Tripp Lite AGSM5060 Manual de usuario

Owner’s Manual

SmartPro®Rack-Mount

Intelligent, Line-Interactive UPS Systems

• 120V Sine-Wave Input/Output* • 500VA - 3000VA Capacities

• Extended-Run Options

(Series Numbers: AGSM5060, AGSM8269, AG-0011, AG-0006, AG-0007)

* Except SMART500RT1U: sine-wave output on line; PWM output on battery.

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Important Safety Instructions 2

Mounting 4

Quick Installation 6

Optional Installation 7

Basic Operation 9

Storage and Service 13

Battery Replacement 14

Product Registration and Regulatory Compliance 15

Español 16

Français 32

17-06-249-932406.indb 1 6/20/2017 4:49:11 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed

these warnings will void your warranty.

UPS Location Warnings

• Use caution when lifting UPS. Because of the considerable weight of all Rack-mount UPS

systems, at least two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near your UPS should be between 0° C

and 40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct

its vents or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting

in this manner will seriously inhibit the unit’s internal cooling, eventually causing

product damage not covered under warranty.

UPS Connection Warnings

CAUTION: To reduce the risk of fire, connect only to a circuit provided branch circuit

overcurrent protection in accordance with the National Electrical Code, ANSI/NFPA 70

and the Canadian Electrical Code, Part I, C22.1. Short circuit backup protection

overcurrent protection is provided by the building installation. Be sure to use the proper

overcurrent protection for the installation in accordance with the plug/equipment rating.

• The UPS contains its own energy source (battery). The output terminals may be live even

when the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS plug

in a way that would eliminate the UPS's connection to ground. Do not use adapters that

eliminate the UPS connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must

provide filtered, frequency-regulated computer-grade output. Connecting your UPS to a

generator will void its Ultimate Lifetime Insurance.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to significantly

affect its safety or effectiveness is not recommended.

• Do not connect surge protectors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge protector and UPS warranties.

17-06-249-932406.indb 2 6/20/2017 4:49:11 PM

Important Safety Instructions

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS

or batteries. Do not short or bridge the battery terminals with any object. Unplug and turn

off the UPS before performing battery replacement. Use tools with insulated handles. There

are no user-serviceable parts inside the UPS. Battery replacement should be performed

only by authorized service personnel using the same number and type of batteries (sealed

Lead-Acid). The batteries are recyclable. Refer to your local codes for disposal

requirements or visit http://www.tripplite.com/support/recycling-program for recycling

information. Tripp Lite offers a complete line of UPS System Replacement Battery

Cartridges (R.B.C.).Visit Tripp Lite on the Web at http://www.tripplite.com/products/battery-

finder/ to locate the specific replacement battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event

of a blackout or other power interruptions.

• Do not operate UPS without batteries.

• When adding external battery packs to select models with external battery pack

connectors, connect only Tripp Lite-recommended battery packs of the correct voltage and

type. Do not connect or disconnect battery packs when the UPS is operating on battery

power.

17-06-249-932406.indb 3 6/20/2017 4:49:11 PM

Mounting (Rack)

Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for

2-post mounting). The user must determine the fitness of hardware and procedures before

mounting. If hardware and procedures are not suitable for your application, contact the

manufacturer of your rack or rack enclosure. The procedures described in this manual are for

common rack and rack enclosure types and may not be appropriate for all applications.

4-Post Mounting

All UPS models include hardware required to mount in a 4-post rack. Select models include

an adjustable rack-mount shelf kit to provide additional support. If your UPS model does

not include an adjustable rackmount shelf kit, skip steps 1 and 2.

1Connect the two segments of each shelf Ausing

the included screws and nuts B. Leave the

screws slightly loose so that the shelves can be

adjusted in the next step.

2Adjust each shelf to fit your rack, then mount

them in the lowest available space of your rack

with the screws, nuts and washers provided C.

Note that the support ledges should face inward.

Tighten the screws that connect the shelf

segments B.

3Attach mounting ears Dto the front mounting

holes of your equipment Eusing the screws

provided F. The ears should face forward.

4Using an assistant if necessary, lift your

equipment and slide it onto the mounting

shelves. Attach your equipment to the rack by

using the appropriate hardware Gthrough its

mounting ears and into the rack rails.

17-06-249-932406.indb 4 6/20/2017 4:49:12 PM

Mounting (Rack)

Mounting (Tower)

2-Post (Telecom) Mounting

Mount 1U UPS models in 2-post racks with included hardware following the procedure below.

If you mount 2U UPS models in 2-post racks, they require the addition of a Tripp Lite 2-Post

Rack-mount Installation Kit (model: 2POSTRMKITWM, sold separately). See Installation Kit

owner’s manual for installation procedure for 2U UPS models.

1Attach mounting ears Ato the front mounting

holes of your equipment Busing the screws

provided C. The ears should face backward.

2Using an assistant if necessary, lift your

equipment and slide it onto the mounting

shelves. Attach your equipment to the rack by

passing the screws, nuts and washers provided D

through its mounting ears and into the rack rails.

Mount all UPS models in an upright, tower position using included hardware. The user must

determine the fitness of hardware and procedures before mounting.

All UPS Models

Stand your UPS on its side with the LED/Control panel

at the top. Attach one rack mounting ear Ato each

side of the UPS using included screws B. Attach the

rack mounting ears to the floor with user-supplied

hardware.

2U UPS Models Only

Rotate the LED/Control panel to view it easier while

the UPS is tower mounted. Insert a small screwdriver,

or other tool, in the slots on either side of the panel.

Pry the panel from the UPS, rotate the panel

accordingly, and push the panel back into the UPS.

17-06-249-932406.indb 5 6/20/2017 4:49:13 PM

1Plug the UPS into an outlet on a

dedicated circuit.*

NOTE! after you plug the UPS into a live AC outlet, the

UPS (in “Standby” mode) will automatically charge its

batteries,** but will not supply power to its outlets until

it is turned ON (see Step 3 below).

* Select models include an additional plug which can

be switched by a qualified electrician. ** The BATTERY

CHARGE LED will be the only LED illuminated.

2Plug your equipment into the UPS.*

* Your UPS is designed to support only electronic

equipment. You will overload the UPS if the total VA

ratings for all the equipment you connect exceeds the

UPS's Output Capacity. To find your equipment's VA

ratings, look on their nameplates. If the equipment is

listed in amps, multiply the number of amps by 120 to

determine VA. (Example: 1 amp × 120 = 120 VA). If

you are unsure if you have overloaded the UPS's

outlets, see “OUTPUT LOAD LEVEL” LED description.

3Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY” button

for one second. The alarm will beep once briefly

after one second has passed. Release the

button.

SMART2200RMXL2U plug

(NEMA 5-20P) shown

SMART3000RM2U shown

Quick Installation

17-06-249-932406.indb 6 6/20/2017 4:49:14 PM

4-5

Optional Installation

These connections are optional. Your UPS will function properly without these

connections.

Note: SMART3000RM2U shown in all diagrams.

1USB and RS-232 Serial

Communications (all models)

Use the included USB cable 1a and/or DB9 serial

cable 1b to connect the communication port on

your computer to the communication port of your

UPS. Install on your computer the Tripp Lite

PowerAlert®Software appropriate to your

computer’s operating system. Your UPS may

feature additional communications ports; these

ports may also be connected to additional

computers which have PowerAlert Software

installed. Consult your PowerAlert manual for

more information.

2EPO Port Connection (all models)

This optional feature is only for those applications

which require connection to a facility’s Emergency

Power Off (EPO) circuit. When the UPS is

connected to this circuit, it enables emergency

shutdown of the UPS’s inverter.

Using the cable provided, connect the EPO port of

your UPS 2a to a user-supplied normally closed or

normally open switch according to the circuit

diagram 2b . The EPO port is not a phone line

surge protector; do not connect a phone line to

this port.

17-06-249-932406.indb 7 6/20/2017 4:49:14 PM

Optional Installation

3External Battery Connection

(select models only)

Your UPS comes with a robust internal battery

system; external batteries are needed only to

extend runtime. Adding external batteries will

increase recharge time as well as runtime.

The illustration 3a shows the location of your UPS

External Battery Connector, where you will insert

the battery pack cable. Complete installation

instructions for your battery pack appear in the

battery pack owner’s manual. Make sure that

cables are fully inserted into their connectors.

Small sparks may result during battery

connection; this is normal.

Do not connect or disconnect battery packs when

the UPS is running on battery power.

If you connect any external batteries, set the

Battery Charge Level Switch 3b to the down

position. This will increase your UPS charger

output so that the additional batteries charge

faster.

Note: The switch to the right of the Battery Charge Level

Switch is inactive and will not affect UPS operation

regardless of its position.

Caution! DO NOT set the Battery Charge Level

Switch to the down position without an

external battery connected. There is a risk of

damaging the UPS’s internal battery system.

17-06-249-932406.indb 8 6/20/2017 4:49:15 PM

Basic Operation

Buttons (Front Panel)

“ON/OFF/STANDBY” Button

• To turn the UPS ON: with the UPS plugged into a live AC wall outlet*,

press and hold the “ON/OFF/STANDBY” button for one second.** Release

the button. If utility power is absent, you can “cold-start” the UPS (i.e.:

turn it ON and supply power for a limited time from its batteries***) by

pressing and holding the “ON/OFF/STANDBY” button for one second.**

• To turn the UPS OFF: with the UPS ON and receiving utility power, press

and hold the “ON/OFF/STANDBY” button for one second.** Then unplug

the UPS from the wall outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS (in ”Standby” mode) will

automatically charge its batteries, but will not supply power to its outlets until it is

turned ON. ** The alarm will beep once briefly after the indicated interval has passed.

*** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: briefly press and release the MUTE/

TEST button.*

To Run a Self-Test: with your UPS plugged in and turned ON, press and

hold the MUTE/TEST button for two seconds.* Continue holding the button

until the alarm beeps several times and the UPS performs a self test. See

“Results of a Self-Test” below.

Note: you can leave connected equipment on during a self-test. Your UPS, however,

will not perform a self-test if the UPS is not turned on (see “ON/OFF/STANDBY” Button

description).

CAUTION! Do not unplug your UPS to test its batteries. This will

remove safe electrical grounding and may introduce a damaging

surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED continues to illuminate red and the

alarm continues to sound after the test, the UPS outlets are overloaded.

To clear the overload, unplug some of your equipment and run the self-

test repeatedly until the “OUTPUT LOAD LEVEL” LED no longer illuminates

red and the alarm no longer sounds.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease

supplying output power in the event of a blackout or brownout.

• If the “BATTERY WARNING” LED remains illuminated and the alarm

continues to sound after the test, the UPS batteries need to be recharged

or replaced. Allow the UPS to recharge continuously for 12 hours, and

repeat the self-test. If the LED remains illuminated, contact Tripp Lite for

service. If your UPS requires battery replacement, visit www.tripplite.com

to locate the specific Tripp Lite replacement battery for your UPS.

* The alarm will beep once briefly after the indicated interval has passed.

17-06-249-932406.indb 9 6/20/2017 4:49:15 PM

Basic Operation

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is plugged into a wall outlet and turned

ON.

“POWER” LED: this green LED illuminates continuously when the UPS is ON

and supplying connected equipment with AC power from a utility source. The

LED flashes and an alarm sounds (4 short beeps followed by a pause) to

indicate the UPS is operating from its internal batteries during a blackout or

severe brownout. If the blackout or severe brownout is prolonged, you

should save files and shut down your equipment since internal battery power

will eventually be depleted. See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: this green LED illuminates continuously

whenever the UPS is automatically correcting high or low AC voltage on the

utility line without the assistance of battery power. The UPS will also emit a

slight clicking noise. These are normal, automatic operations of the UPS; no

action is required on your part.

“OUTPUT LOAD LEVEL” LED: this multicolored LED indicates the

approximate electrical load of equipment connected to the UPS's AC

outlets. It will turn from green (light load) to yellow (medium load) to red

(overload). If the LED is red (either illuminated continuously or flashing),

clear the overload immediately by unplugging some of your equipment from

the outlets until the LED changes from red to yellow (or green). CAUTION!

Any overload that is not corrected by the user immediately may cause the

UPS to shut down and cease supplying output power in the event of a

blackout or brownout.

“BATTERY CHARGE” LED: when the UPS is operating from utility power,

this LED indicates the approximate charge state of the UPS internal

batteries: red indicates the batteries are beginning to charge; yellow

indicates the batteries are roughly midway through charging; and green

indicates the batteries are fully charged. When the UPS is operating from

battery power during a blackout or severe brownout, this LED indicates the

approximate amount of energy (ultimately affecting runtime) which the

UPS’s batteries will provide: red indicates a low level of energy; yellow

indicates a medium level of energy; and green indicates a high level of

energy. Since the runtime performance of all UPS batteries will gradually

deplete over time, it is recommended that you periodically perform a self-

test (see MUTE/TEST Button description) to determine the energy level of

your UPS batteries BEFORE a blackout or severe brownout occurs. During a

prolonged blackout or severe brownout, you should save files and shut

down your equipment since battery power will eventually be depleted. When

the LED turns red and an alarm sounds continuously, it indicates the UPS

batteries are nearly out of power and UPS shut down is imminent.

“BATTERY WARNING” LED: this LED illuminates red and an alarm sounds

intermittently after you initiate a self test (See “MUTE/TEST” Button

description) to indicate the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and repeat the self-

test. If the LED continues to light, contact Tripp Lite for service. If your UPS

requires battery replacement, visit www.tripplite.com to locate the specific

Tripp Lite replacement battery for your UPS.

17-06-249-932406.indb 10 6/20/2017 4:49:15 PM

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite SmartOnline SU80K Manual de usuario

Tripp Lite

Tripp Lite Internet Office & BC Personal UPS System Manual de usuario

Tripp Lite

Tripp Lite Line-Interactive UPS System SMART750USB Manual de usuario

Tripp Lite

Tripp Lite DCOW 2 Manual de usuario

Tripp Lite

Tripp Lite SmartPro Datacenter INT Manual de usuario

Tripp Lite

Tripp Lite AVR Series Manual de usuario

Tripp Lite

Tripp Lite RBC49-2U Manual de usuario

Tripp Lite

Tripp Lite SmartPro Rackmount SMX500RT1U Manual de usuario

Tripp Lite

Tripp Lite SMART 2200 NET Manual de usuario

Tripp Lite

Tripp Lite 500 VA Manual de usuario

Tripp Lite

Tripp Lite S750UNAFTA Manual de usuario

Tripp Lite

Tripp Lite ECO-UPS ECO650LCD Manual de usuario

Tripp Lite

Tripp Lite OmniPro 675 Manual de usuario

Tripp Lite

Tripp Lite SU10000RT3UG Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART1500RM2U Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART500RT1U Manual de usuario

Tripp Lite

Tripp Lite SmartPro 700 HG Instrucciones de instalación y funcionamiento

Tripp Lite

Tripp Lite PRO550X Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART3000RMXL2U Guía de instalación

Tripp Lite

Tripp Lite AGSM7499 Manual de usuario

Tripp Lite

Tripp Lite SM1500RMXL2UTAA Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU40K Manual de usuario

Tripp Lite

Tripp Lite SMART1000LCDTAA Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU10KRT3/1X Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario