplex for 10Base-T or 100Base-TX connections. Automatic MDI/MDI-X crossover

allows you to connect to other devices (switches, hubs, or workstations etc..), without regard to

using straight-through or crossover cabling.

Port 1 to port 7 also provides PSE function which delivers DC power through the spare pairs (pair

4,5 and pair7,8) to the PD. Port 8 provides PD function that receive power from 4 pairs or 2 pairs

Ethernet cable.

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

The following tables depict the wiring diagram of straight-through and crossover cabling. The

crossover cables simply cross-connect the transmit lines at each end to the receive lines at the

opposite end.

Straight-through Cabling

Pin 1 Pin 1

Pin 2 Pin 2

Pin 3 Pin 3

Pin 6 Pin 6

Cross-over Cabling

Pin 1 Pin 3

Pin 2 Pin 6

Pin 3 Pin 1

Pin 6 Pin 2

Connect an Ethernet cable into any switch port and connect the other side to your attached device.

The green or yellow Link/Act LED will light up when the cable is correctly connected. Refer to the

LED Indicator section for descriptions of each LED indicator.

If a port LED is off, go back and check for connectivity problems between that port and the network

device it is connected to.

The maximum cable length for 10/100BaseT with Cat 5 twisted pair cables is typically 100 meters

(328 ft.).

3. Network Application

The PoE Switch can receive power from PoE midspan and provide power to the PD. It will power

802.3af compliant devices if it is powered at 48VDC although it will not perform the 802.3af

handshake with the client device. The PoE Switch can be installed in a more appropriate position

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

for better performance to extend Ethernet to 200 meters. The following figure is an example of a

network application for PoE Switch.

(TP-SW8-NC added the repeater function since S/N 127000375A)

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

3. Model Information

Model Input Voltage

(REAR) Input Voltage

(Port 8) Output voltage

802.3af/at

TP-SW8-NC 12-57VDC 12-57VDC 12-57VDC

(non-regulated) No

TP-SW8 40-57VDC 42.5-57VDC

40-57VDC

(High voltage

output,

non-regulated)

Yes

4. Technical Specifications

Standards IEEE802.3/IEEE802.3u standards (10 base-T/100base-T)

Ports 8 ports with 7 PoE PSE & 1 PoE PD, supports auto-crossover &

auto-polarity

Transmission speed 100 Mbps(100base-T),10 Mbps(10base-T) Auto-negotiation

Switch technology store-and-forward

Protocols CSMA/CD

Flow control IEEE802.3x(full-duplex),back pressure(half-duplex)

Data transmission rate 148800pps for 100base-T, 14880pps for 10base-T

Address table 2K MAC address table, self-learning

Connect RJ-45

PoE port Port 1-7, Pin assignment: TX(1,2), RX(3,6), V+(4,5), V-(7,8)

Port 8, 4 pairs PD

User’s Manual

TP-SW8

TYCON POWER SYSTEMS

Maximum PoE power Port 1-7: IEEE802.3af –16.8W

IEEE802.3at—35W

2 A per port , total 7A Maximum

Port 8: 90W (802.3at 2 event classification)

PoE disconnect mode DC disconnect

PoE auto detection IEEE802.3af and IEEE802.3at(2 event classification)

PoE protection Over-current, over/under voltage

LEDs *Link/Activity (Green ON/ Green Blinking @100Mbps/

Yellow/Yellow Blinking @10Mbps)

*PoE (Yellow) port 1-7 ON - PD detect

Port 8 TP-SW8:ON – 4 pair power,

Blinking-2 pair power

TP-SW8-NC:ON – 2 or 4 pair power

*POWER Green-normal, Red-alarm

Power input DC(12V~57V) from rear panel or DC(44V~57V) from port 8 from

midspan (or network switch)

Power consumption 5W without PD loading

Input Voltage Input Current

12V 0.058A

24V 0.037A

48V 0.032A

56V 0.032A

Operating temperature

-40℃~ +85℃

Operation humidity 90% relative humidity, non-condensing

Storage temperature

-40℃~+85℃

Dimension 40mm(H)x118mm(W)x159mm(D) DIN rail mountable

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Tycon Power Systems

Tycon Power Systems

Tycon Power Systems TP-MS4x4 Manual de usuario

Tycon Power Systems

Tycon Power Systems TP-SW5G-MULTI Manual de usuario

Tycon Power Systems

Tycon Power Systems TP-SW5G-NC Manual de usuario

Tycon Power Systems

Tycon Power Systems TP-SW5GNC-OUT Manual de usuario

Tycon Power Systems

Tycon Power Systems TP-SW5G Manual de usuario

Tycon Power Systems

Tycon Power Systems TP-SW8GAT/24-SFP Manual de usuario

Tycon Power Systems

Tycon Power Systems TP-SSW5(-NC) Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario