Tyco Fire Product Gem F917 Manual de usuario

INTERMEDIATE LEVEL SPRINKLERS

MODEL F917

STANDARD RESPONSE, SOLDER TYPE, 8.0 K-FACTOR, 3/4" NPT**

GENERAL DESCRIPTION

The 8.0 K-Factor Model F917 Interme-

diate Level Sprinklers (Ref. Figure A)

are automatic sprinklers of the “stand-

ard response” fusible solder type.

They are intended for use in fire sprin-

kler systems designed in accordance

with the standard installation rules rec-

ognized by the applicable Listing or

Approval agency (e.g., UL Listing is

based on NFPA requirements). Both

the Pendent and Upright Sprinklers

produce a hemispherical water distri-

bution pattern below the deflector.

Intermediate Level Sprinklers are pri-

marily designed for use in rack storage

sprinkler systems, where their ther-

mally sensitive elements must be

shielded from the water spray of higher

elevation sprinklers which could oper-

ate earlier during a fire. Intermediate

Level Sprinklers are also used in appli-

cations such as beneath open gridded

catwalks.

APPROVALS AND STANDARDS

Laboratory listings and approvals for

the 8.0 K-Factor Model F917 Interme-

diate Level Sprinklers are given in Ta-

ble A.

WARNING

The 8.0 K-Factor Model F917 Inter-

mediate Level Sprinklers described

herein must be installed and main-

tained in compliance with this docu-

ment,aswellasapplicablestandards

of the National Fire Protection Asso-

ciation, in addition to the standards

of any other authorities having juris-

diction. Failure to do so may impair

the integrity of these devices.

The owner is responsible for main-

taining their fire protection system

and devices in proper operating con-

dition. The installing contractor or

manufacturer should be contacted

relative to any questions.

TECHNICAL DATA

The 8.0 K-Factor Model F917 Interme-

diate Level Sprinklers are rated for use

at a maximum service pressure of 175

psi (12,1 bar) and they are available in

the temperature ratings and finishes

indicated in Table A.

The flow “Q” in GPM (LPM) is deter-

mined by the following formula:

where the nominal discharge coeffi-

cient “K” equals 8.0 (115,2) and “p”

equals the residual flowing pressure in

psi (bar).

The Model F917 Intermediate Level

Sprinklers are obtained by assembling

a 3 inch ( 76,2 mm) O.D. brass Shield

to the 8.0 K-Factor Model F916 Pen-

dent or Upright Sprinklers described in

Technical Data Sheet TD527H. In the

case of the pendent sprinkler, field as-

sembly of the shield is required, and in

the case of the upright sprinkler, the

shield is factory assembled to the

sprinkler.

QKp

Printed in U.S.A. 3-01 TD503H

FIGURE A

8.0 K-FACTOR MODEL F917 (SIN G3102) PENDENT AND (SIN G3153) UPRIGHT

INTERMEDIATE LEVEL SPRINKLERS

*Temperature rating is indicated on the Deflector.

** Pipe thread connections per ISO 7/1 can be provided on special request.

TYCO FIRE PRODUCTS, 7071 S. 13th Street, Suite 103 Oak Creek, WI 53154 — www.gemsprinkler.com

Customer Service/Sales: Tel: (877) 436-8926 / Fax: (877) 866-9250

Technical Services: Tel: (800) 381-9312 / Fax: (800) 791-5500

OBSOLETE

INSTALLATION

NOTES

A leak tight 3/4 inch NPT sprinkler

joint should be obtained with a torque

of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). A

maximum of 30 ft. lbs. (40,7 Nm) of

torque is to be used to install sprin-

klers with 3/4 inch NPT connections.

Higher levels of torque may distort the

sprinkler inlet with consequent leak-

age or impairment of the sprinkler.

— Upright Sprinklers—

The Model F917 Intermediate Level

Upright Sprinklers must be installed in

accordance with the following instruc-

tions.

1. With pipe thread sealant applied,

hand tighten the sprinkler into the

sprinkler fitting.

2. Tighten the sprinkler into the sprin-

kler fitting using only the W-Type 9

Sprinkler Wrench (Ref. Figure B).

The wrench is to be applied to the

sprinkler wrenching area shown in

Figure A.

— Pendent Sprinklers—

The Model F917 Intermediate Level

Pendent Sprinklers must be installed

in accordance with the following in-

structions.

1. Roll one of the two required O-Rings

over the sprinkler threads until it

seats against the sprinkler wrench-

ing area flange as shown in Figure

2. Install the Shield over the sprinkler

threads, and then roll the second

O-Ring over the sprinkler threads

until it is seated firmly against the

Shield.

3. With pipe thread sealant applied,

hand tighten the sprinkler into the

sprinkler fitting.

4. Tighten the sprinkler into the sprin-

kler fitting using only the W-Type 9

Sprinkler Wrench (Ref. Figure B).

The wrench is to be applied to the

sprinkler wrenching area shown in

Figure A.

When installed correctly, the O-

Rings will be slightly compressed

and the Shield will be held firmly in

place.

CARE AND MAINTENANCE

The Model F917 Intermediate level

Sprinklers must be maintained and

serviced in accordance with the follow-

ing instructions:

NOTE

Before closing a fire protection system

main control valve for maintenance

work on the fire protection system

which it controls, permission to shut

down the affected fire protection sys-

tem must be obtained from the proper

authorities and all personnel who

may be affected by this action must be

notified.

Sprinklers which are found to be leak-

ing or exhibiting visible signs of corro-

sion must be replaced.

Automatic sprinklers must never be

shipped or stored where their tempera-

tures will exceed 100°F/38°C and they

must never be painted, plated, coated,

or otherwise altered after leaving the

factory. Modified or over-heated sprin-

klers must be replaced.

Care must be exercised to avoid dam-

age to the sprinklers - before, during,

and after installation. Sprinklers dam-

aged by dropping, striking, wrench

twist/slippage, or the like, must be re-

placed.

The owner is responsible for the in-

spection, testing, and maintenance of

their fire protection system and de-

vices in compliance with this docu-

ment, as well as with the applicable

standards of the National Fire Protec-

tion Association (e.g., NFPA 25), in

addition to the standards of any other

authorities having jurisdiction. The in-

stalling contractor or sprinkler manu-

facturer should be contacted relative

to any questions.

It is recommended that automatic

TYPE TEMPERATURE

RATING

FRAME

COLOR

CODE

NATURAL

BRASS

135°F/57°C

360°F/182°C

PENDENT

(SIN G3102)

SPRINKLER FINISH

Unpainted

White

Blue

Red

1, 2, 3

165°F/74°C

212°F/100°C

280°F/138°C

NOTES:

1. Listed by Underwriters Laboratories, Inc.

2. Listed by Underwriters’ Laboratories of Canada.

3. Approved by Factory Mutual Research Corporation as Rack Storage Sprinklers.

TABLE A

LABORATORY LISTINGS AND APPROVALS

UPRIGHT

(SIN G3153)

135°F/57°C Unpainted

165°F/74°C Unpainted

212°F/100°C White

280°F/138°C Blue

360°F/182°C Red

1, 2, 3

1, 2

FIGURE B

W-TYPE 9 SPRINKLER WRENCH

WRENCH

RECESS

OBSOLETE

sprinkler systems be inspected,

tested, and maintained by a qualified

Inspection Service.

LIMITED WARRANTY

Products manufactured by Tyco Fire

Products are warranted solely to the

original Buyer for ten (10) years

against defects in material and work-

manship when paid for and properly

installed and maintained under normal

use and service. This warranty will ex-

pire ten (10) years from date of ship-

ment by Tyco Fire Products. No war-

ranty is given for products or

components manufactured by compa-

nies not affiliated by ownership with

Tyco Fire Products or for products and

components which have been subject

to misuse, improper installation, corro-

sion, or which have not been installed,

maintained, modified or repaired in ac-

cordance with applicable Standards of

the National Fire Protection Associa-

tion, and/or the standards of any other

Authorities Having Jurisdiction. Mate-

rials found by Tyco Fire Products to be

defective shall be either repaired or

replaced, at Tyco Fire Products’ sole

option. Tyco Fire Products neither as-

sumes, nor authorizes any person to

assume for it, any other obligation in

connection with the sale of products or

parts of products. Tyco Fire Products

shall not be responsible for sprinkler

system design errors or inaccurate or

incomplete information supplied by

Buyer or Buyer’s representatives.

IN NO EVENT SHALL TYCO FIRE

PRODUCTS BE LIABLE, IN CON-

TRACT, TORT, STRICT LIABILITY

OR UNDER ANY OTHER LEGAL

THEORY, FOR INCIDENTAL, INDI-

RECT, SPECIAL OR CONSEQUEN-

TIAL DAMAGES, INCLUDING BUT

NOT LIMITED TO LABOR CHARGES,

REGARDLESS OF WHETHER TYCO

FIRE PRODUCTS WAS INFORMED

ABOUT THE POSSIBILITY OF SUCH

DAMAGES, AND IN NO EVENT

SHALL TYCO FIRE PRODUCTS’ LI-

ABILITY EXCEED AN AMOUNT

EQUAL TO THE SALES PRICE.

THE FOREGOING WARRANTY IS

MADE IN LIEU OF ANY AND ALL

OTHER WARRANTIES EXPRESS

OR IMPLIED, INCLUDING WARRAN-

TIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PUR-

POSE.

ORDERING PROCEDURE

A Product Symbol Number (PSN) is

not specified when ordering sprinklers

with thread connections per ISO 7/1.

Contact your local distributor for avail-

ability.

Upright Sprinkler Assemblies:

Specify: 8.0 K-Factor, (specify tem-

perature rating), Model F917 Interme-

diate Level Upright Sprinkler with natu-

ral brass finish, PSN (specify from

Table B), as applicable).

Pendent Sprinkler Assemblies:

When pendent sprinkler assemblies

are required, the Pendent Sprinkler

and the F917 Pendent Shield Package

(shield & o-rings) are ordered sepa-

rately.

•Specify: 8.0 K-Factor, (specify tem-

perature rating), Model F916 Pen-

dent Sprinkler with natural brass fin-

ish, PSN (specify from Table C).

•Specify: Model F917 Pendent Shield

Package for 3/4 inch NPT, Model

F917 Intermediate Level Pendent

Sprinklers (one shield / two o-rings),

PSN 56-015-6-803.

“Special Order”

Upright Sprinkler Assemblies with

ISO 7/1 Thread Connections:

Specify: 8.0 K-Factor, (specify tem-

perature rating), Model F917 Interme-

diate Level Upright Sprinkler with natu-

ral brass finish and with thread

connection per ISO 7/1.

Sprinkler Wrench:

Specify: W-Type 9 Sprinkler Wrench,

PSN 56-000-1-849.

PSN 53 — XXX — 1 — XXX

165°F/74°C165

TEMPERATURE

RATING

135°F/57°C135

TYPE

TABLE B

PRODUCT SYMBOL NUMBER SELECTION FOR

8.0 K-FACTOR MODEL F917 INTERMEDIATE LEVEL

UPRIGHT SPRINKLERS

212°F/100°C

360

280°F/138°C280

360°F/182°C

212

153 NATURAL BRASS

UPRIGHT

PSN 53 — XXX — 1 — XXX

165°F/74°C165

TEMPERATURE

RATING

135°F/57°C135

TYPE

TABLE C

PRODUCT SYMBOL NUMBER SELECTION FOR

8.0 K-FACTOR MODEL F916 PENDENT SPRINKLERS

(SHIELDS AND O-RINGS ARE ORDERED SEPARATELY)

212°F/100°C

360

280°F/138°C280

360°F/182°C

212

102 NATURAL BRASS

PENDENT

OBSOLETE

WEIGHT

The nominal weights are as follows.

8.0 K-Factor Model F917

Upright Intermediate

Level Sprinkler . . . . . . . . . . . 5.8 ozs. (163 g)

8.0 K-Factor Model F916

Pendent Sprinkler . . . . . . . . 3.5 ozs. (99 g)

Model F917 Pendent

Shield Package (3/4" NPT) . 2.0 oz. (57 g)

W-Type 9

Sprinkler Wrench . . . . . . . . . 17 ozs. (480 g)

OBSOLETE

Otros manuales de Sistema de riego de Tyco Fire Product

Tyco Fire Product

Tyco Fire Product TY-QRF Manual de usuario

Tyco Fire Product

Tyco Fire Product Star E Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem STAINLESS STEEL QUARTZOID Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem F960/Q-48 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL B Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Pulsar S160QR Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Pulsar S195 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL A Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL A-1 Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem G102 Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem F895 Manual de usuario

Tyco Fire Product

Tyco Fire Product CC1 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL H Manual de usuario

Tyco Fire Product

Tyco Fire Product TFR MAX Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL Omega Prohibitor QR Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL Omega HEC-12EC Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Stealth S110 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star SG-R Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL Omega HEC-12 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Stealth S112 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Galaxy SG-RES Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem DS-1 Series Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL Omega R-1M Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL BV4-QREC Manual de usuario

Manuales populares de Sistema de riego de otras marcas

Hunter

Hunter Institutional Series Manual de usuario

Cellfast

Cellfast 52-305 Manual de usuario

Oral Care Technologies

Oral Care Technologies Hydro Floss Manual de usuario

Reliable

Reliable F1-300 Manual de usuario

Netafim

Netafim NETBEAT Manual de usuario

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manual de usuario

Tyco

Tyco CC3 Manual de usuario

Reliable

Reliable F4FR Manual de usuario

OpenSprinkler

OpenSprinkler OSPi Manual de usuario

EINHELL

EINHELL GE-WW 5537 E Manual de usuario

Valley

Valley Bender160 Manual de usuario

Reliable

Reliable F1FR42 Series Manual de usuario

Reliable

Reliable F1FR-300 Manual de usuario

Toro

Toro 730 Series Guía rápida

Eden

Eden 97063-EDAMZ Manual de usuario

Tyco

Tyco TY-L Series Manual de usuario

Johnson Controls

Johnson Controls tyco ESFR-17 Manual de usuario

Victaulic

Victaulic VicFlex I-VICFLEX.AQC-U Manual de usuario