Triton Blue WALLY 3715Z Manual de usuario

PROFESSIONAL MOVING HEAD USER MANUAL

WALLY 3715Z

KEEP THIS MANUAL FOR FUTURE NEEDS

XM787-V1.0.0-NR

Contents

1. Features .............................................................................................................................................................2

2. Fixture Overview ..............................................................................................................................................3

3. SAFETY INSTRUCTIONS .............................................................................................................................3

3.1) Important safety warns.........................................................................................................................3

3.2) GENERAL GUIDELINES ...................................................................................................................4

4. INSTALLATION INSTRUCTIONS ..............................................................................................................5

4.1) Mounting the device ..............................................................................................................................5

5. DMX-512 control connection...........................................................................................................................8

6. DMX-512 connection with DMX terminator .................................................................................................9

7. Projector DMX start address selection...........................................................................................................9

8. Control Board .................................................................................................................................................10

8.1 FUNCTION ...........................................................................................................................................11

8.1.1 Set DMX Address ......................................................................................................................11

8.1.2 Dmx Value ..................................................................................................................................12

8.1.3 Slave Mode .................................................................................................................................12

8.1.4 Auto Program.............................................................................................................................12

8.1.5 Sound Control ............................................................................................................................12

8.2 Information ............................................................................................................................................12

8.2.1 Time information .......................................................................................................................12

8.2.2 Temperature Info.......................................................................................................................14

8.2.3 Software Ver...............................................................................................................................14

8.3 PERSONALITY .....................................................................................................................................14

8.3.1 Status settings.............................................................................................................................14

8.3.2 Service setting.............................................................................................................................16

8.3.3 Fans Control...............................................................................................................................17

8.3.4 Display setting ............................................................................................................................17

8.3.5 Temperature C/F .......................................................................................................................18

8.3.6 Initial Status ...............................................................................................................................18

8.3.7 Reset Default ..............................................................................................................................18

8.4 Reset Function .......................................................................................................................................18

8.5 Effect Adjust...........................................................................................................................................19

8.5.1 Test channel................................................................................................................................19

8.5.2 Manual control...........................................................................................................................19

8.5.3 Calibration..................................................................................................................................19

8.6 Users mode set........................................................................................................................................19

8.6.1 User mode ...................................................................................................................................19

8.6.2 Edit User Mode ..........................................................................................................................19

8.7 Edit program ..........................................................................................................................................20

8.7.1 Select programs..........................................................................................................................20

8.7.2 Edit program..............................................................................................................................20

8.7.3 Edit scenes ..................................................................................................................................20

8.7.4 Rec. Controller...........................................................................................................................20

9. INSTRUCTIONS ON USE:...........................................................................................................................22

10. ERROR MESSAGE .....................................................................................................................................26

11. CLEANING AND MAINTENANCE .........................................................................................................27

12. TECHNICAL SPECIFICATIONS .............................................................................................................27

XM787-V1.0.0-NR

Thank you for your patronage. We are confident that our excellent products and service can

satisfy you. For your own safety, please read this user manual carefully before installing the

device.

In order to install , operate, and maintain the lighting safety and correctly. We suggest that the

installation and operation should be done by the verified technician and follow the instruction

strictly.

Every person involved with the installation, operation and maintenance of this device has to:

-be qualified

-follow carefully the instructions of this manual

INTRODUCTION:

Thank you for having chosen this professional moving head.

You will see you have acquired a powerful and versatile device.

Unpack the device. Inside the box you should find:

1. One XLR connection cable

2. Two omega clamps

3. One safety rope

4. Manual

5. One warranty card and certification

Please check carefully that there is no damage caused by transportation. Should there be any,

consult your dealer and don’t install this device.

1. Features

·37 x 15W high power LEDs

·Extremely Long Life:100,000 Hr and low power consumption

·3 DMX channel mode: 35/19/49 channels

·Pan/tilt movement: 8 bit and 16 bit resolution

For smooth and precise resolution

Pan: 540°/630° optional, Tilt: 265°movement

High speed of pan/tilt movement, speed of pan/tilt movement is adjustable

Scan position memory, auto reposition after unexpected movement

·Strobe effect with 18 flashes per second and pulse effect

·General dimming and blackout for all four colors

·Excellent color mixing and rainbow effect

·Display: Can be changed 180° reverse to fit for different installation position.

·Dimmer intensity from 0%~100%

·Control board with full color LCD graphic display and touch-keyboard

·Rechargeable Back up Battrty for Display

·Preset program: 7 built in programs can be called up via DMX controller

·Zoom: linear zoom

·Software-upload by optional accessory via DMX line

XM787-V1.0.0-NR

2. Fixture Overview

3. SAFETY INSTRUCTIONS

3.1) Important safety warns

This device has left the factory in perfect condition. In order to maintain this condition and to

ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and

warning notes written in this user manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The

dealer will not accept liability for any resulting defects or problems.

If the device has been exposed to temperature changes due to environmental changes, do not

switch it on immediately. The arising condensation could damage the device. Leave the device

switched off until it has reached room temperature.

1: Leds

2: Display

3: DC Switch

4: Microphone

5: Left-button

6: Down-button

7: Right-button

8: Mode/Esc-button

9: Up-button

10: ENTER-button

11: 3-Pin DMX in

12: 3-Pin DMX out

13: 5-Pin DMX in

14: 5-Pin DMX out

15: Fuse

16: Power supply

17: Power switch

18: Handle

XM787-V1.0.0-NR

This device falls under protection-class I. Therefore it is essential that the device be earthed.

If protection screen,lens or ultraviolet screen in the fixture is apparently damaged or is damaged

to exceed their own effective degree, such as cracked and gashed, it must be replaced.

The electric connection must carry out by qualified person.

Make sure that the available voltage is not higher than stated at the end of this manual.

Make sure the power cord is never crimped or damaged by sharp edges. If this would be the case,

replacement of the cable must be done by an authorized dealer.

Always disconnect from the mains, when the device is not in use or before cleaning it. Only

handle the power cord by the plug. Never pull out the plug by tugging the power cord.

During initial start-up some smoke or smell may arise. This is a normal process and does not

necessarily mean that the device is defective, it should decrease gradually.

Please don't project the beam onto combustible substances.

If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced

by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard.

Please be aware that damages caused by manual modifications to the device are not subject

to warranty. Keep away from children and non-professionals.

3.2) GENERAL GUIDELINES

This device is a lighting effect for professional use on stages, in discotheques, theatres, etc., the

device was designed for indoor use only.

This fixture is only allowed to be operated with the max alternating current which stated in the

technical specifications in the last page of this manual.

Lighting effects are not designed for permanent operation. Consistent operation breaks may

ensure that the device will serve you for a long time without defects.

Do not shake the device.Avoid brute force when installing or operating the device.

While choosing the installation-spot, please make sure that the device is not exposed to extreme

heat, moisture or dust. Please don't project the beam onto combustible substances.The minimum

distance between light-output from the projector and the illuminated surface must be more than

0.5 meter.

XM787-V1.0.0-NR

If you use the quick lock cam in hanging up the fixture, please make sure the quick lock fasteners

turned in the quick lock holes correctly.

Operate the device only after having familiarized with its functions. Do not permit operation by

persons not qualified for operating the device. Most damages are the result of unprofessional

operation.

Please use the original packaging if the device is to be transported.

For safety reasons, please be aware that all modifications on the device are forbidden.

If this device will be operated in any way different to the one described in this manual, the

product may suffer damages and the guarantee becomes void. Furthermore, any other operation

may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc.

4. INSTALLATION INSTRUCTIONS

Do not operate this device with open cover

4.1) Mounting the device

The applicable temperature for the lighting is between -10°C to 45°C. Do not use the lighting

under or above the temperature.

The installation of the effect has to be built and constructed in a way that it can hold 10 times the

weight for 1 hour without any harming deformation.

The installation must always be secured with a secondary safety attachment, e.g. an appropriate

safety rope.

Never stand directly below the device when mounting, removing or servicing the fixture.

The operator has to make sure the safety relating and machine technical installations are approved

by an expert before taking the device into operation for the first time.

These installations have to be approved by a skilled person once a year.

Overhead mounting requires extensive experience, including amongst others calculating

working load limits, installation material being used, and periodic safety inspection of all

installation material and the device. If you lack these qualifications, do not attempt the

installation yourself. Improper installation can result in bodily injury.

T h e$el ec tr i c $ c o n n ec ti o n $ m u s t$o n l y $ b e$ c a rri ed $o u t$ b y $ a$ q u al i f i ed $ el ec tr i c i a n .$

XM787-V1.0.0-NR

Before mounting make sure that the installation area can hold a minimum point load of 10 times the device’s

weight.

Connect the fixture to the mains with the power plug.

Installation via the Omega holders

a) Fixed the clamp on the bracket by tighten up the M12 screw on the bracket to the Ф13 hole in

the middle of the bracket.

b) Insert the quick-lock fasteners of the first Omega holder into the respective holes on the

bottom of the device. Tighten the quick-lock fasteners fully clockwise.

c) Install the second Omega holder.

d) Pull the safety-rope through the holes on the bottom of the base and over the trussing system

or a safe fixation spot. Insert the end in the carabine and tighten the safety screw.

Notice: this step is quite important to ensure that the fixture will not drop out by the

damage of the clamp.

XM787-V1.0.0-NR

Dimensional Drawings:

XM787-V1.0.0-NR

Layout Drawings:

Mounting points

Be sure this fixture is kept at least 0.5m away from any flammable materials (decoration etc.).

Always use and install the supplied safety cable as a safety measure to prevent accidental damage

and/or injury in the event the clamp fails.

Overhead mounting requires extensive experience, including amongst others calculating working

load limits, a fine knowledge of the installation material being used, and periodic safety

inspection of all installation material and the fixture. If you lack these qualifications, do not

attempt the installation yourself. Improper installation can result in bodily injury.

5. DMX-512 control connection

Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other

side to the male 3-pin XLR input of the moving head. You can chain multiple

Moving head together through serial linking. The cable needed should be two core, screened

cable with XLR input and output connectors. Please refer to the diagram below.

XM787-V1.0.0-NR

Address 1 Address 36 Address 71

6. DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically noisy

environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps in

preventing corruption of the digital control signal by electrical noise. The DMX terminator is

simply an XLR plug with a 120 Ωresistor connected between pins 2 and 3,which is then plugged

into the output XLR socket of the last fixture in the chain. Please see illustrations below.

7. Projector DMX start address selection

All fixtures should be given a DMX starting address when using a DMX signal, so that the

correct fixture responds to the correct control signals. This digital starting address is the channel

number from which the fixture starts to “listen” to the digital control information sent out from

the DMX controller. The allocation of this starting address is achieved by setting the correct

number on the display located on the base of the device.

You can set the same starting address for all fixtures or a group of fixtures, or make different

address for each fixture individually.

If you set the same address, all the units will start to “listen” to the same control signal from the

same channel number. In other words, changing the settings of one channel will affect all the

fixtures simultaneously.

If you set a different address, each unit will start to “listen” to the channel number you have set,

based on the quantity of control channels of the unit. That means changing the settings of one

channel will affect only the selected fixture.

In the case of the led move head, which is a 35 channel fixture, you should set the starting

address of the first unit to 1, the second unit to 36(35 + 1), the third unit to 71 (35+ 36), and so

on.

Tabla de contenidos

Otros manuales de Luminaria de Triton Blue

Triton Blue

Triton Blue 5R BEAM PRO Manual de usuario

Triton Blue

Triton Blue V700S-E Manual de usuario

Triton Blue

Triton Blue Q-WASH740Z Manual de usuario

Triton Blue

Triton Blue Q-BEAM200 Manual de usuario

Triton Blue

Triton Blue Q-BEAM200 Manual de usuario

Manuales populares de Luminaria de otras marcas

Emos

Emos CLASSIC ZY1431T Manual de usuario

Westinghouse

Westinghouse Outdoor Lighting Fixture Manual de usuario

Hedler

Hedler C 12 silent Manual de usuario

Blizzard Lighting

Blizzard Lighting Puck: CSI Manual de usuario

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Manual de usuario

Lightmaxx

Lightmaxx Shaft 5R Manual de usuario

Triarch

Triarch 31083 Manual de usuario

Philips

Philips 32614 Series Manual de usuario

IKEA

IKEA TIVED Manual de usuario

Lightolier

Lightolier LP200 Manual de usuario

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Manual de usuario

Martin

Martin MAC 250 Krypton Manual de usuario

Cooper Lighting

Cooper Lighting Halo L3232E Manual de usuario

Stageline

Stageline ODW-2410RGBW Manual de usuario

Light Sky

Light Sky Tornado Series Manual de usuario

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario

Lightolier

Lightolier Lytespan 83ED17S Manual de usuario

Lightolier

Lightolier Calculite CS8226 Manual de usuario