Tyco CCU/232-NIM Guía de configuración

1 of 6 REF: CCU232-NIM.DOC REV: B August 6, 1998

Southgate Corporate Park

CANNON HILL 4170

AUSTRALIA

Tel: +61 7 3318 6900

Fax: +61 7 3318 6905

CCU/232-NIM Install Instructions Part #: CCU/232-NIM

This equipment is designed to be installed and serviced by fully qualified field engineers. No user

serviceable or installation parts inside.

Supplied:

1 x CCU/232 board with firmware for NIM (FSI) Interface

1 x Mounting Bracket

1 x Power connector for CCU/232

1 x Supervision relay connector for CCU/232

You will need:

1 x cable from MXL-CZM (24V) & Batt. to CCU/232. Connector supplied.

1 x interface cable from NIM-1R to CCU/232 (see later for wiring information)

1 x (Optional) MXL-MPFO Adaptor plate (MXL installations)

Power Requirements:

Typical: 200mA at 24VDC

Voltage Input: 20-30 VDC

Installation of CCU/232 (MXL Fire indicator Panel):

2 of 6 REF: CCU232-NIM.DOC REV: B August 6, 1998

TB5 Pin 12

CZM-1 Pwr

TB5 Pin 10

P2 Battery

+MMB-1

BATTERY BATTERY

-+-+

CHN_B

CHN_A

BAT+

COM-

24V+

CCU/232

CHN_C

RELAY

NIM-1R

13 14 16 12

Programming

Laptop

CCU/232 Mounting Bracket

MXL-MPFO (or SYS3-MPFO) Adaptor Plate

CHN_C

The CCU/232 is designed to mount on the MXL-MPFO adaptor plate for the MOM-4 position,

occupying one D2300CP position (MXL Only). CCU/232 can also mount to SYS3-MPFO adaptor

plate for System 3 enclosure (EA-31, EA-32, EA-35) mounting.

•Connect D9 port CHN_C of CCU/232 to NIM-1R using the following connection diagram.

CCU/M 232-C 9PIN (DTE)

NIM-1R (MOM4)

2 13

3 14

5 16

8 12

•A PC can be temporarily connected to port CHN_C of CCU/232 for programming of CCU/232.

Note that this is a straight through standard RS232 cable for laptops.

CCU/232 CHN_C

9PIN (DCE) PC/LAPTOP

25PIN PC/LAPTOP

9PIN

2 3 2

3 2 3

4 20 4

5 7 5

•If hardware supervision is required connect the relay output from the CCU/232 to a suitable input on

the MXL (software supervision does not require this). There are two relay sockets located next to

the D9 connector -these are IDENTICAL and either can be used. The relays will Energise when

Supervision failure is detected.

•Connect the 24V DC power source (CZM or plug pack) to the supplied connector. The power

connector is next to the CHN_C port. Pin connections are:

PWR (+24VDC) RETURN/COM(0V) BATTERY(24V)

These connections are written on the board. On an MXL,

3 of 6 REF: CCU232-NIM.DOC REV: B August 6, 1998

MXL CCU/232

TB5 (CZM) Pin 12 24V

TB5 (CZM) Pin 10 COM

Battery 24V BAT

Operation of LEDs:

•Each port has a Green and a Yellow LED. Green means the port is operating OK. Yellow means that

the port is not operating OK, or there has been supervision failure on this port.

4 of 6 REF: CCU232-NIM.DOC REV: B August 6, 1998

Connecting CCU/232 RS232 Ports A and B to the CCU network:

•First Determine which two ports you are connecting using the following table:

CCU BOARD PORT A PORT B PORTC

CCU/232 DTE DTE DCE

CCU/M DCE DTE DTE

CCU/F

CCU/422 n/a n/a DCE

•Connecting a DTE to DCE uses a straight through cable. Connecting a DTE-DTE or DCE-DCE

requires a null modem cable (pins 2 and 3 swapped on a D9 connector).

•If you are connecting to a PC COM port then this is a DTE port.

CCU/232

9PIN (DTE)

DCE port of a

CCU Board DTE Port of a

CCU Board PC COM

25PIN

(DTE)

PC COM

9PIN

(DTE)

2 2 3 2 3

3 3 2 3 2

5 5 5 7 5

5 of 6 REF: CCU232-NIM.DOC REV: B August 6, 1998

Configuration of CCU/232:

•If your network has less than 256 CCU nodes, you can use the jumpers (IN1 to IN8) on the

CCU/232 to configure the CCU Network address. Each CCU Node must have a unique address.

Address 0 CANNOT BE USED. The jumpers represent a BINARY address. Example:

Addr IN8 IN7 IN6 IN5 IN4 IN3 IN2 IN1

1 SHORT

2 SHORT

3 SHORT SHORT

4 SHORT

5 SHORT SHORT

6 SHORT SHORT

7 SHORT SHORT SHORT

8 SHORT

9 SHORT SHORT

10 SHORT SHORT

11 SHORT SHORT SHORT

12 SHORT SHORT

13 SHORT SHORT SHORT

14 SHORT SHORT SHORT

15 SHORT SHORT SHORT SHORT

16 SHORT

255 SHORT SHORT SHORT SHORT SHORT SHORT SHORT SHORT

•If you need to use the jumpers as supervised inputs, or you need to program addresses from 256 to

65535 (The CCU Network does not support more than 65535 nodes). You will need to use a

laptop to program the network address.

•Software configuration requires that a laptop be connected to port CHN-C using a straight through

RS232 cable. A terminal program (such as Procom/Telix or Windows Terminal using VT100

emulation) can be used with communication parameters set to 9600,N,8,1. Power up the CCU.

After approximately 3 seconds, all LEDS on the CCU will indicate. BEFORE this happens you can

type MENU, allowing programming of the CCU/232 using the default configuration.

•Type MENUto invoke the programming menu. There is no need to press <Enter>.

•Follow the menu options (detailed instructions follow) and set the:

ADDRESS -Addresses from 1 to 65535 can be used.

INPUTS -Specify whether you want to use the jumpers for the address (or the internal

address).The CCU/232 is supplied with factory setting using the JUMPERS. So, on smaller

networks there is no need to connect a laptop.

•Jumpers MODA, MODB and RSTshould have no jumpers connected.

6 of 6 REF: CCU232-NIM.DOC REV: B August 6, 1998

Configuration of NIM-1R:

The NIM-1R must be programmed as an FSI. Consult the NIM-1R installation sheet for

instructions on setting dip switches.

Using CSGM, the NIM-1R(FSI) Should be set for the following communications options:

FSI

Supervised Operation

9600 Baud

7 bits

EVEN Parity (NOTE: The CSGM parity setting must be EVEN)

1 stop bit

Make sure you give this NIM a panel address.

If you require commands to be sent to this panel. Example by an operator using XL Graphics on

the CCU-NET, then you must allow the NIM to accept commands. This can only be done by

logging onto CSGM using the ‘PASSWORD OF THE DAY’. Detail for the NIM will then allow

commands to be enabled.

1 2 3 4

4321

0 0

B2-CCU3/M 130-May-1997H:\CCU\V3A422\PCB\V1\WIRING10.SC

Title

Size: PCBRef: Date:File: Revision: Sheet of

CCU-Net base23/28 Pritchard Road, Virginia

Queensland, Australia, 4014

Ph:+61-7-38653777

Fax:+61-7-38653778

CCU-Net ( A data collection , transportation and control network)

Connecting a CCU/232 network card to an MXL Fire Panel via MOM4 card (NIM interface) using RS232.

Screw

Terminals

1 2 3 4 5 6 7 8 9 10111213141516

TB4

1 2 3 4 5 6 7 8 910111213141516

TB3

1 2 3 4 5 6 7 8 910111213141516

TB1

1 2 3 4 5 6 7 8 9 10111213141516

TB2

MOM4

MXL Fire Panel

OUT

GND

CTS

RTS

DSR

GND

DTR

TXD

RXD

DCD

DCE AT CCU

OUT

OUT 1

CHN_C

RS232

RS232 Connection

PCB ID: B2-CCU232A

CCU/232 RS232 Networked Communications

Power Connector

Supervisory Relay Connection.232 Chn A

232 Chn B

DB9 Plug

Preferably less than 30 metres.

Tabla de contenidos

Otros manuales de Unidad de control de Tyco

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario