Triner Scale 7600 Manual de usuario

Version 2.0_12-15-19

Custom Bench Scale

Barcode Scanning and Label Printing:

Bench Scale Application

Operating Guide

Operating Guide | Custom Bench Scale

Table of Contents

Specifications

7600 Model Digital Indicator ............................................2

TBS-1616 Model Weighing Platform...............................2

Quick Start: Connecting, Powering On and Operating

Location of Use ..........................................................QS-1

Step by Step Connecting & Powering On ................QS-2

Connections Diagram................................................QS-3

Initialize the Bar Code Scanner ................................QS-4

Weigh, Scan & Print ..................................................QS-4

Trouble Shooting the System....................................QS-5

Keypad Keys Functions ........................................................3

Settings Menu, 7600 Digital Indicator .................................5

Error Codes, 7600 Digital Indicator......................................6

Operating Guide | Custom Bench Scale

Specifications

7600 Digital Weigh Indicator

ENCLOSURE: Stainless Steel, NEMA 4X

DIMENSIONS: 9” W x 6.25” H x 4” D

LOAD CELL A/D CONVERTER: 24 bit delta sigma,

16 mv signal input

EXCITATION: 5 VDC, 120 mA max.

SENSITIVITY: 0.1 uV/grad

UPDATE RATE: 30 update/second

DISPLAY: Six digits, 0.6 inch LED, lb, kg, Set 1, Set 2,

Gross, Net, Zero, Stable

KEYPAD: Full numeric, plus function controls

POWER INPUT: 117/217 VAC, 50-60 HZ, 20 watts,

fuse 0.25A

SERIAL PORT: RS-232, full duplex (standard)

TBS-1616 Weighing Platform

NTEP Certified, Legal for Trade

CAPACITY: 250 lb x 0.05 lb

UNITS: Lb, kg

DIMENSIONS: 16” x 16” x 5”

PLATTEN: Stainless steel top and sides

LEVELING: Bubble & height-adjustable lockable feet

OVERLOAD PROTECTION: Four stops

Operating Guide | Custom Bench Scale

QS-1

QUICK START

CONFIRM ALL COMPONENTS &

ESTABLISH LOCATION OF USE

IMPORTANT!

Precision bench scales can be adversely affected by

ambient conditions. Take care to avoid environmental

conditions such as mechanical vibrations, blowing air,

electro-mechanical noise, magnetic forces and spikes

in the 120V AC supply source.

In the general location of use, unpack and identify all

components. Refer to the system diagram on the following

page re: identifying the components.

With the weighing platform placed in the specific

location of use, make certain that the base is level, and

that all four feet firmly contact a very sturdy, vibration-

free mounting surface. Adjust the feet as needed and

tighten down the locking nut on each foot.

CONNECT THE SYSTEM COMPONENTS

Following the steps and the diagram on the next

pages,proceed with connecting all the system

components.

WEIGH, SCAN, & PRINT

After connecting the system, refer to Quick Start page

QS-4 for scale operation.

Operating Guide | Custom Bench Scale

QS-2

QUICK START

CONNECT THE WEIGHING PLATFORM

1) Connect cable from the weighing platform/load cell to

the socket labeled “LOAD CELL” on the back of the

digital indicator; hand tighten the threaded collar.

CONNECT PERIPHERALS

2) Connect bar code scanner to the short cable labeled

“SCANNER” on the back of digital indicator; hand

tighten the securing screws.

3) Connect AC adapter labeled “SCANNER” to the

small jack on the scanner’s DB9 connector.

4) Connect cable from the digital indicator labeled

“PRINTER” to the thermal label printer; hand tighten

the securing screws.

5) Connect brick-style AC adapter labeled “PRINTER”

to the thermal label printer; firmly press the cable

plug into the socket.

6) Connect 120V AC power cord labeled “PRINTER” to

the printer AC adapter brick.

POWER ON

7) With the power strip switched off, plug the three

power cords into the strip, then switch on the power

strip.

8) Power on the printer.

Operating Guide | Custom Bench Scale

QS-3

QUICK START

CONNECTIONS DIAGRAM

Operating Guide | Custom Bench Scale

QS-4

QUICK START

INITIALIZE THE BAR CODE SCANNER

With the system set up, powered on, and the digital

weight indicator readout indicating “0.00”, press the

trigger on the bar code scanner and scan the

appropriate bar coded number.

The first scan after powering on the scale will initialize

the scanner. “Err 81” will display in the readout

momentarily. This is normal, as the bar code does not

scan-in when the scanner is initializing.

When the “Err 81” message goes away and the display

returns to “0.00”, the scanner is initialized.

WEIGH

With the digital weight indicator displaying “0.00”, place

the item to be weighed in the center of the weighing

platform.

SCAN

When the displayed weight stabilizes, position the

scanner approx. 2 inches from the bar code to be

scanned and press the scanner trigger. The scanner

will beep and “Id.SCAn” will display, confirming the

scan.

PRINTING LABELS

Press the PRINT key on the 7600 model digital weight

indicator to print out the custom configured label from

the TSP700ii thermal label printer.

Operating Guide | Custom Bench Scale

QS-5

QUICK START

Duplicate labels can printed while the weighed item

remains on the platform.

NOTE: The scanned-in bar code will stay in the

indicator’s memory and will print out until another bar

code is scanned in. Powering off the digital indicator will

clear the scanned-in code memory.

TROUBLE SHOOTING THE SYSTEM

In the event that the scanner or the printer does not

operate as expected:

Bar Code Scanner

• Confirm cable & power supply connections

• Confirm scanner is operating when trigger is pressed

• Adjust distance of scanner from bar code when

scanning

Printer

• Confirm cable & power supply connections

• Check label roll

• Refer to printer manual

System-Wide

• Check all cables & cable connectors

• Check AC adapters (meter output)

• Check 120V AC power sources

TECHNICAL SUPPORT

Triner Scale provides toll-free telephone technical

support to original purchasers of our products. Tech

support can be reach Mon-Fri 8:00 AM ~ 4:30 PM.

Operating Guide | Custom Bench Scale

Keypad Keys Functions

ZERO Key -Sets the scale to zero.

UNITS –S witches the scale between the primary

weighing unit & secondary weighing unit.

PRINT -Transmits formatted print to any device

connected to the RS-232 port. Holding this push-Key for

four seconds will access the RS-232 configuration

mode.

GROSS/NET -Switches the scale display between

Gross weight and Net weight.

TARE Key -Will tare off any weight setting on the

platform and enter it into the tare memory.

KEYPAD TARE -Will display whatever tare is presently

stored in the tare memory and puts the scale into the

keypad tare entry mode.

CHECK -Pressing this Key will cause the scale to

initiate the diagnostic countdown. It may also be used

as a continue key if the scale should freeze on any of

the diagnostic numbers during countdown.

CLEAR -Used when the scale is in one of the data

entry modes. Pressing this Key once will put a decimal

point onto the display and pressing it a second time will

clear the display.

ENT -Used when the scale is in one of the data entry

modes. Key is used to enter information into the system

memory.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Triner Scale

Triner Scale

Triner Scale VersiPost VP-70 Manual de usuario

Triner Scale

Triner Scale TS-70PX Manual de instalación

Triner Scale

Triner Scale TP-10 Manual de usuario

Triner Scale

Triner Scale 1200g High Precision Scale Manual de usuario

Triner Scale

Triner Scale TS-70MC Manual de usuario

Triner Scale

Triner Scale TSM5-28-LS Manual de usuario

Triner Scale

Triner Scale TS60-1010 Manual de usuario

Triner Scale

Triner Scale 600-ESeries Manual de instrucciones

Triner Scale

Triner Scale TS-70PX Manual de usuario

Triner Scale

Triner Scale TSM Series Manual de usuario

Triner Scale

Triner Scale TS-PFS Manual de usuario

Triner Scale

Triner Scale 7600E Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario