TURBO RACING P32-S Manual de usuario
www.turboracinghobby.com
2.4GHz 4CH LCD RADIO SYSTEM
P32-S
www.turboracinghobby.com
Thank you for choosing our company's products! If this is your rst time using this remote controller, please read this
manual carefully before using it and operate it follow the instructions strictly. You can also check the manual if you
encounter problems during the operation. Please keep the manual after use for future use. Thank you again for using
our products and hope to bring you a new and interesting world.
If you nd any problems in using our products, please check the instructions for the rst time. Or if you need our relevant
information, you can contact us through our website: www.turboracinghobby.com
Introduction
Services
Copyright NewStone Technology co.,ltd
14+ This product is not suitable
for children under 14 years.
This safety warning must be strictly implemented. As company policy shall not be liable for any loss caused by failure to comply
with the safety warning. Should you ignore the operating and safety instructions, the warranty will be void.
This product is not a toy, its operation must be learned step by step. And only suitable for people who over 14 years. Please do not
let children operate the model, and be careful when have children on site when operating models.
www.turboracinghobby.com
RADIO SPECIFICATIONS
RECEIVER SPECIFICATIONS
P32-S
AAA x4
137.00
4CH
164.60
68.70
RX41
Receiver Gyro RX
RX49
4.8 - 10.0V
4CH
RX47
Receiver
4.8 - 10.0V
6CH
36x26x14
L x H x W (mm)
L (mm)
H (mm)
W (mm)
www.turboracinghobby.com
Functions LCD
LCD Display
Steering wheel
Antenna
Throttle trigger Power
Bat box
ST trim+
ST trim-
Disassemble key
CH3
- button
+ button
SEL/CH
LCD Display
1. The LCD interface automatically turns o the light guide lamp after 10
seconds without any operation.
2. The buzzer will beep intermittently after 9 minutes without any operation
of the remote control/30 seconds before it goes into sleep It is automatically
turned o. You need to restart to enter the working mode normally.
Disassemble Handle & Install
1.Press the button
2.take away the handle
3.press the button, install the handle
CH3
CH3 key setting function: CH3 key can automatically switch between positive and
negative output self-locking or non self-locking. Long press CH3 key buzzer to give
a sound, indicating successful switching. (Factory default self-locking)
Restore factory settings: In the startup state, long press and hold the "SEL/CH" button,
the buzzer will beep once, the LCD screen will go out, and then restart.
Battery Installation Receiver Installation & Connection
Pairing The Transmitter & Receiver(RX41)
Connection(RX41)
Electric powered model
AUX 3 2 1
ESC
Steering Servo
Receiver
AUX 3 2 1 AUX 3 2 1
LED
3.
4.
Connection
(RX47)
User group mode A/N/B, factory default N mode.
We have added three user group modes with switch
adjustment, but now this feature is only available for
remote control with user group mode.
User group mode
CH1
CH2
CH3
CH4
CH5
CH6
Antenna
转向伺服（CH1）
油门伺服（CH2）
伺服 (CH3)
伺服 (CH4)
伺服 (CH5)
伺服 (CH6)
Switch
Analog Servo
(General response）
Digital Servo
((Quick response）
Receiver battery case
Pairing The Transmitter & Receiver
(RX47)
LED
2. Turn on the transmitter.
4. When the LED on the receiver becomes solid,the binding process is completed.
Tip: When pairing, user group mode defaults to N mode.
Default N mode
3.
Connection(RX49)
Pairing The Transmitter & Receiver(Rx49)
Note: Radio systems installed in RTRs have already been bound. Only when
installing a new transmitter or receiver is the above process necessary,
LED
Gain - This setting adjusts the sensitivity and speed of the counter-steer effect and is adjustable in eight
steps indicated by the number of flashes of the LED with 1 being the most sensitive and 7 the least
sensitive. Setting 8 disables. A setting of 4 is set by default and is suitable for most applications and
conditions. To change the setting, press and release the Gain button. The L ED will flash to indicate the
new setting. Continue this process until the desired setting is reached making sure to allow the LED
sequence to finish before pressing the Gain button again.
ESC
Steering Servo
1. After connecting the receiver to a power source (receiver battery or ESC) and turning it on.
2. Switch on the transmitter.
4. The LED on the receiver will now remain solid to indicate successful binding of the
transmitter and receiver.
Rev/Nor - This setting changes the direction of 's counter-steer
effect and is set at Normal by default. In all situations, should
counter-steer (steer into the slide) automatically. But in rare cases, the
direction setting must be reversed. To reverse the setting, press and
hold the Nor/Rev button for 3-4 seconds until the L .ED flashes twice to
indicate that the direction has been changed successully.
Gyro Receiver
3.Connect the Bind connector to the“Pair”pins on the receiver. The LED
on the receiver will flash rapidly,and then remove the Bind connector
from the receiver.
CH4 M: M stands for middle
CH4 L: L stands for base
CH4 H: H stands for height
Operation
Using Caution While Operating
Fail safe function setting
General Care
1. Always use clean, dry cloth or soft bristle brush to clean your equipment.
2. Never use chemical cleansers, as these could damage the sensitive electronics and plastics.
Please turn on the TX, then pull the TH trigger anywhere you want to and hold it, press the SW button
of the receiver about 2sec,the LED should start ashing for 5sec,then release SW button and
TH trigger, turn o the TX.
Tabla de contenidos
Otros manuales de Controladores de TURBO RACING
