Trinamic TMCM-1140 Manual de usuario

Getting started TMCM-1140

TRINAMIC Motion Control GmbH & Co. KG

Hamburg, Germany

www.trinamic.com

STARTING UP

1. Choose your interface.

USB: connect USB interface to PC.

Download and install the file TMCM-

1140.inf (www.trinamic.com) after

connecting the power supply.

RS485 or CAN: use the interface

connector and connect an interface

converter.

Connect the chosen interface to PC.

2. Connect the 24V DC power supply.

3. Connect motor to 4-pin connector of the

module

4. Turn power ON. The green LED starts

flashing slowly and the motor is

powered but in standstill now. If this

does not occur, turn power OFF and

check your connections and power

supply!

5. Start the TMCM-IDE program.

See next page how to configure the

connection and to use the IDE.

6. Type in the open window:

ROL 0, 500 //Rotate motor 0 with speed 500

WAIT TICKS, 0, 500

MST 0

ROR 0, 250 //Rotate motor 0 with speed 250

WAIT TICKS, 0, 500

MST 0

7. Click the Assemble icon. Thereafter click the Download icon to download the code to the module.

Click the Run icon. The program will now be executed.

8. Click the Stop icon and start TMCL™Direct Mode to issue the following commands:

ROR rotate right, motor 0, value 500 -> click Execute / The motor is rotating now.

MST motor stop, motor 0-> click Execute / The motor stops now.

FIRST STEPS ARE MADE.

Please refer to the TMCM-1140 Hardware and Firmware Manuals, too.

YOU NEED

-TMCM-1140

-Stepper motor

-Serial interface: RS485, CAN, or USB

-If you choose RS485 or CAN: interface

converter suitable to your module

-Supply voltage +24V DC (9… 28V DC)

-TMCL-IDE program and PC

-Cables for interface, motor, and power

PRECAUTIONS

-Do not mix up connections or short-circuit pins.

-Avoid bounding I/O wires with motor power

wires.

-Do not exceed the maximum power supply of

+28V DC!

-Do not connect or disconnect the motor while

powered!

-START WITH POWER SUPPLY OFF!

In/Out

Interface

USB

Motor

USB

Serial USB

interface

Converter

e.g. USB-2-485

USB

RS485

CAN

Converter

e.g. USB-2-X

CAN

Pin 6 CAN_L

Pin 5 CAN_H

Pin 1 GND

RS485

Pin 4 RS485-

Pin 3 RS485+

Pin 1 GND

Power supply

Pin 2 9… 28V DC

Pin 1 GND

Note, that the

GND pin has to

be used for

power supply

and for the

interfaces also.

Motor

Pin 1 OB2

Pin 2 OB1

Pin 3 OA2

Pin 4 OA1

Getting started TMCM-1140

TRINAMIC Motion Control GmbH & Co. KG

Hamburg, Germany

www.trinamic.com

TMCL-IDE

The TMCL-IDE is available on www.trinamic.com.

6. Click Assemble first, then Download and

Run to start the program.

Assemble

Download Run StopDissemble Continue

7. Stop all running programs by clicking

Stop and start Direct Mode by clicking the

appropriate icon.

8. The TMCM-1140 is automatically detected,

if the communication is established.

9. Issue a command by choosing Instruction,

Type, Motor, and Value and click Execute

to send it to the module.

1. Make sure the COM port you intend to

use is not blocked by another program.

2. Open TMCL-IDE by clicking TMCL.exe.

3. Choose Setup and Options and

thereafter the Connection tab.

4. Choose COM port and Type. Click OK.

5. Write a program code into the editor

window and save it with File/Save.

Note, that TMCL programs run

standalone on the module, too.

TROUBLESHOOTING

IF COMMUNICATION IS NOT ESTABLISHED

-Check if the green LED lights up. If not, check

your power supply.

-Try to start Direct Mode and check, if the

module is detected automatically.

-Check, if you are using the right COM port and

it is not blocked by another program.

-Check, if the file TMCM-1140.inf is installed

correctly.

-Check your connection settings. Default: 9600

baud, address 1.

-Check if the RS485 or CAN converter functions.

IF MOTOR DOES NOT RESPOND

-Usually the communication is not established

(see above).

-Check the motor connection.

-If you are using a TMCL program try a

movement command in Direct Mode to check

if there is a problem with it.

-Restore factory settings by using instruction

137 for cancelling all settings modified by the

user.

Otros manuales para TMCM-1140

Otros manuales de Controladores de Trinamic

Trinamic

Trinamic TMCM-342 Manual de usuario

Trinamic

Trinamic TMC428 Instrucciones de instalación y funcionamiento

Trinamic

Trinamic TMCM-310 Manual de usuario

Trinamic

Trinamic TMCM-343 Manual de usuario

Trinamic

Trinamic TMCM-1210 Manual de usuario

Trinamic

Trinamic TMCM-610 Manual de usuario

Trinamic

Trinamic IDX 4803 Manual de usuario

Trinamic

Trinamic SIXpack 2 Manual de usuario

Trinamic

Trinamic TMCL-LITE TMCM-1316 Manual de usuario

Trinamic

Trinamic TMCM-1141 Manual de usuario

Trinamic

Trinamic TMCM-6110 Manual de usuario

Trinamic

Trinamic TMCM-078 Manual de usuario

Trinamic

Trinamic TMCM-351 Manual de usuario

Trinamic

Trinamic TMCM-1260 Manual de usuario

Trinamic

Trinamic TMCM-1311 Manual de uso y cuidado

Trinamic

Trinamic TMCM-1141 Manual de usuario

Trinamic

Trinamic TMCM-110 Manual de usuario

Trinamic

Trinamic TMCM-6110 Manual de usuario

Trinamic

Trinamic TMCM-1160 Manual de usuario

Trinamic

Trinamic TMCM-170-57 Manual de usuario

Trinamic

Trinamic TMCM-3110 Manual de usuario

Trinamic

Trinamic PANdrive PD42-1-1370 Manual de usuario

Trinamic

Trinamic TMCM-1181 Manual de usuario

Trinamic

Trinamic TMCM-013-42 Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

LSIS

LSIS sv-ip5a Manual de usuario

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario