TV One Magenta MultiView 9D Manual de usuario

QSG-DA9-V1.00

Apr 2019

MultiView 9D Cat5 Distribution

Amplifier

Quick Start Guide V1.00

In this guide 
About your Multiview D9................................................................................ 1 
Cabling .......................................................................................................... 1 
Multiple devices ........................................................................................... 1 
Quick start ........................................................................................................ 2 
Troubleshooting and FAQs ............................................................................ 3 
No video signal or poor video quality at the transmitter local port or 
at the receiver .............................................................................................. 3 
Poor audio quality ....................................................................................... 3 
Serial communication doesn’t work correctly. ........................................ 3 
Cabling .............................................................................................................. 4 
Contact us......................................................................................................... 5 

QSG-DA9 1

About your Multiview D9

The Magenta MultiView Series System extends video signals over

ordinary Category 5 cable. All models use a transmitter-to-receiver

setup.

This device is not intended for, nor does it support, distribution through

an Ethernet network. Do not connect this device to any sort of

networking or telecommunications equipment.

Cabling

This device is compatible with Cat5/5e/6 data cabling as well as skew

free CAT5/5e cabling manufactured for video applications. Note that

some skew free Cat5 is specific to a particular vendor and is not

compatible with our products.

Please ensure any skew free CAT5 cable is non-proprietary prior to

purchase/ installation.

CAT6 cable, due to the manufacture method, can exhibit much greater

skew than standard CAT5/5e and may require skew compensation

beyond what the standard product offers. Please contact Magenta

Research for assistance.

CAT5/5e/6 cabling for the Magenta MultiView™ Series must be pinned

to the TIA-EIA T568B wiring specification. We recommend that all CAT5

cables be pre-terminated and tested. Cables terminated on-site or in an

existing infrastructure should be tested before use to ensure

compliance with the TIA-EIA T568B specification. Using incorrectly

terminated CAT5 cables can damage your device.

Multiple devices

The MultiView 9D 1x9 Distribution Amp utilizes industry standard CAT5

cabling to connect a MultiView transmitter and receivers.

Additional 9D 1x9 Distribution Amps may be cascaded via the UTP

THRU output or any other output if necessary.

2 tvONE

Quick start

1. Connect the RJ-45 cable from a MultiView transmitter unit or other

MultiView 9D 1x9 Video Distribution Amp into the port labeled UTP

IN.

2. Connect RJ-45 cables from MultiView receiver units into the ports

labeled OUTPUTS.

3. The port labeled UTP THRU may be used to cascade to other

MultiView 9D 1x9 Video Distribution Amps or can be used with a

MultiView receiver.

4. Connect the power supply to the unit.

5. Connect the included ground cable to the rear gold thumbscrew and

the other end to a suitable earth ground. The grounding is required

in instances where LCD monitors are used that do not provide a

ground via the DC power adapter. Failure to connect the ground

cable may result in loss of video signals.

QSG-DA9 3

Troubleshooting and FAQs

In most cases, nearly every issue with the MultiView Series can be resolved

by checking the CAT5 termination and making sure that it’s pinned to the

TIA/EIA 568B wiring specification. However, there may be other problems

that cause the system to not perform as it’s designed. Below are solutions to

the most common installation errors.

No video signal or poor video quality at the transmitter

local port or at the receiver

1. Check that all units are powered.

2. Ensure EQ adjustment on receiver is set correctly.

3. Make sure the CAT5 cable is terminated correctly perthe TIA/EIA

568B wiring specification.

4. Is the display device powered on and functioning?

5. Check to ensure display settings (resolution, refresh rate, etc) are

compatible with input signal.

Poor audio quality

1. Powered speakers are required. Make sure speaker power is ON.

2. Check input source levels from the source device. Make sure the

audio source is not overdriven or underdriven.

3. Audio is summed left and right for “A” versions. If using a single

channel, both audio inputs must be connected at the transmitter

end for full audio gain. Audio is line level.

4. SA serial//audio units support full stereo line level. A high frequency

noise may be heard if the Cat5 cable from the transmitter is

disconnected, or the transmitter is not powered up. This is normal

and will disappear once a complete link connection is made.

Serial communication doesn’t work correctly.

1. Are the serial devices connected properly? Are the serial parameters

correct for source/destination devices?

2. When using RS-232 transmitters or receivers in daisy chains, Cat5

switches, 9D Cat5 distribution amps, or Multi-output transmitters,

the serial signal is a unidirectionally broadcast mode only. In this

4 tvONE

mode, all other MultiView™ CAT5 Video System devices must be the

simplex serial type.

Cabling

tvone.com

[email protected]

Support NCSA: [email protected]

Support EMEA: [email protected]

Support Asia: [email protected]

Information in this document is subject to change without notice. No part of this publication

may be reproduced, stored in a retrieval system, or transmitted in any form or any means

electronic or mechanical, including photocopying and recording for any purpose other than

the purchaser's personal use without the written permission of tvONE.

Registered in the U.S. Patent and Trademark Office.

Tabla de contenidos

Otros manuales de Amplificador de TV One

TV One

TV One 1T-VGA-412 Manual de usuario

TV One

TV One 1T-DA8CVB Manual de usuario

TV One

TV One 1T-VGA-412 Manual de usuario

TV One

TV One 1T-DA-682 Manual de usuario

TV One

TV One 1T-DA8CVB Manual de usuario

TV One

TV One 1T-DA-124 Manual de usuario

TV One

TV One 1T-DVI-512 Manual de usuario

TV One

TV One 1T-DA-552 Manual de usuario

TV One

TV One 1T-DA-672 Manual de usuario

TV One

TV One TASK 1T-DA-552 Manual de usuario

TV One

TV One 1T-DA-124 Manual de usuario

TV One

TV One 1T-DVI-512 Manual de usuario

TV One

TV One 1T-DA-726 3G Manual de usuario

TV One

TV One 1T-DA-472 Manual de usuario

TV One

TV One 1T-DA-462 Manual de usuario

TV One

TV One TASK 1T-DA-552 Manual de usuario

TV One

TV One 1T-DA-672 Manual de usuario

TV One

TV One 1T-VGA-412 Manual de usuario

TV One

TV One 1T-DA-674 Manual de usuario

TV One

TV One 1T-DA8CVB Manual de usuario

TV One

TV One 1T-DA8CVB Manual de usuario

TV One

TV One 1T-DA-652 Manual de usuario

TV One

TV One 1T-DA-726 HD Manual de usuario

TV One

TV One PD-760SVA Manual de usuario

Manuales populares de Amplificador de otras marcas

ASTRO

ASTRO HVO V40 P Manual de usuario

Marantz

Marantz SUPERSCOPE BLA-545 Instrucciones de montaje

NAD

NAD CI980 Manual de usuario

Technics

Technics SE-CH770 Manual de usuario

Harman Kardon

Harman Kardon HK6300 Manual de usuario

NAD

NAD T975 Manual de usuario

McIntosh

McIntosh MA6850 Manual de usuario

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manual de usuario

Viatron

Viatron Autrix Manual de usuario

GME

GME GA9800 Manual de usuario

Atlas

Atlas CP700 Manual de usuario

Roland

Roland KC-1000 Manual de usuario

Pyle

Pyle PFMRA350BW Manual de usuario

Advantage

Advantage S-250 Manual de usuario

IRT Electronics

IRT Electronics DVA-3007 Manual de usuario

Dimavery

Dimavery BA-100 Series Manual de usuario

Sony

Sony XM-S400D Manual de usuario

Schertler

Schertler ROY X Manual de usuario