Tripp Lite SMART700DV Manual de usuario

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions 2

Quick Installation 3

Basic Operation 5

Storage and Service 8

SMART700DV

Intelligent, Line-Interactive UPS System

• 120V/230V Auto-Sensing Input, 120V Output

Not suitable for mobile applications.

Battery Replacement 9

Optional Installation 4

WARRANTY

REGISTRATION

to win a FREE Tripp Lite product!

www.tripplite.com/warranty

Specifications 10

Warranty Registration 10

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 1

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation, operation

and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty.

UPS Location Warnings

• The UPS is heavy. Use caution when lifting it.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near your UPS should be between 0° C and

40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its

vents or fan openings.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even

when the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug

in a way that would eliminate the UPS's connection to ground. Do not use adapters that

eliminate the UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

filtered, frequency-regulated computer-grade output. Connecting your UPS to a generator will

void its Ultimate Lifetime Insurance.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or

failure of a Tripp Lite UPS System could cause failure or significantly alter the performance

of a life-support device.

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or

batteries. Do not short or bridge the battery terminals with any object. Unplug and turn off the

UPS before performing battery replacement. Use tools with insulated handles. There are no

user-serviceable parts inside the UPS. Battery replacement should be performed only by

authorized service personnel using the same number and type of batteries (sealed Lead-Acid).

The batteries are recyclable. Refer to your local codes for disposal requirements or in the

USA only call 1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-822-8837) or visit

www.rbrc.com for recycling information. Tripp Lite offers a complete line of UPS System

Replacement Battery Cartridges (R.B.C.). Visit Tripp Lite on the Web at www.tripplite.com to

locate the specific replacement battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event of

a blackout or other power interruptions.

• Do not operate UPS without batteries.

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 2

Quick Installation

Plug the UPS into a wall outlet

supplying either 120V or 230V

(nominal) AC power.

Use the included detachable power cord. The IEC-320

end connects to the AC input receptacle on the rear of

the UPS; the NEMA 5-15 end connects to the wall

outlet.

To plug the UPS into a wall outlet that does not accept

a NEMA 5-15 plug, simply replace the included

power cord with a detachable cord from another piece

of equipment, such as a computer. Then, use the includ-

ed power cord to connect the equipment to the UPS.

NOTE! After you plug the UPS into a live AC outlet,

the UPS (in “Standby” mode) will automatically

charge its batteries,* but will not supply power to

its outlets until it is turned ON (see Step 3 below).

* The BATTERY CHARGE LED will be the only LED illuminated.

Plug your equipment into the UPS.

NOTE! Your UPS is designed to support only elec-

tronic equipment. You will overload the UPS if the

total VA ratings for all the equipment you connect

exceeds the UPS's Output Capacity (700VA). To find

your equipment's VA ratings, look on their name-

plates. If the equipment is listed in amps, multiply

the number of amps by 120 to determine VA.

(Example: 1 amp × 120 = 120 VA). If you are unsure if you have overloaded

the UPS's outlets, see “OUTPUT LOAD LEVEL” LED description.

Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY” button for

one second. The alarm will beep once briefly after one

second has passed. Release the button.

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 3

Optional Installation

These connections are optional. Your UPS will function

properly without these connections.

USB and RS-232 Serial

Communications

Use the included USB cable (see ) and/or DB9 serial

cable (see ) to connect the communication port on

your equipment to the communication port of your

UPS. Install on your equipment the Tripp Lite

PowerAlert Software appropriate to your equipment’s

operating system. Consult your PowerAlert manual

for more information.

EPO Port Connection

This optional feature is only for those applications

which require connection to a facility’s Emergency

Power Off (EPO) circuit. When the UPS is connected

to this circuit, it enables emergency shutdown of the

UPS’s inverter.

Using the cable provided, connect the EPO port of

your UPS (see ) to a user-supplied normally closed or

normally open switch according to the circuit diagram

(see ). The EPO port is not a phone line surge sup-

pressor; do not connect a phone line to this port.

4-5

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 4

“ON/OFF/STANDBY” Button

• To turn the UPS ON: with the UPS plugged into a live AC wall outlet*, press

and hold the “ON/OFF/STANDBY” button for one second.** Release the but-

ton. If utility power is absent, you can “cold-start” the UPS (i.e.: turn it ON and

supply power for a limited time from its batteries***) by pressing and holding

the “ON/OFF/STANDBY” button for one second.**

• To turn the UPS OFF: with the UPS ON and receiving utility power, press and

hold the “ON/OFF/STANDBY” button for one second.** Then unplug the UPS

from the wall outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS (in ”Standby” mode) will automatically charge

its batteries, but will not supply power to its outlets until it is turned ON. ** The alarm will beep once

briefly after the indicated interval has passed. *** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: briefly press and release the MUTE/TEST

button.*

To Run a Self-Test: with your UPS plugged in and turned ON, press and hold

the MUTE/TEST button for two seconds.* Continue holding the button until

the alarm beeps several times and the UPS performs a self-test. See “Results of

a Self-Test” below. Note: you can leave connected equipment on during a self-test.

