Tru CORDLESS RC-500CP Manual de usuario
2
3
IMPORTANT SAFEGUARDS
When using electrical appliances especially when children are present, basic safety precautions should always be
followed to reduce the risk of re, electric shock, and/or injury to persons, including the following:
1. READ ALL INSTRUCTIONS.
2. To protect against re, electrical shock, or injury to persons DO NOT put charging cord, charger adapter or appliance in water or
other liquid.
3. This appliance is not intended for use by children or by persons with reduced physical, sensory, or mental capabilities, or lack of
experience and knowledge. Close supervision is necessary when any appliance is used near children. Children should be supervised
to ensure that they do not play with the appliance.
4. Unplug charger adapter from outlet when not in use, before putting on or taking off parts and before cleaning. To unplug, grasp the
charger adapter and pull from the outlet. Never pull from the charging cord.
5. Avoid contacting moving parts.
6. Do not operate or charge the appliance with a damaged charging cord or charger adapter, or after the appliance malfunctions, or
is dropped or damaged in any manner. Contact the manufacturer at their customer service telephone number for information on
examination, repair, or adjustment.
7. The use of attachments not recommended or sold by the appliance manufacturer may cause re, electric shock or injury.
8. Do not use outdoors.
9. Do not let charging cord hang over edge of table or counter or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Keep hands and utensils out of the containers while blending or chopping to prevent the possibility of severe injury to persons or
damage to the unit. A scraper may be used but must be used only when the unit is not running.
12. Never add to container while appliance is operating.
13. There is a risk of thermal burn injury with the personal blender due to excessive pressure in the container. Do not blend hot liquids.
To turn the motor housing unit off, release the speed buttons (HI or LOW) located on the top of the unit.
14. To turn the motor housing unit off, release the speed buttons (HI or LOW).
15. To reduce the risk of injury with the unit, never place the chopping blade or the blending blade into the motor housing unit. Place
the chopping blade into the glass chopping bowl and then assemble chopper collar and then motor housing unit onto the chopping
bowl. Likewise, place the blending blade into the blender jar and then assemble blender collar and then motor housing unit onto the
4
blender jar.
16. Containers must be properly in place before operating the appliance.
17. Blades are sharp, are not locked in place and are removable. Handle with care. When handling blades, always hold by the shaft. To
avoid a risk of injury, carefully remove the blades before pouring out food contents.
18. Do not use an extension cord. Plug charger directly into an electric outlet. Use only with the charger provided with the appliance. Do
not attempt to use this charger with any other product. Likewise, do not attempt to charge this appliance with any other charger. Do
not use appliance for other than intended use.
19. Do not incinerate this appliance even if it is severely damaged. The batteries can explode in a re.
20. Do not use appliance for other than intended use.
SAVE THESE INSTRUCTIONS
5
This appliance is for HOUSEHOLD USE ONLY.
The charger may be plugged into an AC electrical outlet (ordinary household current). Do not use any other electrical outlet.
DO NOT USE THE USB CHARGER IF THE LINE CORD OR PLUG SHOWS ANY DAMAGE
Only use Tru Model P12DUSB050200 US charger (Input:100-240VAC, 50/60Hz, 0.3A, Output:5.0VDC, 2.0A) to charge the blender Model
RC-500CPCN. Do not attempt to charge the motor housing unit with any other charger.
CHARGER ADAPTER / CHARGING CORD SAFETY TIPS
1. Never pull or yank on charging cord.
2. To insert the charger adapter, grasp it rmly and guide it into outlet.
3. To disconnect, grasp charger and remove it from outlet. Do not pull on the cord.
4. Before each charging, inspect the charging cord for cuts and/or abrasion marks. If any are found, this indicates that the
charging cord should be replaced.
5. Never wrap the cord tightly around the appliance, as this could place undue stress on the cord where it enters the charger
adapter or charging port on the appliance and cause it to fray and break.
6
7
CORDLESS BLENDER & CHOPPER FEATURES
1. High capacity lithium/ion battery
2. Light, quiet, convenient and easy to clean
3. Easy to charge
4. 2 Operation Speeds
5. Stainless steel high speed cutting blade
6. Blender jar with pour spout and storage lid
7. Glass chopping bowl with storage lid
8. Non-skid trivet
PREPARING FOR USE
1. Carefully unpack the motor housing unit and all parts. Remove any tape, labels or packaging materials.
2. Wash all product pieces carefully except for the motor housing unit with warm, soapy water. Rinse and dry thoroughly.
3. Wipe exterior surfaces of the motor housing with a soft, moist cloth to remove dust particles collected during packing and handling.
NEVER IMMERSE THE MOTOR HOUSING, CHARGING CORD OR CHARGER ADAPTER IN WATER OR ANY OTHER LIQUID.
4. Be sure all parts are properly assembled and in place before use.
HOW TO CHARGE
1. Open the charging port on the motor housing. Attach micro end of charging cord to the motor housing.
2. Attach the USB connector (larger end) on the charging cord to the charger adapter.
3. Plug the charger adapter into the wall outlet.
4. Indicator lights will ash while charging. The lights will stop ashing once the unit is fully charged. See Indicator Light section for
details. Note: The unit is shipped with approximately 30% charge in the batteries. One or two lights will be illuminated during use.
The unit will operate properly without charging. It is recommended to fully charge before rst use for best performance.
5. It will take approximately 5 hours to fully charge the unit.
8
ASSEMBLING THE BLENDER
Hold the blender blade by the shaft and push onto the metal shaft in the bottom of the blender jar until secure. Align the U-shape openings
on the blender collar with the U shapes in the blender jar and push in place. Align the pins in the blender collar with the small openings in
the motor housing and place the motor housing onto the blender collar. The motor housing should t ush with no gaps.
ASSEMBLING THE CHOPPER
Hold the chopper blade by the shaft and push onto the metal shaft in the bottom of the chopping bowl until secure. Align the U-shape
openings on the chopper collar with the U shapes in the chopping bowl and push in place. Align the pins in the chopper collar with the
small openings in the motor housing and place the motor housing onto the chopper collar. The motor housing should t ush with no gaps.
9
HOW TO USE THE BLENDER
This blender can be used just like a normal blender but without the cord!
1. Place blender blade onto metal shaft in the bottom of the blender jar.
2. Place food to be blended into the jar. Do not overll.
3. Place the blender collar and motor housing onto the jar. The lights will ash on to indicate the unit is ready to use.
4. Press the I (low) or II (high) speed button on top of the motor housing.
5. Allow the blender to work through the blending process. Do not shake or move the blender while operating.
6. When blending has nished, release the speed button and the unit will stop.
7. Ensure the blade has completely stopped before removing the motor housing and blender collar.
8. Remove the blender blade by grasping the shaft rmly and lift up. Be careful, the blades are sharp!
9. After the blender blade has been removed the ingredients can be poured from the blender jar.
10. Do not use the blender for longer than 1 minute continuously. After 1 minute of continuous use, the unit may become over-heated.
Allow the unit to rest for at least 5 min before resuming use.
11. The lights will extinguish as the battery life reduces. A fully charged unit will show all three lights. When only the lowest light is
illuminated and ashing, this incidates that the unit needs to be charged.
HOW TO USE THE CHOPPER
This chopper can also be used just like a normal chopper but without the cord!
1. Place chopping blade onto metal shaft in the bottom of the chopping bowl.
2. Place food to be chopped into the bowl. Do not overll.
3. Place the chopper collar and motor housing onto the bowl. The lights will ash on to indicate the unit is ready to use.
4. Press the I (low) or II (high) speed button on top of the motor housing.
5. Allow the chopper to work through the chopping process. Do not shake or move the chopper while operating.
6. When chopping has nished, release the speed button and the unit will stop.
7. Ensure the blade has completely stopped before removing the motor housing and chopper collar.
8. Remove the chopping blade by grasping the shaft rmly and lift up. Be careful, the blades are sharp!
9. After the chopping blade has been removed the ingredients can be removed from the chopping bowl.
10
10. Do not use the chopper for longer than 1 minute continuously. After 1 minute of continuous use, the unit may become over-heated.
Allow the unit to rest for at least 5 min before resuming use.
11. The lights will extinguish as the battery life reduces. A fully charged unit will show all three lights. When only the lowest light is
illuminated and ashing, this incidates that the unit needs to be charged.
If food becomes lodged around the blender blade or chopping blade during use:
1. Release the speed button and wait for the blades to stop.
2. Remove the motor housing and collar.
3. Use a spatula to carefully dislodge the food. Do not use ngers as the blades are sharp.
4. After the food has been removed and blades are clear, reassemble the collar and motor housing and continue use.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Licuadora de Tru
