Trikdis FLEXi SP3 Manual de usuario

www.trikdis.com UAB Trikdis Draugystes g. 17, LT-51229 Kaunas, Lithuania +370 37 408 040 info@trikdis.lt

Security control panel

FLEXi SP3

User manual

(Crow keypad)

November 2020

www.trikdis.com 2 November 2020

FLEXi

SP3

user manual

Attention!

Read this user manual carefully.

A representative from the company installing the alarm system will explain which functions of the FLEXi SP3 security module

must be activated to ensure proper protection of the premises.

Trademarks and patents Other trade names used in this document may be trademarks or registered

trademarks belonging to their respective manufacturers or retailers.

Manufacturer UAB “Trikdis”,

Draugystes g. 17, LT-51229 Kaunas, Lithuania

Version This document is applicable to FLEXi SP3 security modules with firmware

version v1.00 and up.

Certification CE marking

European Union directives 2004/108/EC (EMC directive)

1999/5/EC (conformity directive)

Contact information for inquiries Contact information can be found on the website www.trikdis.c

www.trikdis.com 3 November 2020

FLEXi

SP3

user manual

Contents

1 ABOUT YOUR ALARM SYSTEM ...................................................................................................................................... 4

2 MAIN TECHNICAL SPECIFICATIONS ................................................................................................................................ 4

3 POWERING THE EQUIPMENT......................................................................................................................................... 4

4 GENERAL OPERATION OF THE ALARM SYSTEM ............................................................................................................. 4

4.1 TRANSMISSION OF ALERT MESSAGES ..................................................................................................................................... 4

4.2 ALARM SYSTEM OPERATION MODES ...................................................................................................................................... 5

4.3 CONTROL OF THE ALARM SYSTEM ......................................................................................................................................... 5

4.4 CONTROL ACCESS .............................................................................................................................................................. 5

4.5 SECURITY FUNCTIONS ......................................................................................................................................................... 5

4.6 ADDITIONAL FUNCTIONS ..................................................................................................................................................... 6

5 CONTROLLING THE ALARM............................................................................................................................................ 6

5.1 CONTROLLING THE ALARM WITH A CROW KEYPAD .................................................................................................................... 6

5.2 QUICK ARMING/DISARMING OF THE ALARM SYSTEM ................................................................................................................. 7

5.3 ARMING THE ALARM IN ARM MODE ..................................................................................................................................... 7

5.4 ARMING THE ALARM IN STAY MODE ..................................................................................................................................... 7

5.5 DISARMING THE ALARM (DISARM MODE)............................................................................................................................. 8

5.5.1 Switching off the alarm after it has been activated ................................................................................................. 8

5.6 TEMPORARY ZONE BYPASS (BYPASS FUNCTION) ....................................................................................................................... 8

5.7 VIEWING AND CLEARING ALARM ACTIVATION MEMORY ............................................................................................................. 8

5.8 SETTING TIME AND DATE ON THE CR-LCD KEYPAD ................................................................................................................... 9

5.9 RESETTING FIRE (SMOKE) SENSORS........................................................................................................................................ 9

5.10 EMERGENCY CALL BUTTONS ................................................................................................................................................. 9

5.11 TROUBLESHOOTING THE ALARM SYSTEM ................................................................................................................................ 9

5.12 PROGRAMMING USER CONTROL CODES ................................................................................................................................ 10

5.12.1 Changing the administrator code ...................................................................................................................... 10

5.12.2 Entering new and editing existing User codes ................................................................................................... 10

5.12.3 Viewing and editing the partitions that the user can control using the CR-LCD keypad ................................... 11

5.12.4 Viewing partition statuses ................................................................................................................................. 11

5.12.5 Deleting User codes ........................................................................................................................................... 11

5.12.6 Duress code........................................................................................................................................................ 11

6 CONTROL USING IBUTTON KEYS .................................................................................................................................. 11

7 CONTROL USING RFID CARDS (TAGS) .......................................................................................................................... 12

8 CONTROL USING PHONE CALLS ................................................................................................................................... 12

9 CONTROL USING SMS MESSAGES ................................................................................................................................ 13

10 CONTROL OF PGM OUTPUTS ....................................................................................................................................... 14

www.trikdis.com 4 November 2020

FLEXi

SP3

user manual

1 About your alarm system

The FLEXi SP3 control panel is part of a premise security and fire alarm system. It performs sensor signal processing and

signalizer control and has integrated GSM and WiFi modems that can transmit alert messages to the central monitoring station

and to users’ mobile phones.

Representatives of the company that installed the alarm system will explain the details on the operation, configuration and

control of Your alarm system.

2 Main technical specifications

Number of security zones 10 zones (20 zones if using ATZ), can be expanded to up to 32 zones using

expanders

Number of partitions Up to 8

Ways of alerting about danger Sound, indoor and/or outdoor sirens. Strobe lights. Transmission of messages

to central monitoring station and/or users

Alert messages are transmitted To central monitoring station via GPRS to two addresses and/or via SMS

messages

To 8 user mobile phones via SMS messages

Safety requirements Meets safety requirements of the EN 60950 standard

User codes for control Up to 40 user control codes; allowed number of different iButton keys or RFID

cards – up to 40

Resistance to environmental influences

class

Meets demands of standard EN 50131 for Class II environmental classification

Operating conditions Temperature from -10 °C to +50 °C, relative humidity 80% at +20°C, no

condensation

Main power supply 230 V 50 Hz single-phase AC power network (through a step-down power

transformer). Power consumption no higher than 40 W

Backup power supply 12 V / 7 Ah battery. Current consumption no higher than 0,5 A

3 Powering the equipment

The control panel is powered by an AC power network, or, in case it fails, by a backup battery. When an AC power network is

available, the battery is charged and kept in standby mode. The time of operation using the backup battery is limited and

depends on the amount of current used by the alarm system. A voltage of 12 V is required to power additional devices.

4 General operation of the alarm system

The security-fire alarm system consists of a signal processing board (the control panel), installed in a casing along with a step-

down power transformer and backup power supply battery, with intrusion, break-in, fire and other sensors, sound and light

signalers and control equipment connected to it.

If the alarm system is armed and any of the sensors are triggered, sound and light signalizers are turned on, and, if set, alert

messages are sent to the central monitoring station and to users. If the alarm is disarmed, it will only react to the triggering of

sensors that are set to operate continuously.

4.1 Transmission of alert messages

Alert messages can be transmitted to the CMS (central monitoring station) and/or to users. Messages are sent via the selected

connectivity channels, first to the CMS and only then to users via Protegus, SMS messages and/or phone calls.

www.trikdis.com 5 November 2020

FLEXi

SP3

user manual

4.2 Alarm system operation modes

Mode Description

OFF (DISARM) In this mode, only some of the zones are protected. The alarm will only react to events in zones

set to Fire, 24 hour, Silent 24h.

ARM In this mode, all zones are protected. The alarm will react to all possible events.

STAY In this mode, a part of the zones is protected, but movement is allowed in zones set to Interior

STAY and Instant STAY. If the alarm system is operating in this mode and a Delay zone is

violated, the alarm will activate only after the entry time has elapsed.

4.3 Control of the alarm system

The alarm system can be controlled using the following devices:

 Trikdis keypad Protegus SK232LED W;

 Paradox keypads K32+, K32LED, K636, K10LED V/H, K35, TM50, TM70;

 Crow keypads CR-16, CR-LCD;

 iButton keys;

 RFID cards;

 Electric switch, by changing the state of the zone selected by the keyswitch;

 Telephone (by phone call or by sending an SMS message with specific contents);

 Protegus app;

 Remote command from monitoring station.

4.4 Control access

Control codes are used to give different users different access levels for controlling the alarm system. The user control codes

are four digits long. When choosing and entering control codes, only numbers from 0 to 9 are used, other symbols are not

available.

Types of alarm system control codes:

 Administrator code – a six-digit combination (default code - 123456). There is only one administrator code. It cannot be

deleted, but it can be changed. The Administrator code allows to add or delete other users’ control codes. The

Administrator code cannot arm/disarm the alarm;

 User code – a four-digit combination for arming/disarming the alarm system and for temporarily bypassing security

zones. It is recommended to assign every user a personal alarm control code. The memory of the FLEXi SP3 module can

store up to 40 user codes;

 SMS password – six-digit combination for controlling the alarm system via SMS messages (default code - 123456).

4.5 Security functions

Name Description

Bypass Temporarily (for one arming of the alarm system) bypasses a security zone when changing the alarm

status. The function is used when the alarm needs to be armed, but a zone is malfunctioning and the

fault cannot be easily repaired.

Bell Squawk The module can use a short siren signal to warn about the arming and disarming of the premise alarm

system.

Chime When the alarm is disarmed, the module can warn that a zone is being violated by turning on the

keypad buzzer and/or a specially programmed PGM output.

Re-ARM Used to protect against accidental disarming of the alarm. If the alarm was disarmed via phone call, but

the Delay zone was not violated, the alarm will automatically return to its previous arm mode after the

Entry Delay time passes.

www.trikdis.com 6 November 2020

FLEXi

SP3

user manual

4.6 Additional functions

Name Description

Temperature

measurement

Up to 8 temperature sensors DS18B20, DS18S20 or one temperature and humidity sensor AM2301 can

be connected to the FLEXi SP3 module. Intervals of permitted temperatures can be set for each of

them individually. If the temperature changes beyond the set interval, an event message will be

formed and sent to users.

Remote control of

devices

Additional electronic devices can be connected to the FLEXi SP3 security module’s programmable open

collector outputs and can be controlled remotely.

5 Controlling the alarm

5.1 Controlling the alarm with a Crow keypad

Crow alarm control keypads CR-16 and CR-LCD display the states of 16 zones and 2 partitions.

Buttons for setting operation modes and entering numbers

Button Description

CONTROL Button for entering the menu. Indicator is off – the control menu is off.

Indicator is blinking – the control menu is on.

MEMORY A constantly glowing indicator shows that in memory there is new information about the alarm being

triggered, and a blinking indicator shows that the keypad is operating in MEM mode. The button is also

used for choosing the memory viewing mode.

PANIC Panic button.

ARM Button for turning on full security (ARM) mode.

STAY Button for turning on STAY mode.

www.trikdis.com 7 November 2020

FLEXi

SP3

user manual

Button Description

BYPASS A constantly glowing indicator means that there are temporarily bypassed zones, and a blinking

indicator shows the keypad is operating in BYP mode. The button is also used for selecting temporary

bypass mode.

PROGRAM Programming button. Indicator is off – programming mode is off. Indicator is blinking – programming

mode is on.

1, 2 ...9, 0 Buttons for entering numbers.

ENTER Button for confirming the specified choice.

Note: 1. To turn off programming mode or delete an incorrectly entered value, press the [ENTER] button.

2. If at least one zone is violated, it will not be possible to arm the alarm system (if the FORCE property

is not assigned to the violated zones).

5.2 Quick arming/disarming of the alarm system

Arming/disarming the alarm system using a code when the security system has STAY zones.

Security modes ARM and STAY are switched to OFF/DISARM, and OFF/DISARM is switched to ARM or STAY mode.

Changing the security mode:

1. Enter [User code].

a. If the system only has one partition, skip step 2. If the system has more than one partition, the numbers of the

partitions that the user is allowed to change the modes of will light up on the keypad.

2. Press the numbers of the chosen partitions.

3. Partitions that were in ARM, STAY modes will switch to OFF/DISARM mode.

a. If the Bell Squawk function is enabled, the siren will activate twice for short periods of time as the alarm switches

off.

4. Exit delay time will be counted down for partitions that were in OFF/DISARM mode. If a Delay zone is violated during

the countdown, ARM mode will switch on, and if a Delay zone is not violated, STAY mode will switch on.

a. The respective keypad indicator ([ARM] or [STAY]) will light up.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.3 Arming the alarm in ARM mode

To switch on ARM security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [ARM].

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

4. Confirm your selection by pressing the [ENTER] button.

5. Before the Exit Delay time runs out, leave the premises and close the door.

a. On the CR-LCD keypad, the indicator [ARM] will light up. On the CR-16 keypad, the partition indicator (A, B) will light

up.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

5.4 Arming the alarm in STAY mode

To switch on STAY security mode for an alarm system that is divided into multiple partitions:

1. Press the keypad button [STAY].

2. Enter the [User code] using the keypad.

3. Press the buttons with the numbers of the partitions you want to control.

www.trikdis.com 8 November 2020

FLEXi

SP3

user manual

4. Confirm your selection by pressing the [ENTER] button.

a. On the CR-LCD keypad, the indicator [STAY] will light up. On the CR-16 keypad, the partition indicator (A, B) will start

blinking.

b. If the Bell Squawk function is enabled, the siren will activate once for a short period of time as the alarm switches

on.

Note: STAY mode is unavailable unless at least one zone is set to Interior STAY or Instant STAY.

5.5 Disarming the alarm (DISARM mode)

When the premises are protected in ARM or STAY mode, the countdown of the Entry Delay time will begin if anyone enters

the premises. You must disarm the alarm before the time runs out.

To switch off protection mode (switch on DISARM mode):

1. Enter the [User code] using the keypad.

a. If the system has only one partition, skip steps 2 and 3.

2. Press the buttons with the numbers of the partitions you want to control.

3. Confirm your selection by pressing the [ENTER] button.

a. When the alarm is off, the partition indicator or respective keypad indicator ([ARM] or [STAY]) will switch off.

b. If the Bell Squawk function is enabled, the siren will activate twice for a short period of time as the alarm switches

off.

5.5.1 Switching off the alarm after it has been activated

To switch off the alarm:

1. Enter the [User code].

a. If the system has only one partition, skip steps 2 and 3.

2. Press the buttons with the numbers of the partitions you want to control.

3. Confirm your selection by pressing the [ENTER] button.

a. If the Bell Squawk function is enabled, the siren will activate twice for a short period of time as the alarm switches

off.

b. The [MEM] indicator will light up and violated zones will start blinking. Press [MEM] and then [ENTER] to stop the

blinking of the violated zones.

5.6 Temporary zone bypass (Bypass function)

To switch on the Bypass function:

1. Press the [BYPASS] button on the keypad.

2. Enter the [User code].

a. The BYPASS indicator will start blinking.

3. Enter the two-digit numbers of the zones that you want to bypass.

4. Confirm your selection by pressing the [ENTER] button.

5. The BYPASS indicator will start glowing.

To switch off the Bypass function, repeat the same steps as above.

5.7 Viewing and clearing alarm activation memory

When the alarm is activated, the indicator [MEM] starts glowing. To find out the reason of the alarm activation:

1. Press the [MEM] button on the keypad.

2. The glowing numbers indicate which zones caused the alarm to activate.

3. To exit this mode, press the [ENTER] button.

a. If no actions are performed with the keypad, the memory viewing mode will switch off automatically after one

minute, but the memory will not be cleared and the [MEM] indicator will continue to glow.

www.trikdis.com 9 November 2020

FLEXi

SP3

user manual

4. The memory will be cleared after the alarm is switched on and the [MEM] indicator stops glowing.

5.8 Setting time and date on the CR-LCD keypad

Keypad CR-LCD

Press the [PROG] button.

Enter the 6-digit [Installer or Administrator code].

Press the [ ] (down) button.

Press the [ENTER] button.

Enter the hours [HH] and minutes [MM].

Enter the day of the month [DD], month [MM] and year [YY].

Press the [PROG] button.

Press the [ENTER] button.

5.9 Resetting fire (smoke) sensors

After the triggering of fire (smoke) sensors, to reset the sensors you must:

1. Press and hold [Ctrl] ([CONTROL]), the keypad must beep.

2. Press [0].

3. The PGM output that the fire sensors are connected to and that is set to operate in Fire sensor reset mode will activate.

4. The fire (smoke) sensors connected to the control panel’s zone will be reset.

5.10 Emergency call buttons

The keypad can be used to send messages to the security company about required help or imminent danger. This feature is

only available if you are using the services of a security company and the security system is connected to the central monitoring

station.

Hold down the following buttons together for 3 seconds:

Keypad CR-16 LED Keypad CR-LCD Description

[1] [3] [CHIME] [CONTROL] to send a message Panic about imminent danger

[4] [6] [A] [B] to send a message Fire

[7] [9] [B] [CHIME] to send a message Medical about the need for medical assistance

5.11 Troubleshooting the alarm system

On the CR-LCD keypad, the LCD screen shows text about operational trouble.

On the CR-16 LED keypad, if there is any operational trouble, the [TROUBLE] indicator on the keypad lights up. To view

operational trouble of the alarm system:

1. Hold down the [Ctrl] button until the keypad beeps. The Ctrl indicator on the keypad will begin to blink.

2. Press [9].

3. Trouble groups will light up on the keypad.

4. If you want to view a trouble group, press the corresponding button.

5. To leave troubleshooting mode, press the [ENTER] button.

Trouble descriptions

Trouble group Description of the selected group

[1]: System [1] No AC power

www.trikdis.com 10 November 2020

FLEXi

SP3

user manual

Trouble group Description of the selected group

[2] Battery malfunction

[3] Clock not set

[4] Maximum allowed current for output AUX is exceeded

[5] Maximum allowed current for siren output is exceeded

[6] No siren

[2]: Communications

[1] Faulty main connectivity channel (all connection types)

[2] Faulty second connectivity channel (all connection types)

[3] Faulty Protegus connectivity channel (all connection types)

[4] No SIM card

[5] Incorrect SIM PIN code

[6] Unable to connect to GSM network

[7] Unable to connect to WiFi network

[8] E485 module connectivity trouble (see LED indication of the module)

[3]: Zone tamper Numbers of zones with violated tampers.

[4]: 485 bus Numbers of 485 bus expanders with malfunctions.

[5]: Missing RF sensor A wireless sensor is no longer operational (periodic check time has passed). The zone number

shows the order from a separate RF table.

[6]: RF battery low A wireless sensor has indicated that its battery is about to run out. The sensor number can be

found from a separate RF table.

5.12 Programming user control codes

5.12.1 Changing the administrator code

The administrator code can be changed in TrikdisConfig software’s menu branch System Options / Access / Access codes.

5.12.2 Entering new and editing existing User codes

CR-16 LED keypad CR-LCD keypad

Press the [PROG] button. Press the [PROG] button.

Enter the 6-digit [Installer or Administrator code]. Enter the 6-digit [Installer or Administrator code].

Enter [01]. Enter a 2-digit user number (01-40).

Enter a 2-digit user number (01-40). Press the [ENTER] button.

Enter a 4-digit [User code]. Enter a 4-digit [User code].

Repeatedly enter the 4-digit [User code]. Repeatedly enter the 4-digit [User code].

Enter the partitions that the user will be able to control. Enter the partitions that the user will be able to control.

Press the [ENTER] button to save the user code. Press the [ENTER] button to save the user code.

Press the [ENTER] button to leave programming mode. Press the [ENTER] button to leave programming mode.

Otros manuales para FLEXi SP3

Tabla de contenidos

Otros manuales de Panel de control de Trikdis

Trikdis

Trikdis FLEXi SP3 Instrucciones de montaje

Trikdis

Trikdis FLEXi SP3 Manual de usuario

Trikdis

Trikdis FLEXi SP3 Manual de usuario

Trikdis

Trikdis SP231 Instrucciones de montaje

Trikdis

Trikdis SP231 Manual de usuario

Trikdis

Trikdis CG17 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas