TSS DUR 120 USB Manual de usuario

DUR 120 USB

and

DUR 120 ETHERNET

Desktop UHF RFID reader

User Guide

Ver. 1.3

04/2016

TSS COMPANY s.r.o., Pod Rovnicami 41, 84104 Bratislava, Slovakia

eb: .tsscompany.eu email: [email protected]

No part of this manua may be reproduced in any form or by any means, e ectronic,

mechanica , recording, or otherwise, without the prior written permission of TSS COMPANY.

TSS COMPANY reserves the right to modify its product specifications without any further

notice. For up to date information p ease visit www.tsscompany.eu.

The information contained herein has been carefu y checked and is be ieved to be accurate.

However, TSS assumes no responsibi ity for inaccuracies.

Contents

Introduction ........................................................................................................................ 4

Connecting the reader and installing the USB driver ......................................................... 4

Ethernet connection (Only DUR 120 ETHERNET) ............................................................... 4

Functionality test ................................................................................................................ 4

Technical specifications ...................................................................................................... 5

TSSTagger ........................................................................................................................... 7

Installation ................................................................................................................... 7

Inventory Tab ............................................................................................................... 8

Read/Write Tab ......................................................................................................... 10

Kill/Lock Tab ............................................................................................................... 12

EPC Tab ...................................................................................................................... 14

Settings Tab ............................................................................................................... 16

Reader Settings .................................................................................................. 17

Inventory ............................................................................................................ 17

Connect Tab ............................................................................................................... 18

Connection Type (a) ........................................................................................... 19

Serial Port Settings (c) ........................................................................................ 19

LAN Settings (f) ................................................................................................... 19

Device Search (j) ................................................................................................. 20

Device Net ork Settings (q) ............................................................................... 21

TSSUpdater ....................................................................................................................... 22

Installation ................................................................................................................. 22

Firm are update ....................................................................................................... 22

Troubleshooting......................................................................................................... 26

References ........................................................................................................................ 27

Revision History ................................................................................................................ 28

Annex 1: Declaration of Conformity......................................................................................... 29

1Introduction

The desktop UHF RFID reader DUR 120 a ows so ution deve opers to use app ications that

require desktop reading and writing of EPCg oba UHF C ass 1 Gen 2 tags. The DUR 120 reader

is contro ed by and powered from a host PC or aptop through a USB interface. In case of DUR

120 ETHERNET the ethernet interface can be used for communication purpose.

2Connecting the reader and installing the USB driver

The DUR 120 reader can be connected to a PC or a notebook via a USB interface. When

connecting the device for the first time, the user has to insta the necessary device drivers to

a ow Windows to recognize the reader. The reader emu ates a virtua seria port.

You can down oad VCP drivers for Windows based systems from this website:

http://www.ftdichip.com/Drivers/VCP.htm

You can down oad detai ed driver insta ation guide from this website:

http://www.ftdichip.com/Support/Documents/InstallGuides.htm

3Ethernet connection (Only DUR 120 E HERNE )

A standard ethernet connection with an 8-pin RJ connector using 2 twisted pairs has to

be used to connect DUR 120 ETHERNET. The DUR 120 ETHERNET se ects automatica y

between the USB and ethernet interface based on the first received va id packet after the start

up from USB or ethernet interface. The DUR 120 ETHERNET reader is powered through the

USB connector.

4Functionality test

The user can easi y test the basic functiona ities of the reader with the TSSTagger demo

software. Chapter 6 of this guide contains more information on TSSTagger.

5echnical specifications

DUR 120 USB:

Frequency Band: 865 ÷ 868 MHz (ETSI EN 302 208 v. 1.4.1.)

Number Of Channels: 4 (comp iant to ETSI EN 302 208 v. 1.4.1.)

RF Po er Output – e.r.p.: max. 14 dBm

Modulation: DSB-ASK

Antenna Gain: 5 dBic

Antenna Polarization: Integrated circu ar po arized antenna

Air Interface Protocol: EPCg oba UHF C ass 1 Gen 2 Version 2.0.0

Supports tag vendor specific custom commands

Supports NXP UCODE DNA

Tag Communication Rate: 40 kbps

Data Encoding

Interrogator -> Tag:

PIE, 40kHz

Data Encoding

Tag -> Interrogator:

FM0, 40kHz

Tag Read Rate: Up to 50 tags/second

Tag Read Range: Up to 50 cm, depending on tag and environment

(Tested with an ALN-9662 tag)

USB Interface:

USB 2.0 Fu Speed

It appears as USB seria port

USB mini-B connector

User Interface:

Power LED (orange)

Status LED (green)

Operating Temperature: -20 °C do +55 °C

Po er Supply: 5 VDC (Powered by USB interface)

Po er Consumption: max. 200mA

Dimensions: 110mm L x 110mm W x 38mm H

Weight: 240 g

Length Of USB Cable: 1,8m

DUR 120 ETHERNET:

Frequency Band: 865 ÷ 868 MHz (ETSI EN 302 208 v. 1.4.1.)

Number Of Channels: 4 (comp iant to ETSI EN 302 208 v. 1.4.1.)

RF Po er Output – e.r.p.: max. 14 dBm

Modulation: DSB-ASK

Antenna Gain: 5 dBic

Antenna Polarization: Integrated circu ar po arized antenna

Air Interface Protocol: EPCg oba UHF C ass 1 Gen 2 Version 2.0.0

Supports tag vendor specific custom commands

Supports NXP UCODE DNA

Tag Communication Rate: 40 kbps

Data Encoding

Interrogator -> Tag:

PIE, 40kHz

Data Encoding

Tag -> Interrogator:

FM0, 40kHz

Tag Read Rate: Up to 50 tags/second

Tag Read Range: Up to 50 cm, depending on tag and environment

(Tested with an ALN-9662 tag)

Ethernet Interface : 10/100 Mbps

TCP/IP protoco s

Supports IP Configuration

- Static, DHCP

Supports DNS

(Defau t configuration is: Static IP Address,

192.168.0.110)

USB Interface:

USB 2.0 Fu Speed

It appears as USB seria port

USB mini-B connector

User Interface:

Power LED (orange)

Status LED (green)

Operating Temperature: -20 °C do +55 °C

Po er Supply: 5 VDC (Powered by USB interface)

Po er Consumption: max. 450 mA

Dimensions: 110mm L x 110mm W x 66mm H

Weight: 290 g

Length Of USB Cable:: 1,8m

6TSSTagger

The user interface of TSSTagger is split into five sections, or tabs:

Inventory Tab:

This is the main tab of the application used to connect and disconnect the reader and to

start and stop the HID emulation. This tab also contains the inventory list here EPC

numbers are stored.

Read/Write Tab:

This tab is used to read from and rite to different memory banks of the tag.

Kill/Lock Tab:

This tab is used to adjust lock actions and permissions for different memory banks and

pass ords.

EPC Tab:

This is the application’s EPC editor designed for easy EPC number editing.

Settings Tab:

This tab contains several application settings.

Installation

-Extract the contents of TSSTagger.zip into the program directory.

-Double-click vcredist_x86.exe to start the setup of Microsoft Visual C++ 2013 x86

Redistributable soft are package.

-The setup program guides you through the installation.

-Wait until Microsoft Visual C++ 2013 x86 Redistributable soft are package has been

successfully installed.

Inventory Tab

a. Connect reader:

This button serves to connect and disconnect the reader. To ensure the reader

ill connect properly, the user should ait until Windo s USB drivers have

properly installed (this can be confirmed in the lo er right corner of the screen in

the Windo s task bar notification area).

b. Clear inventory list:

This button c ears the inventory ist.

c. Inventory list:

This is where read counts of tags and EPC numbers are isted, sorted by time

stamp. The maximum number of tags to be disp ayed in the inventory ist can be

set in the “Settings Tab”. The ist can be c eared using the “Clear inventory list”

button ocated under the inventory ist.

d. Read Single-Tag:

This button a ows the user to read the EPC number of the tag, disp aying it in the

inventory ist.

e. Read Multi-Tag:

This button a ows the user to read the EPC numbers of mu tip e tags.

f. Main log:

The main og shows the connection status, sent and received packets and error

messages re ated to seria port communication. Content of the main og can be

copied and pasted or c eared using the right-c ick context menu.

g. Status Bar:

The status bar shows information about the current y connected device and any

other messages.

Read/Write Tab

a. Tag selection:

These radio buttons allo the user to select bet een orking ith the first tag

responding to the reader and the tag specified by the EPC number.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema RFID de TSS

TSS

TSS HUR 120 Manual de usuario

Manuales populares de Sistema RFID de otras marcas

Chainway

Chainway R1 Manual de usuario

IFM

IFM DTC600 Manual de usuario

Elatec

Elatec TWN4 MULTITECH NANO LEGIC 63 M Manual de usuario

RHOMBUS

RHOMBUS DR20 Manual de usuario

Sirit

Sirit IDentity 6204 Manual de usuario

SOREX

SOREX FLEX Manual de usuario

Omron

Omron V780-HMD68-EIP-KR Manual de usuario

IDENTEC SOLUTIONS

IDENTEC SOLUTIONS iPOINT Si Instrucciones de uso

Shuttle

Shuttle BR06 Instrucciones de uso

Digilock

Digilock Curve Keypad Basic Manual de usuario

Atid

Atid AT870 Manual de usuario

Chacon

Chacon 34958 Manual de usuario

Paxton

Paxton PROXIMITY architectural reader Manual de usuario

CipherLab

CipherLab 1800 series Manual de usuario

Brady

Brady FR22 Manual de usuario

Kronotech

Kronotech BLUEBOX GEN2 M30 UHF Manual de usuario

Unitech

Unitech RH767 Manual de usuario

Honeywell

Honeywell 026366.00 Manual de usuario