Trinity NF29 Manual de usuario
TRACKSO INSTALLATION GUIDE FOR TRINITY NF29 METER
Brand: Trinity
Type: Multi-line Digital Display Panel Meter
Models: Trinity NF29 Meters
CONNECTION DIAGRAM
On the rear panel, Trinity NF29 Meters has an RS-485 communication socket as shown in the following figure.
Figure T1 –Rear view of Trinity NF29 Meter
1. Please unscrew the RS485 terminal as shown in Figure T1.
2. Connect the cables to the RS485 bus terminal blocks.
3. Please make the connections from Terminal Block chip to TrackSo IoT
Gateway as mentioned in the Table –TT1.
Table TT1 –Trinity NF29 Meter RS485 chip
connections with TrackSo IoT Gateway
Trinity NF29 Pin No. &
Assignment
TrackSo Pin No. &
Assignment
2
A
3
D+
1
B
4
D-
DEFAULT CONFIGURATION IN TRACKSO IOT GATEWAY
Inverter ID: 1 (Range: 1 to 247)
Baud Rate: 9600
Data Bits: 8
Stop Bit: 1
Parity: N/A (None)
CONFIGURATION AT THE METER END
Enter into programming mode to setup meter for communication
In order to operate for all the field programmable parameters, it is easy user interface by pressing the keys such as
keys. Once the unit displays CT PRIMARY, press key to move into the next programmable parameter, UNIT
ADDRESS for RS485 communication.
SETTING DEVICE ID
The unit has the provision to specify a meter address at site for RS485 port. This address can be set starting from 1 to 255 with a
fixed baud rate of 9600
To set the Device ID, proceed the following instruction:
1) Press key for about 4 to 5 seconds on Run Mode display.
2) The unit will enter into Programming Mode display with the settable parameter, unit ADDRESS such as shown below
.
3) Press key. Immediately, P starts blinking with an interval of one second which shows that the parameter is now
settable. Set the ADDRESS by using keys until the desired value is received and then, press key to
confirm the set value.
4) Now, the unit will reset and return into Run Mode.
NOTE: The above details are mentioned in the Installation & Operation Manual for Trinity NF29 Meter.
CONNECTING MULTIPLE METER
Set Unit Id (Modbus Address) as mentioned on
the TrackSo Device
TRACKSO WORKING
1. Insure correct connections as detailed in the installation guide.
2. Insert the SIM card.
3. Switch on the power to the TrackSo device. (Minimum 12V/1A input is required)
4. Power LED (Red) of TrackSo IoT gateway glows and stays ON.
NOTE: TrackSo IoT Gateway will only be able to send data if the GPRS network is available at the
installed location.
LED
NAME
DESCRIPTION
GREEN
POWER
Light when Power on the device
RED
GSM
LED Status
Connection State
Flashing (ON for 100ms and OFF for 100ms)
SIM Card not found
Flashing (ON for 500ms and OFF for 500ms)
Searching for GSM Network
Flashing (ON for 0.1s and OFF for 2.9s)
Once at every 3sec
GSM Network Registered
Flashing twice at every 3sec
GPRS IP Connected
Flashing 5times
GPRS IP Sending data
LED OFF
GSM Fault
GREEN
COM TX
Blink on data transmission in RS485 port
YELLOW
COM RX
Blink on data reception in RS485 port
5. To check the exact network status send the following message to mobile number of the device
SMS Command= *2222#<Stat.gsm>
IMEI
IMEI No. of the data logger (Device Key)
NW
Network
SIGN
Signal Strength out of 31
GPRS
CONT- connected , NC- not connected
PIP
Connected to TrackSo Server or not
CONT- connected, NC- not connected
LOG
no. of data points stored in devices incase of no interet
6. If the GSM light starts flashing 5 times then Login to www.trackso.in with your Username/Password.
7. Click on ‘Units’ from the menu bar. You will be able to view your installed unit in the table as shown
below.
8. Check if the Status becomes Receiveing for the relevant Unit.
9. If the state remains Not receiveing for more than 10 minutes, click on your email ID at the top right of the
screen and click on ‘Event Ingestion Logs’ in the dropdown.
10. Check if there is some log generated at the time of installation of the TrackSo IoT Gateway device.
a. If NO, please restart the device and try the same flow again.
b. If YES, email us at support @trackso.in to consult the same.
Tabla de contenidos
Otros manuales de Instrumento de medición de Trinity
Trinity
Trinity XPERT-PRO Manual de usuario
Trinity
Trinity TINYPRO6 Manual de usuario
Trinity
Trinity E3000 Series Manual de usuario
Trinity
Trinity TINYPRO3 Manual de usuario
Trinity
Trinity ENTITY Manual de usuario
Trinity
Trinity Olympus WS-811 Manual de usuario
Trinity
Trinity VAF Manual de usuario
Trinity
Trinity SLM102 Manual de usuario
Trinity
Trinity INFINITY Manual de usuario
Manuales populares de Instrumento de medición de otras marcas
Endress+Hauser
Endress+Hauser Proline Promag 50 Especificaciones técnicas
Siemens
Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas
KLINGER
KLINGER CMF V Series Manual de usuario
EXFO
EXFO FTB-2 Manual de operación y mantenimiento
Keysight
Keysight M8290A Manual de usuario
ADTEK
ADTEK MW-5 Manual de usuario