Your UPS, however, will not perform a self-test if the UPS is not turned on (see

“ON/OFF/STANDBY” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues

to sound after the test, the UPS’s outlets are overloaded. To clear the overload,

unplug some of your equipment and run the self-test repeatedly until the

“OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no

longer sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease supplying

output power in the event of a blackout or brownout.

• If the “BATTERY WARNING” LED remains lit and the alarm continues

to sound after the test, the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and

repeat the self-test. If the LED remains lit, contact Tripp Lite for service.

If your UPS requires battery replacement, visit www.tripplite.com to

locate the specific Tripp Lite replacement battery for your UPS.

* The alarm will beep once briefly after the indicated interval has passed.

Basic Operation

Buttons (Front Panel)

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 5

Basic Operation

continued

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is plugged into a wall outlet

and turned ON.

“POWER” LED: this green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe

brownout. If the blackout or severe brownout is prolonged, you should save files

and shut down your equipment since internal battery power will eventually be

depleted. See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: this green LED lights continuously

whenever the UPS is automatically correcting high or low AC voltage on the

utility line without the assistance of battery power. The UPS will also emit a

slight clicking noise. These are normal, automatic operations of the UPS; no

action is required on your part.

“OUTPUT LOAD LEVEL” LED: this multicolored LED indicates the

approximate electrical load of equipment connected to the UPS's AC outlets. It

will turn from green (light load) to yellow (medium load) to red (overload). If

the LED is red (either illuminated continuously or flashing), clear the overload

immediately by unplugging some of your equipment from the outlets until the

LED changes from red to yellow (or green). CAUTION! Any overload that is not

corrected by the user immediately may cause the UPS to shut down and cease

supplying output power in the event of a blackout or brownout.

“BATTERY CHARGE” LED: when the UPS is operating from utility power,

this LED indicates the approximate charge state of the UPS's internal batteries:

red indicates the batteries are beginning to charge; yellow indicates the batteries

are roughly midway through charging; and green indicates the batteries are fully

charged. When the UPS is operating from battery power during a blackout or

severe brownout, this LED indicates the approximate amount of energy (ulti-

mately affecting runtime) which the UPS’s batteries will provide: red indicates

a low level of energy; yellow indicates a medium level of energy; and green

indicates a high level of energy. Since the runtime performance of all UPS bat-

teries will gradually deplete over time, it is recommended that you periodically

perform a self-test (see MUTE/TEST Button description) to determine the energy

level of your UPS batteries BEFORE a blackout or severe brownout occurs.

During a prolonged blackout or severe brownout, you should save files and shut

down your equipment since battery power will eventually be depleted. When the

LED turns red and an alarm sounds continuously, it indicates the UPS's batteries

are nearly out of power and UPS shutdown is imminent.

“BATTERY WARNING” LED: this LED lights red and an alarm sounds inter-

mittently after you initiate a self test (see “MUTE/TEST” Button description) to

indicate the UPS batteries need to be recharged or replaced. Allow the UPS to

recharge continuously for 12 hours, and repeat the self-test. If the LED contin-

ues to light, contact Tripp Lite for service. If your UPS requires battery replace-

ment, visit www.tripplite.com to locate the specific Tripp Lite replacement bat-

tery for your UPS.

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 6

Basic Operation

continued

Other UPS Features (Rear Panel)

15 amp/120V

NEMA 5-15R

AC Receptacles: Your UPS features 15-amp AC outlets. These output recep-

tacles, provide your connected equipment with AC line power during normal

operation and battery power during blackouts and brownouts. The UPS protects

equipment connected to these receptacles against damaging surges and line

noise. If you have a serial or USB connection to your UPS, you can remotely

reboot connected equipment by turning the receptacles OFF and ON using Tripp

Lite's PowerAlert Software.

Communications Ports (USB or RS-232): These ports connect your UPS to any

workstation or server. Use with Tripp Lite’s PowerAlert Software and included

cables to enable your computer to automatically save open files and shut down

equipment during a blackout. Also use PowerAlert Software to monitor a wide

variety of AC line power and UPS operating conditions. Consult your

PowerAlert Software manual or contact Tripp Lite Customer Support for more

information. See “USB and RS-232 Serial Communications” in the “Optional

Installation” section for installation instructions.

EPO (Emergency Power Off) Port: Your UPS features a EPO port that may

be used to connect the UPS to a contact closure switch to enable emergency

inverter shutdown. See Optional Installation.

Accessory Slot: Remove the small cover panel from this slot to install optional

accessories to remotely monitor and control your UPS. Refer to your accessory’s

manual for installation instructions. Contact Tripp Lite Customer Support at

(773) 869-1234 for more information, including a list of available SNMP, network

management and connectivity products.

Input Breaker: Protect your electrical circuit from overcurrent draw from

the UPS load. If this breaker trips, remove some of the load, then reset it by

pressing the breaker in.

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 7

Storage and Service

Storage

Before storing your UPS, turn it completely OFF: with the UPS ON and receiving utility power,

press and hold the "ON/OFF/STANDBY" button for one second (an alarm will beep once briefly

after the interval has passed); then, unplug the UPS from the wall outlet. If you store your UPS for

an extended period of time, recharge the UPS batteries once every three months: plug the UPS into

a wall outlet; allow it to charge for 12 hours; then unplug it and place it back in storage. Note: after

you plug the UPS in, it will automatically begin charging its batteries; however, it will not supply

power to its outlets (see Quick Installation section). If you leave your UPS batteries discharged for

an extended period of time, they will suffer a permanent loss of capacity.

Service

Before returning your UPS for service, follow these steps:

1. Review the installation and operation instructions in this manual to ensure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the UPS to the dealer. Instead, call Tripp Lite

at (773) 869-1233. A service technician will ask for the UPS's model number, serial number

and purchase date and will attempt to correct the problem over the phone.

3. If the problem requires service, the technician will issue you a Returned Material Authorization

(RMA) number, which is required for service. If you require packaging, the technician can

arrange to send you proper packaging. Securely pack the UPS to avoid damage during ship-

ping. Do not use Styrofoam beads for packaging. Any damages (direct, indirect, special, inci-

dental or consequential) to the UPS incurred during shipment to Tripp Lite or an authorized

Tripp Lite service center is not covered under warranty. UPS Systems shipped to Tripp Lite or

an authorized Tripp Lite service center must have transportation charges prepaid. Mark the

RMA number on the outside of the package. If the UPS System is within the 2-year warranty

period, enclose a copy of your sales receipt. Return the UPS for service using an insured car-

rier to the address given to you by the Tripp Lite service technician.

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 8

Battery Replacement

Under normal conditions, the original batteries in your UPS will last many years. See Safety

section before replacing batteries. The batteries are designed for hot-swap replacement (i.e. leaving the

UPS in ON mode), but some qualified service personnel may wish to put the UPS in the OFF mode

and disconnect equipment before proceeding.

Procedure

Remove Front Panel

Disconnect Batteries

Remove/Dispose of Batteries

Add Batteries

Connect Batteries

Attach connectors: black-to-black and red-to-red.

Replace Front Panel



200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 9

FCC RADIO/TV INTERFERENCE NOTICE:

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference when operated in a commercial environ-

ment. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the

instruction manual, may cause interference to radio communications. Operation of this equipment is likely to cause harmful interference in

which case the user will be required to correct the interference at his own expense. The user must use shielded cables and connectors with

this product. Any changes or modifications to this product not expressly approved by the party responsible for compliance could void the

user's authority to operate the equipment.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series

number. The series number can be found on the product nameplate label, along with all required approval markings and information.

When requesting compliance information for this product, always refer to the series number. The series number should not be con-

fused with the marking name or model number of the product.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

Specifications

Model: SMART700DV

Input Voltage: 120V or 230V AC (nominal), auto-sensing

Input Frequency: 50 or 60 Hz., auto-sensing

Input Receptacle: IEC-320-C14 (Accepts detachable power cords. Included

cord features NEMA 5-15 plug.)

Output Voltage: 120V AC

Output Frequency: 50 or 60 Hz.

Output Capacity (VA): 700

Output Capacity (Watts): 450

Output Receptacles: 6 NEMA 5-15R

Communications Ports: 1 USB, 1 RS-232

Emergency Power Off (EPO) Port: 1

The policy of Tripp Lite is one of continuous improvement. Specifications are subject to change without notice.

This product designed and engineered in the USA.

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product.

You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Warranty Registration

200511135 93-2513 SMART700DV OM.qxd 1/12/2006 3:28 PM Page 10

Otros manuales para SMART700DV

Tabla de contenidos

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite PRO550X Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750RTXLCD2U Manual de usuario

Tripp Lite

Tripp Lite BC Personal Datashield BCPERS300 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU5000RT4UTF Guía de configuración

Tripp Lite

Tripp Lite Internet Office & BC Personal UPS System Manual de usuario

Tripp Lite

Tripp Lite HT1000UPS Manual de usuario

Tripp Lite

Tripp Lite SmartOnLine SU2200RT2U-L520 Instrucciones de instalación y funcionamiento

Tripp Lite

Tripp Lite SmartPro SMART700USB Guía de configuración

Tripp Lite

Tripp Lite SmartPro SMX700HG Manual de usuario

Tripp Lite

Tripp Lite SMART1050SLTAA Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMC10002URM Manual de usuario

Tripp Lite

Tripp Lite Power Suppy Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750XL Manual de usuario

Tripp Lite

Tripp Lite SmartOnline Manual de usuario

Tripp Lite

Tripp Lite AGPS5542 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SUINT1000XLCD Manual de usuario

Tripp Lite

Tripp Lite INTERNET525 Manual de usuario

Tripp Lite

Tripp Lite SmartPro Rackmount SMX1000RT2U Guía de configuración

Tripp Lite

Tripp Lite SmartOnline Series Manual de usuario

Tripp Lite

Tripp Lite I Manual de usuario

Tripp Lite

Tripp Lite TE600 Manual de usuario

Tripp Lite

Tripp Lite OMNI1500LCDT Manual de usuario

Tripp Lite

Tripp Lite IO700NAFTA Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario