turck BC3-M12-AP6X 15M Manual de usuario
Capacitive sensor
BC3-M12-AP6X/S90/3GD 15M
Edition • 2017-06-25T02:09:33+02:00
1 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Type designation BC3-M12-AP6X/S90/3GD 15M
Ident no. 2601004
Rated switching distance (flush) 3 mm
Rated switching distance (non-flush) 3 mm
Secured operating distance ð (0.72 x Sn) mm
Hysteresis 2…20 %
Temperature drift type 20 %
Repeat accuracy ð 2 % of full scale
Ambient temperature -25…+70 °C
For explosion hazardous areas see instruction
leaflet
Operating voltage 10…30 VDC
Residual ripple ð 10 % Uss
DC rated operational current ð 200 mA
No-load current I0ð 15 mA
Residual current ð 0.1 mA
Switching frequency 0.1 kHz
Isolation test voltage ð 0.5 kV
Output function 3-wire, NO contact, PNP
Short-circuit protection yes/ Cyclic
Voltage drop at Ieð 1.8 V
Wire breakage/Reverse polarity protection yes/ Complete
Approval acc. to ATEX declaration of conformity TURCK Ex-03025H
X
Device marking Ex II 3 G Ex nA IIC T5 Gc / II 3 D Ex t IIIC T91°C Dc
Warning Protect against mechanical damage
Design Threaded barrel, M12 × 1
Dimensions 63.5 mm
Housing material Metal, CuZn, Chrome-plated
Active area material Plastic, ABS, yellow
Admissible pressure on front cap ð 5 bar
Max. tightening torque housing nut 10 Nm
Electrical connection Cable
Cable quality Ø 4, LifYY-11Y, PUR, 15m
Cable cross section 3 x 0.25 mm2
Vibration resistance 55 Hz (1 mm)
Shock resistance 30 g (11 ms)
Protection class IP67
MTTF 1080 years acc. to SN 29500 (Ed. 99) 40 °C
Switching state LED yellow
■ATEX category II 3 G, Ex zone 2
■ATEX category II 3 D, Ex zone 22
■M12 × 1 threaded barrel
■Chrome-plated brass
■Fine adjustment via potentiometer
■DC 3-wire, 10…30 VDC
■NO contact, PNP output
■Cable connection
Wiring Diagram
Functional principle
Capacitive proximity switches are designed
for non-contact and wear-free detection of
electrically conductive as well as non-conduc-
tive metal objects.
Capacitive sensor
BC3-M12-AP6X/S90/3GD 15M
Edition • 2017-06-25T02:09:33+02:00
2 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Mounting instructions/Description minimum distances
Distance D 24 mm
Distance W 9 mm
Distance S 18 mm
Distance G 18 mm
Diameter active area B Ø 12 mm
The given minimum distances have been checked
against the standard switching distance.
Should the sensitivity of the sensors be changed via
potentiometer, the data sheet specifications no longer
apply.
Capacitive sensor
BC3-M12-AP6X/S90/3GD 15M
Edition • 2017-06-25T02:09:33+02:00
3 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Accessories
Type code Ident no. Description
MAP-M12-PP 6950016 Mounting adapter; material: Polypropylene; sensor replace-
ment with filled container possible (adapter remains in con-
tainer during sensor replacement)
MAP-M12-PVDF 6950017 Mounting adapter; material: Polyvenylidenflourid; sensor can
be replaced with filled container (adapter remains in contain-
er during replacement)
BST-12B 6947212 Fixing clamp for threaded barrel devices, with dead-stop; ma-
terial: PA6
Capacitive sensor
BC3-M12-AP6X/S90/3GD 15M
Edition • 2017-06-25T02:09:33+02:00
4 / 4 Hans Turck GmbH & Co.KG ñ D-45472 Mülheim an der Ruhr ñ Witzlebenstraße 7 ñ Tel. 0208 4952-0 ñ Fax 0208 4952-264 ñ [email protected] ñ www.turck.com
Operating manual
Intended use
This device fulfills the directive 2014/34/EC and is suited for use in explosion hazardous areas acc. to EN60079-0:2009, EN60079-15:2010 and
EN60079-31:2009.
In order to ensure correct operation to the intended purpose it is required to observe the national regulations and directives.
For use in explosion hazardous areas conform to classification
II 3 G and II 3 D (Group II, Category 3 G, electrical equipment for gaseous atmospheres and category 3 D, electrical equipment for dust atmo-
spheres).
Marking (see device or technical data sheet)
Ex II 3 G and Ex nA IIC T5 Gc acc. to EN 60079-0:2009 and EN 60079-15:2010 and Ex II 3 D Ex t IIIC T91°C Dc acc. to EN 60079-0:2009 and
EN 60079-31:2009
Installation / Commissioning
These devices may only be installed, connected and operated by trained and qualified staff. Qualified staff must have knowledge of protection
classes, directives and regulations concerning electrical equipment designed for use in explosion hazardous areas.
Please verify that the classification and the marking on the device comply with the actual application conditions.
Installation and mounting instructions
Avoid static charging of cables and plastic devices. Please only clean the device with a damp cloth. Do not install the device in a dust flow and
avoid build-up of dust deposits on the device.
If the devices and the cable could be subject to mechanical damage, they must be protected accordingly. They must also be shielded against
strong electro-magnetic fields.
The pin configuration and the electrical specifications can be taken from the device marking or the technical data sheet.
In order to avoid contamination of the device, please remove possible blanking plugs of the cable glands or connectors only shortly before in-
serting the cable or opening the cable socket.
Special conditions for safe operation
Devices with terminal chamber (cable glands) have a weaker strain relief. Sufficient strain relief must be ensured or the cable must be station-
ary-mounted.
Do not disconnect the plug-in connection or cable under voltage.
Please attach a warning label permanently in an appropriate fashion in close proximity to the plug-in connection with the following inscription:
Nicht unter Spannung trennen / Do not separate when energized.
The device must be protected against any kind of mechanical damage and degrading UV-radiation. On selecting the approval-relevant acces-
sories, always ensure that they are installed conform to the application.
Load voltage and operating voltage of this equipment must be supplied from power supplies with safe isolation (IEC 30 364/UL508), to ensure
that the rated voltage of the equipment (24 VDC +20% = 28.8 VDC) is never exceeded by more than 40%.
service / maintenance
Repairs are not possible. The approval expires if the device is repaired or modified by a person other than the manufacturer. The most important
data from the approval are listed.
Este manual sirve para los siguientes modelos
3
Otros manuales de Accesorios de turck
turck
turck FMX-IM-2UPLI63FX Manual de usuario
turck
turck RI360P1-DSU35-CNX4 Series Manual de usuario
turck
turck FCS-G1/2A4-NAEX Manual de usuario
turck
turck RU Series Manual de usuario
turck
turck FCS-GL1/2A4-NAEX Manual de usuario
turck
turck NIMFE-EM12/4,9L88-UP6X-H1141/S1182 Manual de usuario
turck
turck BI1.5-HS865-Y1 Manual de usuario
turck
turck RU130U-M18E-LI8X2-H1151 Manual de usuario
turck
turck NI4-DSU35TC-2AP4X2/3GD Manual de usuario
turck
turck PS Series Manual de usuario
turck
turck NI5-EM12-Y1X-H1141 Manual de usuario
turck
turck LTX-R10 Series Manual de usuario
turck
turck PK01VR N Series Manual de usuario
turck
turck FCS-GL1/2A4-NAEX-H1141/A Manual de usuario
turck
turck FCS-G1/4A4-NAEX Manual de usuario
turck
turck LUS211 Series Manual de usuario
turck
turck Uprox+ BI15U-EM30WD-AP6X-H1141/3GD Manual de usuario
turck
turck FS100 L Series Manual de usuario
turck
turck LRS510 Series Manual de usuario
turck
turck FCS-G1/2A4-NAEX/L065/D100 Manual de usuario
Manuales populares de Accesorios de otras marcas
IFM Electronic
IFM Electronic Efector 250 Series Guía de referencia
DigiDesign
DigiDesign 888/24 I/O Manual de usuario
PROZIS
PROZIS QUAY Manual de usuario
patagonia
patagonia PSI Vest Manual de usuario
SFC Energy
SFC Energy EFOY GO! Manual de usuario
Axminster
Axminster Tooling Stylus Tip Ballpoint Pen Kit Manual de usuario