Tripp Lite PDU3XMV6G32 Manual de usuario

Owner’s Manual

3-Phase Metered 0U

Power Distribution Unit

(Phase and Bank Measurements)

PDU3XMV6G32

(Series Number: AG-00BD)

Important Safety Instructions 2

Installation 3

Digital Display 5

Using the Digital Display 6

Features 12

Service 13

Warranty and 14

Product Registration

Español 15

Français 29

Русский 43

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

14-08-206-93338E.indb 1 10/9/2014 11:31:48 AM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• The PDU provides the convenience of multiple outlets, but DOES NOT provide surge or line

noise protection for connected equipment.

• The PDU is designed for indoor use only, in a controlled environment, away from excess

moisture, temperature extremes, conductive contaminants, dust or direct sunlight.

• Keep indoor ambient temperature between 32°F and 122°F (0°C and 50°C).

• The PDU must be installed by a qualiﬁed technician only.

• Do not attempt to mount the PDU to an insecure or unstable surface.

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Connect the PDU to an outlet that is in accordance with your local building codes and that is

adequately protected against excess currents, short circuits and earth faults.

• The electrical outlets supplying power to the equipment should be installed near the equipment

and easily accessible.

• Do not connect the PDU to an ungrounded outlet or to extension cords or adapters that

eliminate the connection to ground.

• Be sure to provide a local disconnect device on any models that are permanently installed

without a plug that is easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Individual equipment connected to the PDU should not draw more current than the individual

PDU’s outlet’s rating.

• The total load connected to the PDU must not exceed the maximum load rating for the PDU.

• Do not attempt to modify the PDU, input plugs or power cables.

• Do not drill into or attempt to open any part of the PDU housing. There are no user-serviceable

parts inside.

• Do not attempt to use the PDU if any part of it becomes damaged.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to signiﬁcantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a ﬂammable anesthetic mixture with air, oxygen or nitrous oxide.

14-08-206-93338E.indb 2 10/9/2014 11:31:48 AM

1-5

1-1

1-6

1-5

1-2 1-3 1-4

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets to the PDU are included. Use only the screws

supplied by the manufacturer or their exact equivalent.

Note: Mounting buttons come preinstalled to the PDU for toolless mounting.

1-1 To mount the PDU using the pre-installed

mounting buttons, position the PDU as

desired in the rack enclosure, align the

buttons with the rack mounting slots,

and slide the PDU into position.

1-2 To attach the mounting brackets to the

PDU, remove the mounting buttons.

1-3 Attach the mounting brackets to the

PDU with the included screws.

1-4 Attach the PDU to a vertical rail in

your rack or rack enclosure. (Use the

mounting hardware that came with your

rack or rack enclosure to attach the

mounting brackets to the rail.)

1-5 To reinstall the mounting buttons for

toolless mounting, remove the mounting

brackets then install the mounting

buttons onto the PDU.

Note: Be sure to insert the 2 buttons into either

the upper hole at each end of the PDU or into

the lower hole at each end of the PDU.

1-6 To install the PDU with its outlets facing

the rear of the rack, use the included

PDUMVROTATEBRKT accessory. First,

attach the mounting button Ato the

V-shaped bracket Busing the included

screw and washer. Then, use the

button-mount slot to attach the bracket

to the PDU and the mounting button to

attach the PDU to the rack. The bracket

effectively repositions the mounting

brackets allowing for the PDU outlets to

face the rear of the rack.

14-08-206-93338E.indb 3 10/9/2014 11:31:50 AM

L3-N BANK 3L2-N BANK 2L1-N BANK 1

L1-N BANK 1

L2-N BANK 2

L3-N BANK 3

L1-N BANK 4

2-2

2-3

2-4

Installation

Connecting the PDU

2-1 The PDU3XMV6G32 is equipped with a 32A Red IEC 309 3P + N + E plug.

Model Name Input Plug

Max Input

Amps (Limited

by Input Cord

and Plug)

Input

Voltage

Range

Output

Voltage

Range Breakers

Cord

Length Outlets

PDU3XMV6G32 32A Red IEC 309

3P + N + E 32A 360-415V 208-240V 6 x Single

Pole, 20A

Branch-Rated

6 ft.

(1.8 m)

42 Total: 6 Banks

of (1) C19 and

(6) C13

2-2 Connect the input plug to your facility’s

compatible AC power source.

2-3 Connect your equipment’s input plugs to

the appropriate outlets on the PDU. The

LED near each bank illuminates when

the bank is ready to distribute live

AC power.

Note: It is recommended that you do not

connect a live load to the PDU. If the load you

intend to connect has an ON/OFF switch, please

turn the switch to OFF prior to connection.

2-4 Optional Cord Retention Procedure

Use the included C14 and C20 plastic

sleeves to secure plugs to receptacles.

Attach the sleeve to the plug, making

sure that the pull tabs Aremain outside

the plug and that the ﬁt is secure. To

unplug equipment properly, use the pull

tabs to remove the plug and sleeve from

the receptacle.

14-08-206-93338E.indb 4 10/9/2014 11:31:51 AM

BC DE

Digital Display

A3-Digit Display: Shows measured or calculated values such as Amperage, Kilowatts,

Voltage and Power Unbalance Percentage.

BArrow Buttons: Scroll through indicated Input, Bank, Power, Load Balance and Display

Brightness options using these buttons. A long press of the up or down arrow buttons allows

the user to skip to the next sequential measurement category.

CMode Button: When a menu option is selected using the Arrow Buttons, the Mode Button

scrolls through the sub-options within each category. Sub-options are shown by the

Indicator LEDs.

DIndicator LEDs: Lit LED indicates which value is being displayed on the 3-digit screen.

Amps (A): When selected, the load on the selected Input Phase (L#) or

Load Bank (B#) is displayed in amps.

Wattage (kW): When selected, the load on the selected Load Bank (B#) or

Total Output Power (OP) is displayed in kW.

Voltage (V): Input Phase (L#) or Load Bank (B#) voltage is displayed.

Unbalanced Load (%UB): When lit, the display shows the unbalanced load

percentage deviance from the average measured value. A value that is zero or closest

to zero is desirable.

E2-Digit Display: This display indicates which Input Phase (L#), Load Unbalance (UB),

Load Bank (B#) or Output Power (OP) option is selected.

Button Response Deﬁnitions:

Switch Action Control Function

Pushbutton

Depress ½ sec Sequentially, moves up one selection in the menu.

Depress 3 sec Advances up to the next measurement category.

Down

Pushbutton

Depress ½ sec Sequentially, moves down one selection in the menu.

Depress 3 sec Advances down to the next measurement category.

Mode

Pushbutton

Depress ½ sec Displays available options for a given measurement category.

Depress 3 sec Selects the chosen available option for a given conﬁguration category.

14-08-206-93338E.indb 5 10/9/2014 11:31:51 AM

L3-N BANK 6L2-N BANK 5L1-N BANK 4L3-N BANK 3L2-N BANK 2L1-NBANK 1

L1-NBANK 1

L2-NBANK 2

L3-NBANK 3

L1-NBANK 4

L2-NBANK 5

L3-NBANK 6

FactoryUse Only

L1-N L1-NL3-N L3-NL2-N L2-N

i 5.5

L i

i 5.5

L 2

i 5.5

L 3

4 0 0

L i

4 0 0

L 2

4 0 0

L 3

Digital Display

Load Bank Receptacle Location and Display References

PDU3XMV6G32

MODEL SILKSCREEN LABEL DESCRIPTION 2-DIGIT DISPLAY REFERENCE

PDU3XMV6G32 L1-N (Bank 1) B1

L2-N (Bank 2) B2

L3-N (Bank 3) B3

L1-N (Bank 4) B4

L2-N (Bank 5) B5

L3-N (Bank 6) B6

INPUT PHASE REFERENCE

INPUT PHASE REPORTED 2-DIGIT DISPLAY REFERENCE

L1-N L1

L2-N L2

L3-N L3

Using the Digital Display

Scrolling Through Input Phases and Options

(Measurement Category)

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Input Phase 2

Input Phase 1

Amps Volts* * Note: Voltages displayed are

phase-to-phase voltages (i.e.,

L1 display will indicate L1-L2

voltage).

14-08-206-93338E.indb 6 10/9/2014 11:31:52 AM

2 0

i 5.5

L i

i 5.5

L 2

i 5.5

L 3

4 0 0

L i

4 0 0

L 2

4 0 0

L 3

Using the Digital Display

Phase Imbalance %

Unbalanced Load Detect (Measurement Category)

Input Phase 2

Amps Volts*

Input Phase 3

Amps Volts*

To Unbalanced Load Detect

14-08-206-93338E.indb 7 10/9/2014 11:31:52 AM

1 0 .5

2. 1 8

2 0 8

1 0 .5

2. 1 8

2 0 8

1 0 .5

2. 1 8

2 0 8

Using the Digital Display

Scrolling Through Load Banks and Options (Measurement Category)

Scroll through the parameter display for each Load Bank using Mode and buttons.

Amps

Kilowatts

Volts

Bank #2

Bank #3

To Total

Output

Power

Amps Kilowatts Volts

Note: Continue for Load Banks 4-6.

14-08-206-93338E.indb 8 10/9/2014 11:31:53 AM

i.2 3

I 2

Using the Digital Display

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Total Output Power (Measurement Category)

Kilowatts

To Scroll

Function

Options

Press Mode button to toggle between options and data within a menu. A momentary press of the

arrow buttons switches between menus. A long press skips between measurement categories.

The scrolling pattern of the display is outlined below.

Scroll Function Options (Conﬁguration Category)

When enabled, the Auto Scroll function displays data for Input Phases, Load Unbalance and Load

Banks in 4-second intervals. Y indicates the function is enabled; N indicates that it is disabled.

Pressing any button interrupts the auto scroll function, allowing the user to navigate between

menu options. If no button is pressed, there is a 10 second timeout.

Note: Hold Mode button for 3 seconds to switch between options. The letter in the 2-digit display indicates the

selected option.

To LED

Brightness

14-08-206-93338E.indb 9 10/9/2014 11:31:54 AM

I 2

Using the Digital Display

LED Brightness and Color Scheme (Conﬁguration Category)

Hold the Mode button for 3 seconds to scroll through each option. The number in the 2-digit

display is deﬁned as: 1=25%; 2=50%; 3=75%; 4=100%

Bank Indicator LED Color Code Options (Conﬁguration Category)

Hold the Mode button for 3 seconds to switch between options.

The number in the 2-digit display indicates the selected scheme.

1=Standard, 2=Alternate

14-08-206-93338E.indb 10 10/9/2014 11:31:54 AM

Tabla de contenidos

Idiomas:

Otros manuales de Unidad de distribución de energía de Tripp Lite

Tripp Lite

Tripp Lite Metered Rack PDU Manual de usuario

Tripp Lite

Tripp Lite PDU3VSR6H50A Manual de usuario

Tripp Lite

Tripp Lite PDUMV30HV2 Manual de usuario

Tripp Lite

Tripp Lite PDUNV Manual de usuario

Tripp Lite

Tripp Lite SUPDMB6KHW Manual de usuario

Tripp Lite

Tripp Lite PDUMNH15 Manual de usuario

Tripp Lite

Tripp Lite PDUMNV20/NET Manual de usuario

Tripp Lite

Tripp Lite SUPDM Modules 932645 932645 Manual de usuario

Tripp Lite

Tripp Lite SUDC Series Manual de usuario

Tripp Lite

Tripp Lite PDUMV40 Manual de usuario

Tripp Lite

Tripp Lite PDUMH15ATNET Manual de usuario

Tripp Lite

Tripp Lite PDUMH20NET2 Guía de configuración

Tripp Lite

Tripp Lite PDUMV15 Manual de usuario

Tripp Lite

Tripp Lite PDU3EVN10L2130 Manual de usuario

Tripp Lite

Tripp Lite PDUV30HV Manual de usuario

Tripp Lite

Tripp Lite PDUMV15NET Manual de usuario

Tripp Lite

Tripp Lite PDUMH30NET Manual de usuario

Tripp Lite

Tripp Lite PDUMV32HVNET Manual de usuario

Tripp Lite

Tripp Lite PDUMV40 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline B020-016 6 Manual de usuario

Tripp Lite

Tripp Lite PDUMV30HVNET Manual de usuario

Tripp Lite

Tripp Lite PDUMNV30HVLX Manual de usuario

Tripp Lite

Tripp Lite PDUMH15AT Manual de usuario

Tripp Lite

Tripp Lite PDUNV Manual de usuario

Manuales populares de Unidad de distribución de energía de otras marcas

hager

hager SP 015 Manual de usuario

Pakedge

Pakedge PowerPak 9 Manual de usuario

Pts

Pts 9042 Series Manual de usuario

Shure

Shure WA405 Manual de usuario

CORNING

CORNING CCH 4U Manual de usuario

Panamax

Panamax M4LT-EX Manual de usuario

PANCONNECT

PANCONNECT FLAT 3M Manual de usuario

Raytheon

Raytheon 138-118 Manual de usuario

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Manual de usuario

Botex

Botex PSA 322-6 DL Manual de usuario

GE QuiXtra 4000 Guía de inicio rápido

RDL

RDL EZ Series Manual de usuario

StarTech.com

StarTech.com RKPW161915 Manual del sistema

Vertiv

Vertiv Knürr DI-Strip Rack PDU Manual de usuario

ABB

ABB PSBS0065 Manual

Baumuller

Baumuller BFN 3-1-0007-001 Manual

Eaton

Eaton StructuredWiringSolutions ESWT41600 Manual

GE GEK-45404F Manual de usuario