Twilight FZ-MA100C Manual de usuario

Analizador de humedad Fuzhou

FZ-MA100C

Moisture Analyzer

Operation Manual

Table of Contents

1. Overview………………………………………………………………2

1.1 Overview…………………….……………………………………2

1.2 Safety precaution…………………………………………………3

2. Installation……………………………………………………………5

3. Operating………………………………………………………………6

3.2 Display’s Signal……………………………………………………6

3.3 Keypad……….……………………………………………………7

4. Parameter settings……………………………………………………8

4.1 Parameter settings................................................................9

4.2 Temperature setting……….……………………………………10

4.3 Testing mode setting………………………………………………10

4.4 Heating mode setting……………………………………………11

4.5 Timing mode setting.........……………………………………….……11

4.6 User-defined……………………………………………………12

5. Calibration……………………………………………….………….……12

6. Testing steps……………………………………………..………..….…..13

7. Optimize analyzing……………………………………..……..….…..….14

7.1 Heating temperature………………………………………...…………14

7.2 Heating time………………………………………………….……..…14

7.3 Sample weight…………………………………………………………15

7.4 Sample preparation……………………………………………………15

7.5 Sample species………………………………………………………15

8. Time setting…………………………………………………..…………..16

9. Data communication………………………………………..……………16

9.1 RS232 data setting ……………………………………………………17

9.2 RS232 pin ……………………………………………………….....…17

10. Data Storage…………………………………..…………….…………..18

11. Maintenance and troubleshooting…………………..…………………..18

12. Warranty……………………………………………………….………..19

Overview

1.1 About moisture analyzer

Moisture analyzer is a water measurement instrument equipped with

high-precision sensors and high-efficiency secondary thermal radiation device

on the basis of electronic balance to achieve rapid and accurate moisture

determination. Moisture analyzer

The Moisture analyzer is based on the thermodynamic principle, which

obtains the moisture percentage content and other results by the ratio of mass

to wet weight after material drying.

Moisture analyzers can pre-store a variety of different sample moisture

determination methods, making testing work fast and simple. Multiply

productivity and accuracy of measurement results compared to mechanical

products. The average sample can be measured in just a few minutes. The

instrument is simple to operate, accurate to test, the display part of the value is

clearly visible, and can display the moisture content value, dry matter content

value, sample initial value, final value, measurement time, temperature and

other data. And has the function of connecting with the computer and printer.

The Moisture analyzer can be widely used in all industries that need to

quickly analyze the moisture, to reach the requirements of various industries,

such as plastics, rubber, chemicals, medicine, food, and other industries in the

production and experimental process.

1.2 Safety precaution

In order to use the moisture analyzer safely and reliably, be sure to comply

with the following terms:

1.2.1. This instrument is use for measuring the moisture content of the samples.

Any improper operation may cause personal injury and damage to the

instrument.

1.2.2. Please confirm that the input voltage and plug type indicated on the label

match the AC power used in your area.

1.2.3 The power plug of this instrument is equipped with a grounding terminal.

It is forbidden to disconnect the grounding plug of the instrument. Do not

switch the size and frequency of the input supply voltage during the test.

1.2.4 Do not operate the moisture analyzer in a dangerous, humid or unstable

environment.

1.2.5 Unplug the power supply when cleaning the moisture analyzer.

1.2.6 Make sure there is enough space around the moisture analyzer and at

least 1 meter above it.

1.2.7 The moisture analyzer must be operated only by trained personnel who

are familiar with the performance of the tested sample and the operation of the

equipment.

Please use the relevant safety things to operate the moisture analyzer,

such as safety glasses, gloves, protective clothing and protective masks.

1.2.8 After-sales service should only be provided by authorized personnel from

the factory.

The moisture analyzer works by heating!

★ Do not place any flammable materials above, below or next to the moisture

analyzer.

★ When using the moisture analyzer, the samples, heating halogen lamps and

surrounding components can be very hot. Extra care should be taken when

moving samples to prevent burns.

★ Some samples require special care

★ Carefully analyze the possible dangerous consequences for any sample

material with safety hazards.

★ Fire/Explosion: Flammable and explosive sample heating with solvents

produces flammable and explosive gases or vapors, so they need to be

carried out in dry, low-temperature environments to prevent fire or

explosion.

★ Toxic/combustible: Samples of toxic or corrosive components should be

carried out in a well-ventilated environment, and such samples will release

toxic and corrosive gases during heating, so it is recommended to use as

few samples as possible.

★ Note: The user is should take all responsibilities for any damage

caused by testing the above types of samples.

Specification of moisture analyzer

Max weighing 100g 100g 100g

Display division 0.001g 0.005g 0.01g

Readability

(sample > 10g) 0.01% 0.05% 0.1%

Heating source Halogen lamp

Temperature setting 45℃ - 160℃

Weight calibration 100g

Pan Size φ110 (mm)

Dimensions （D*W*H）330*205*165(mm)

Package （D*W*H）410*315*335 (mm)

Net weight 3.2kg

Gross weight 4.6kg

2. Installation

2.1 Unpack carefully and check the machine and accessories against the below

packing list.

Standard configuration

Quantity Remarks

Moisture analyzer 1

Windshield 1

Sample tray holder 1

Power cable 1

Sample tray 1 box 5 aluminum pans per

box

100g weight 1 F2 Level

operation manual 1

2.2 Placement selection

★ The moisture analyzer should be placed on a stable, level surface console.

★ Choose a safe and well ventilated location. Samples with corrosive or toxic

fumes and other hazardous materials need to be specially prepared for

placement.

★ Please try to avoid placing the moisture analyzer in places with extreme

temperature fluctuations, excessive humidity, airflow, vibration,

electromagnetic fields, heat sources or direct sunlight.

2.3 Component installation

（1）Place the

windshield.

（2）Place the

sample tray holder.

（3）Place the sample

tray flat on the sample

tray holder.

2.4 Connect the power supply

Plug the correct end of the supplied power cord into the power input slot on the

back of the moisture analyzer, and connect the other end to the power outlet.

Note: For best measurement results, use or calibrate after at least 60

minutes of power up.

2.5 Adjustment level

The moisture analyzer has a horizontal bubble and two horizontal adjustment

feet. To compensate for the effect of the tilting symmetry of the placement

position during the weighing process, the horizontal foot can be adjusted until

the horizontal bubble is at the center position.

Note: The level must be re-adjusted each time the position changes.

Operation

3. Operating

The machine’s display

3.1 Display signal description:

g Weigh:grams

Automati

c mode

test

accuracy

Hi High precision

% Moisture content% M Medium precision

●g weightlessness Lo Low accuracy

100℃ Temperature

(degrees Celsius)

Hand Manual

customization

10:00 Time setting

(minutes: seconds) heating

method

fast

Opera

ting

mode

Auto Auto

standard

Time Time

slow

3.2 Control panel / keypad

Control panel function description

Button

Functi

on key

operat

ing

Features

Setting

Hold

Set heating parameters

Press

End of test: switch water content, solid content

and other parameters

Hold

Date time setting

Press

Print function key after the test is completed；

Parameter indicator icon change or numeric

increase button

Parameter settings

4. Parameter settings

★Select the appropriate working mode

1. Analyze the moisture automatically

When machine under auto mode, it will stop the analyzing automatically if

sample’s moisture changing within very small value.

2. Analyze the sample’s moisture manually

Use operating keypad manually to measure the sample’s moisture according

to its character

3. Timed analyzation

User set the analyze time, when time out, the machine will stop the analyzing

automatically.

4. High Precision 、Medium Precision 、Low Precision

5. The moisture analyzer heating method

Fast heating Heat to a set temperature in short time

Standard heating Heat to a set temperature in normal time

Slow heating Heat to a set temperature in long time

Tare Hold

Tare function key in weighing state；

Parameter indicator icon change or number

reduction button

Press

Enter calibration function

start/st

Press

Return function after testing

Test start/stop

On/off

Press

On/off

Tabla de contenidos

Otros manuales de Instrumento de medición de Twilight

Twilight

Twilight LT-DW6093 Manual de usuario

Twilight

Twilight ATAGO PAL-CLEANER Manual de usuario

Twilight

Twilight E2 Series Manual de usuario

Twilight

Twilight MP-2000 Manual de usuario

Twilight

Twilight TES-660 Manual de usuario

Twilight

Twilight ZTA Manual de usuario

Twilight

Twilight Tobias IQ150 Manual de usuario

Twilight

Twilight TENMARS TN-TM206 Manual de usuario

Twilight

Twilight FW-541019001 Manual de usuario

Twilight

Twilight Palette Series Manual de usuario

Twilight

Twilight MC-SUP2000H Manual de usuario

Twilight

Twilight Hioki HK-3280-10F Manual de usuario

Twilight

Twilight AT-DEC2 Manual de usuario

Twilight

Twilight LT-AM4205A Manual de usuario

Twilight

Twilight LG-DM1306D Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario