Triplett TMP50 Manual de usuario

User Manual

TMP50

Type K/J Thermometer

Introduction

Congratulations on your purchase of the Triplett TMP50 Type K/J

Thermometer This meter. This single input contact thermometer offers fast

response and laboratory accuracy and works with K-type or J-type

thermocouples as temperature sensors and offers a 0.1 0C/0.1 0 F resolution.

Safety

Do not operate the meter in environments where the following are

present: explosive gases (or materials), combustible gases (or

materials), steam, or dust.

Please replace the battery immediately when the low battery symbol

appears on the LCD.

Do not touch the meter’s circuit board for any reason; static

electricity or contamination could damage the sensitive

components.

This instrument was designed for pollution

degree 2. Operation Altitude: Up to 2000m

(7000’).

Description

1. Type K Thermocouple Input

2.LCD Display

3.Function Buttons

4.Power: ON/OFF Button

Display

1. Entering/Exiting Setup Icon

2. Offset Option Icon

3. HOLD Icon

4. APO Status Icon

5. Primary Display: T1 Reading

6. Units Icon

7. Secondary Display –

MAX/MIN/AVG/OFFSET

8. MIN/MAX/AVG Icon

9. Time Display

10. Min: Sec or Hour: min

Display

11. Thermocouple Type Icon

12. Low Battery Indicator Icon

Operation

Connecting thermocouples

1. This meter accepts a K/J-type thermocouple with spade lugs (sub-

miniature type with one spade wider than the other).

2. Plug the thermocouple into the meter's thermocouple input jack.

Measuring

1. Press the button to switch ON the thermometer on. After 1

second the thermometer will display the first temperature reading

(upper display).

2. Press the C-F-K button to select the desired temperature unit of

measure. A display icon will reflect the selection.

3. Touch the object to be measured with the probe. Read the

measured temperature on the display.

Note: If the display indicates “OL” the temperature is outside the

measurement range. The display shows "- - - -" when a

thermocouple is not connected.

MAX/MIN/AVG mode

Press MAX/MIN to capture and step through the maximum (MAX),

minimum (MIN) and average (AVG) temperature values. These values will

be shown in the lower display with an elapsed time reference below

(hrs:mins, mins:secs).

1. Press MAX/MIN to enter this mode.

2. Press MAX/MIN to step through maximum, minimum and average

readings.

3. Press and hold MAX/MIN for 3 seconds to return to normal mode.

Data Hold

Press the HOLD button to freeze the reading in the display. HOLD will

appear at the top right of the display. Press the HOLD button again to

return to normal operation mode.

Backlight

Press the SETUP button to switch the backlight OFF/ON.

Setup option

The setup option is used to select the thermocouple type that matches the type

that will be connected to the meter, to switch the sleep mode OFF/ON, and to

adjust the thermocouple offset.

Note: In the setup mode, the upper display shows the menu items and

the lower display shows the selection for a given menu item.

Press and hold the SET button for 3 seconds to enter or exit the

Setup mode. When the thermometer is in Setup mode, the

display shows the SETUP display icon.

Set Type J or K thermocouple

1. Press ▲or ▼to scroll to the “TYPE” setting (shown on the bottom left

of the display).

2. Press ENTER to choose the option.

3. Press ▼to toggle between J and K.

4. Press and hold the SET button for 3 seconds to save the setting and

return to normal mode.

Set Sleep/Non-sleep mode

The thermometer enters sleep mode by default. The meter will

automatically shut off after 20 minutes of inactivity (no buttons pressed).

When the thermometer is in Setup mode, the display shows the SETUP

display icon.

1. Press ▲or ▼to scroll to the SLP setting.

2. Press ENTER to choose the option; On or OFF will appear in the

display.

3. Use the arrow key ▼to select ON or OFF.

4. Press ENTER to store the new setting.

5. Press and hold the SET button for 3 seconds to return to normal

mode.

Set Offset

Use the offset option in Setup (T1 menu item) to adjust the

thermometer’s readings to compensate for known temperature offset at

a specific temperature. The adjustment range is ± 5.0°C or ± 9.0 °F.

1. Plug the thermocouple into the input connector.

2. Place the thermocouple into the known, stable temperature

environment (such as an ice bath or dry well calibrator). Allow the

reading to stabilize.

3. Use the arrow keys ▲ ▼ to scroll to the “T1”option and then press

ENTER.

4. Change the offset temperature reading (upper display) by

pressing ▼until the desired temperature is reached.

5. Press and hold the SET button for 3 seconds to return to normal

mode.

Replacing the Batteries

1. Switch OFF the thermometer.

2. Loosen the battery compartment screw and remove the compartment

door.

3. Replace the AAA batteries.

4. Replace the battery door and tighten the screw.

Never dispose of used batteries or rechargeable batteries

in household waste. As consumers, users are legally

required to take used batteries to appropriate collection

sites, the retail store where the batteries were purchased,

or wherever batteries are sold.

Disposal: Do not dispose of this instrument in household waste. The user is

obligated to take end-of-life devices to a designated collection point for the

disposal of electrical and electronic equipment.

Other Battery Safety Reminders

oNever dispose of batteries in a fire. Batteries may explode or leak.

•Never mix battery types. Always install new batteries of the same type.

Specifications

Temperature Range:

K type thermocouples -200°C to 1372°C (-328°F to 2501°F)

J type thermocouples -210°C to 1100°C (-346°F to 2012°F)

Note that thermocouple wire may be insulated with materials that cannot

withstand temperatures in the ranges listed above. Check that the

thermocouples used are rated for the temperature measurements to be

made.

Temperature accuracy:

Above –100 °C (-148 °F)

± [0.15%rgd+1°C (1.8°F)]

Below –100 °C (-148 °F)

± [0.5%rgd+2°C (3.6°F)]

Display Resolution:

0.1°C /°F /°K <1000, 1°C /°F /°K >1000

Power supply:

Three (3) AAA 1.5V batteries

Operating Temperature:

0°C to 50°C (40°F to 122°F)

Storage Temperature:

10°C to 50°C (14°F to 122°F)

Dimensions:

220 x 63 x 28mm (8.7 x 2.5 x 1.1”)

Weight:

200g (7oz)

Warranty Information

Triplett / Jewell Instruments extends the following warranty to the original purchaser of

these goods for use. Triplett warrants to the original purchaser for use that the products sold

by it will be free from defects in workmanship and material for a period of (1) one year from

the date of purchase. This warranty does not apply to any of our products which have been

repaired or altered by unauthorized persons in any way or purchased from unauthorized

distributors so as, in our sole judgment, to injure their stability or reliability, or which have

been subject to misuse, abuse, misapplication, negligence, accident or which have had the

serial numbers altered, defaced, or removed. Accessories, including batteries are not

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Termómetro de Triplett

Triplett

Triplett RHT70 Manual de usuario

Triplett

Triplett TMP10 Manual de usuario

Triplett

Triplett IRT350 Manual de usuario

Triplett

Triplett CM675IR Manual de usuario

Triplett

Triplett IRT150 Manual de usuario

Triplett

Triplett FT2020 Manual de usuario

Triplett

Triplett RHT415-NIST Manual de usuario

Triplett

Triplett TMP10 Manual de usuario

Triplett

Triplett IRTUV50 Manual de usuario

Triplett

Triplett TPM10 Manual de usuario

Triplett

Triplett IRT500 Manual de usuario

Triplett

Triplett TMP15 Manual de usuario

Triplett

Triplett ProTemp PT12A Manual de usuario

Triplett

Triplett IRT220 Manual de usuario

Triplett

Triplett ProTemp 12 Manual de usuario

Triplett

Triplett RHT415 Manual de usuario

Triplett

Triplett TMP60 Manual de usuario

Triplett

Triplett TMP10 Manual de usuario

Triplett

Triplett ProTemp 6 Manual de usuario

Triplett

Triplett RHT12 Manual de usuario

Triplett

Triplett IRT227 Manual de usuario

Triplett

Triplett TMP60 Manual de usuario

Triplett

Triplett IRT225 Manual de usuario

Manuales populares de Termómetro de otras marcas

Delton

Delton 981A Manual de usuario

Baker

Baker MM2P Manual de usuario

Tarmo

Tarmo 320281 Manual de usuario

Citizen

Citizen CTD 504 Manual de usuario

TFA

TFA 14.1500 Manual de usuario

Vive

Vive DMD1010 Manual de usuario

Gotemp

Gotemp THB4002 Manual de usuario

GREISINGER

GREISINGER G 1202 Manual de usuario

Amprobe

Amprobe TMD-53W Manual de usuario

Trotec

Trotec BP10 Manual de usuario

Radiance instruments

Radiance instruments RT616 Series Manual de usuario

Eurolec

Eurolec IR151 Manual de usuario

Scaneo

Scaneo TS42B Manual de usuario

Sper scientific

Sper scientific 800043 Manual de usuario

Microlife

Microlife NC 200 Manual de instrucciones

Motorola

Motorola MBP69SN Guía de configuración

The MeatStick

The MeatStick The MeatStick Manual de usuario

Hama

Hama TH35-A Manual de usuario