Trikdis FLEXi SP3 Instrucciones de montaje

www.trikdis.com UAB Trikdis Draugystės g. 17, LT-51229 Kaunas, Lithuania +370 37 408 040 info@trikdis.lt

Security control panel

“FLEXi” SP3

Installation and programming manual

July, 2020

www.trikdis.com 2 July 2020

Security control panel

„FLEXi“

SP3

Table of contents

DESCRIPTION ................................................................................................................................ 6

1.1 TECHNICAL SPECIFICATIONS ....................................................................................................................................................... 7

1.2 LIST OF COMPATIBLE MODULES................................................................................................................................................... 9

1.3 PURPOSE OF EXTERNAL TERMINALS ........................................................................................................................................... 10

1.4 LED INDICATION OF OPERATION ............................................................................................................................................... 11

POWERING THE SECURITY CONTROL PANEL ................................................................................. 11

2.1 MAIN POWER SUPPLY ............................................................................................................................................................. 11

2.2 BACKUP POWER SUPPLY .......................................................................................................................................................... 11

2.3 CONTROL PANEL KITS.............................................................................................................................................................. 12

2.3.1 Control panel „FLEXi“ SP3 ........................................................................................................................................... 12

2.3.2 Control panel „FLEXi“ SP3 KIT .................................................................................................................................... 12

2.3.3 Control panel „FLEXi“ SP3 KITi ................................................................................................................................... 12

INSTALLATION OF THE SYSTEM .................................................................................................... 12

3.1 RECOMMENDED ORDER OF INSTALLATION .................................................................................................................................. 12

3.1.1 Installing the control panel into the mounting housing .............................................................................................. 13

3.1.2 Order of connecting devices ........................................................................................................................................ 14

3.1.3 Recommendations for setting the control panel’s parameters .................................................................................. 14

3.2 CONNECTING SENSORS ........................................................................................................................................................... 15

3.3 CONNECTING SMOKE DETECTORS .............................................................................................................................................. 16

3.4 SCHEMATIC FOR CONNECTING A SIREN ....................................................................................................................................... 17

3.5 SCHEMATICS FOR CONNECTING KEYPADS AND RFID READERS (WIEGAND 26/34) .............................................................................. 17

3.6 SCHEMATICS FOR CONNECTING TM17, CZ-DALLAS READERS ......................................................................................................... 19

3.7 SCHEMATIC FOR CONNECTING A TEMPERATURE SENSOR ................................................................................................................ 20

3.8 SCHEMATICS FOR CONNECTING A RELAY AND AN LED INDICATOR .................................................................................................... 20

3.9 SCHEMATIC FOR CONNECTING ETHERNET COMMUNICATOR E485 ................................................................................................... 20

3.10 SCHEMATIC FOR CONNECTING RF-SH ........................................................................................................................................ 20

3.11 SCHEMATICS FOR CONNECTING IO SERIES EXPANDER MODULES....................................................................................................... 20

3.12 SCHEMATICS FOR CONNECTING RF TRANSMITTER T16 .................................................................................................................. 21

3.13 TURNING ON THE CONTROL PANEL ............................................................................................................................................ 21

REMOTE CONTROL ....................................................................................................................... 21

4.1 LINKING THE „FLEXI“ SP3 TO A USER’S PROTEGUS ACCOUNT ........................................................................................................ 21

4.2 ARMING/DISARMING THE SYSTEM USING PROTEGUS .................................................................................................................... 22

4.3 CONFIGURATION AND CONTROL VIA SMS MESSAGES .................................................................................................................... 22

4.4 CONTROL VIA PHONE CALL ....................................................................................................................................................... 24

SETTING PARAMETERS USING TRIKDISCONFIG SOFTWARE ........................................................... 24

5.1 DESCRIPTION OF TRIKDISCONFIG STATUS BAR.............................................................................................................................. 25

5.2 “SYSTEM OPTIONS” WINDOW .................................................................................................................................................. 26

5.3 “REPORTING TO CMS” WINDOW ............................................................................................................................................. 30

5.4 “USERS & REPORTING” WINDOW ............................................................................................................................................. 32

5.4.1 Linking RFID key fobs (cards) ...................................................................................................................................... 33

5.4.2 Linking electronic (iButton) keys ................................................................................................................................. 33

5.5 “MODULES” WINDOW ........................................................................................................................................................... 35

5.6 “WIRELESS” WINDOW ............................................................................................................................................................ 36

5.6.1 Linking the wireless equipment transceiver RF-SH to the „FLEXi“ SP3 control panel .................................................. 36

5.6.2 Linking wireless (FW2 series) sensors ......................................................................................................................... 36

5.6.3 Linking a wireless (FW2 series) remote controller ...................................................................................................... 37

www.trikdis.com 3 July 2020

Security control panel

„FLEXi“

SP3

5.6.4 Linking a wireless (FW2 series) siren ........................................................................................................................... 38

5.6.5 Linking wireless (SH series) sensors ............................................................................................................................ 38

5.6.6 Linking a wireless (SH series) keypad .......................................................................................................................... 39

5.7 “ZONES” WINDOW ................................................................................................................................................................ 40

5.8 “PGM” WINDOW ................................................................................................................................................................. 42

5.9 “SENSORS” WINDOW ............................................................................................................................................................. 45

5.10 “SYSTEM EVENTS” WINDOW .................................................................................................................................................... 46

5.11 “EVENTS LOG” WINDOW ......................................................................................................................................................... 47

5.12 RESTORE DEFAULT SETTINGS .................................................................................................................................................... 47

5.13 UPDATING FIRMWARE ............................................................................................................................................................ 47

www.trikdis.com 4 July 2020

Security control panel

„FLEXi“

SP3

Warranty and limitation of liability

The control panel is given a 24-month warranty effective from the date of sale-purchase. For the duration of the warranty

period, free repairs are guaranteed for faults caused by the manufacturer.

The warranty is valid if the control panel was installed by qualified personnel following the instructions in this document

and the applicable regulations for installing electrical equipment and operated following the instructions in this document

and the applicable regulations for safe operation of electrical equipment.

The control panel must be submitted for repairs in the manufacturer‘s packaging along with a defect report stating the

nature of the malfunction.

Once the warranty has expired, the control panel‘s technical maintenance and repairs are performed at the buyer‘s

expense.

The warranty can be terminated prematurely if:

 Unauthorized personnel repaired or tried to repair the control panel;

 The panel was used for anything other than its intended purpose;

 The panel was stored and (or) installed in unsuitable premises that had incompatible climate conditions or an aggressive

chemical environment;

 The panel was mechanically broken and (or) intentionally damaged;

 The panel was damaged by force majeure circumstances (lightning discharge etc.).

The manufacturer is not responsible for:

 the control panel‘s malfunctions if the panel is installed or used not according to its manual.

 the control panel‘s malfunctions if the cause is a malfunction or loss of GSM/GPRS/Internet connectivity or malfunctions

in the operator‘s network.

 restrictions or termination of GSM/GPRS/Internet connectivity services to the panel‘s buyer or user, and shall not

compensate the panel‘s buyer or user for any property or non-property damages suffered from this.

 restrictions or termination of electricity supply service to the panel‘s buyer or user, and shall not compensate the panel‘s

buyer or user for any property or non-property damages suffered from this.

 robbery, fire of the premises or any other losses suffered by the panel‘s buyer or user, and shall not compensate the

panel‘s buyer or user for any property or non-property damages suffered from these events.

www.trikdis.com 5 July 2020

Security control panel

„FLEXi“

SP3

Safety precautions

Read this manual carefully before using the control panel.

The „FLEXi“ SP3 control panel is an electrical device, which means it must be installed and serviced only by qualified

personnel following the instructions in this document and applicable regulations for installing electrical equipment.

Power to the panel must be switched off during installation!

The control panel must be installed in a limited access location inside the premises and maintaining a safe distance from

sensitive electronic equipment. The panel is not resistant to vibrations, other mechanical effects, humidity and aggressive

chemical environments. The control panel complies with the demands applicable to Class II environmental specification of the

EN 50131 standard.

The casings, transformers, batteries and programming equipment used must meet the safety requirements of

the EN 60950 standard.

The device is powered from a 230 V voltage 50 Hz frequency power grid through a Class II step-down

transformer that reduces the voltage to 16 – 18 V or from a 16 – 24 V DC power supply. A 12 V battery with at

least 7 Ah capacity is used as a backup power supply. The current consumption depends on the power of the

connected external devices.

A two-pole automatic safety switch must be installed in the power supply circuit for protection. The gap

between switch off contacts must be at least 3mm. The safety switch must be installed in a location known to

the specialists servicing the control panel.

To disconnect the control panel from the power network:

- from the AC network – switch off the automatic safety switch;

- from the battery – disconnect the terminals.

www.trikdis.com 6 July 2020

Security control panel

„FLEXi“

SP3

Description

The „FLEXi“ SP3 control panel is a processor part of intrusion and fire alarm system. It comes with a built-in WiFi module and

2G/4G cellular modem. The „FLEXi“ SP3 allows grouping of 32 wired and wireless zones into an 8 partition system. Users can

switch protection modes of different areas of the premises remotely and with ease (with mobile app Protegus, SMS or phone

call) or with devices that support personal identification (wired and wireless keypads, electronic keys, RFID cards, etc.). Any

triggered system event is reported to the central monitoring station (CMS) and to Protegus cloud via WiFi and (or) via cellular

network if a SIM card is inserted.

When it’s recommended to choose the „FLEXi“ SP3 control panel?

- For securing small or medium sized premises which will be monitored by a security company. The „FLEXi“ SP3 supports

both wired and wireless zones. The panel can provide remote control and system information to both end-users and

the security company.

- As a replacement for existing intrusion alarm panel. „FLEXi“ SP3 allows to set a different resistor value to the type used

with the old alarm panel. This saves a lot of time during installation, as then there is no need to change resistors in each

sensor.

- When the alarm system needs to perform more functions than just protection of the premises. For example: opening

the doors and gates, watering the lawn, lighting, heating, ventilation, cooling, controlling as well as many other

automatic start and stop functions.

Features

Reporting to the security company‘s central monitoring

station (CMS):

 Event reporting either via the built-in WiFi module or

cellular 2G/4G modem.

 Additional modules to send reports via Ethernet or

VHF/UHF radio waves with chosen priority.

 Any CMS can receive reports, as long as they have

TRIKDIS software/IP receiver or any other

manufacturer’s IP receiver supporting SIA DC-09 IP

protocol.

 Design based on two decades of experience in

transmitting reports to main and backup central

monitoring station receivers, which allows security

companies to provide the highest level of protection to

premises

 A setting for necessity to send to CMS, to mandatorily send reports to CMS first, and only then to customers.

 Possibility to send event reports to CMS of two different security companies.

 Multitude number of message transmission channels and multiple transmission priority settings.

Reporting to user:

 Via Protegus mobile app, which gives warnings about alarm system events using push and special sound notifications.

 Event reporting via SMS messages to 8 cellular numbers.

 Reporting about events using pre-recorded voice notifications (up to 8 cellular numbers).

 Remote control of selected premises’ protection mode (Arm/Disarm/Stay/Sleep).

 Remote control of connected devices (lighting system, automatic gates, ventilation, heating, watering systems, etc.).

 Remote temperature measuring.

Inputs and outputs:

 10 I/O terminals, each one can be set as an input (IN) or output (OUT). Input (IN) types: ATZ, EOL, NC, NO. Different

parameters of resistors can be used in EOL and ATZ type circuits. The number of inputs IN can be expanded to 32 by

using keypads, iO-8 and iO-WL expander modules.

 The board has 2 dedicated outputs: the bell and the LED. The bell is to control the siren, and the LED is to control

indicator lights. The number of outputs can be expanded to 16 by using iO-8 and iO-WL expander modules.

www.trikdis.com 7 July 2020

Security control panel

„FLEXi“

SP3

 Seven output operational settings. Each output can be assigned with an operational logic, a preset operation schedule

or qualities, for example, thermostat mode.

 One-wire data bus (“1-Wire”) is designated to connect temperature sensors (up to 8), a temperature and humidity

sensor (1) or a key fob (“iButton”) reader.

 The GRN-YEL data bus is designated to connect 8 keypads of the same type.

 The RS485 data bus connects iO series expander modules: RF-SH radio wave wireless sensor transceiver, E485 Ethernet

module, T16 VHF or UHF radio wave transmitter.

Control of alarm system

 4-digit long control codes (40 in total), which may be used as a coercion code as well. In such scenario, entering the user

code will disarm the alarm, yet a special report will be sent to the CMS indicating that the alarm was disarmed as a result

of coercion.

 Control using keypads: Protegus SK232LED; Paradox K636, K10H(V) K32+LED, K32LED, K35, TM50, TM70; Crow keypad

CR16, CR-LCD; CZ-Dallas electronic (“iButton”) key reader; TM17 electronic key reader, RFID reader (Wiegand 26/34).

 Remote control via Protegus mobile app, phone call or SMS.

Simple installation:

 Multiple sizes of „FLEXi“ SP3 mounting kits that include a decorative white metal housing with a built-in step-down

transformer or impulse power supply.

 Default „FLEXi“ SP3 operational settings are based on many years of experience. That allows to install the system in 7

out of 10 small and medium-sized premises without the need to change the default settings.

 The „FLEXi“ SP3 control panel allows to replace the previous panel without changing the resistors in each wired sensor.

 Settings can be saved as a file to be used later.

 Device configuration via USB cable or remotely by using TrikdisConfig software.

 Remote connection via TrikdisConfig software allows not only altering „FLEXi“ SP3 parameters but monitoring the

operation of the panel as well.

 Two access levels for parameter settings: installer and administrator.

Parameter Description

Power supply voltage[AC / DC] 16 V DC or 16-24 V, 2,5 A AC

Current consumption Up to 50 mA (stand-by),

Up to 200 mA (short-term, while sending)

Backup power source [BAT] 12 V lead – acid battery, 4 Ah/7 Ah

Battery charge current Up to 500 mA

Power voltage and current for external devices

[AUX]

12 V DC, up to 1 A

Siren output [BELL] 1 A

Output [LED] 0,1 A

PGM output 0,1 A

WiFi module Yes, built-in

WiFi frequency, protocol, encryption type 2,4 GHz, 802.11 b/g/n, WPA, WPA2, WPA mixed

WiFi network configuration type DHCP or manual

SIM card 1, NANO size

GSM/GPRS modem frequencies 850 / 900 / 1800 / 1900 MHz

4G modem frequencies „FLEXi” SP3_14E

„FLEXi” SP3_24E

B1/B3/B7/B8/B20/B28

www.trikdis.com 8 July 2020

Security control panel

„FLEXi“

SP3

Parameter Description

EMEA/Thailand

4G modem frequencies „FLEXi” SP3_24S

Latin America/Australia/New Zealand

B1/B3/B4/B5/B7/B8/B28

4G modem frequencies „FLEXi” SP3_24A

North America

B2/B4/B12

Report transmission directions - To main and backup receivers of 2 different security companies;

- To Protegus cloud, to iOS/Android Protegus mobile apps;

- To 8 mobile phones via SMS messages.

Calls 8 mobile phones. If a user answers the call, announces what

happened using voice.

Event reporting transmission channels GPRS or 4G, WiFi, LAN (with module E485), SMS, Voice call,

VHF/UHF radio waves (with transmitter T16)

Protocols for connection to CMS TCP / IP or UDP / IP, or SMS

Event encoding Contact ID codes

Report encryption TRK AES 128, SIA IP AES 128

Internal clock Yes

Buffer memory capacity 60 events

Events log memory Up to 1000 events. Oldest entries deleted automatically.

User codes 40

Duress code Two code entry methods can be chosen during programming

Dual purpose terminals [I/O] 10; IN or OUT function selected during programming. When IN is

selected, available types: NC, NO, EOL, EOL_T, ATZ, ATZ_T. When

OUT is selected, the terminal becomes open collector (OC) type

with up to 100 mA current

No. of partitions 8

No. of zones 10 (20 zones if using ATZ), (can be expanded to 32 zones using

expanders)

No. of PGM outputs 2 (can be 12 if IO terminals are set as outputs. Can be expanded to

16 outputs with expanders)

Max. number of connected keypads 8

Supported keypads Protegus SK232 LED B/W

Paradox K636

Paradox K10H(V)

Paradox K32 LED

Paradox K32+ LED

Paradox K35

Paradox TM50

Paradox TM70

Crow CR16

Crow CR-LCD

Max. number of RFID readers (Wiegand 26/34) 2

1-Wire data bus length [1 WIRE] Up to 30 m

Compatible temperature sensors Maxim®/Dallas® DS18S20, DS18B20; AM2301 series

www.trikdis.com 9 July 2020

Security control panel

„FLEXi“

SP3

Parameter Description

Max. number of temperature sensors connected to

1-Wire data bus

8 (Dallas) or 1 (if an AM2301 series sensor is used)

Compatible electronic (iButton) keys [1 WIRE] Maxim®/Dallas® DS1990A

Max. no. of electronic (iButton) keys 40

RS485 data bus length Up to 100 m

Max. no. of devices connected to RS485 data bus 8

Supported modules iO-8 – expander module;

iO – expander module;

iO-MOD – iO-WL radio wave transceiver;

iO-WL – wireless expander module;

RF-SH – radio wave receiver for wireless sensors;

E485 – module for connecting to Ethernet network;

TM17 – iButton key reader;

CZ-Dallas – iButton key reader;

T16 – VHF or UHF radio wave transmitter;

RFID reader.

Operating environment Temperature from -10 °C to +50 °C, relative humidity 80% at

+20C, no condensation.

Dimensions of the control panel 117x79x25 mm

Weight 0,1 kg

Module name Current

Keypad Protegus SK232 LED B/W Min 60 mA, max 150 mA

Keypad Paradox K636 Min 40 mA, max 70 mA

Keypad Paradox K10H(V) Min 44 mA, max 72 mA

Keypad Paradox K32 LED Min 49 mA, max 148 mA

Keypad Paradox K32+ LED Min 49 mA, max 148 mA

Keypad Paradox K35 Min 30 mA, max 70 mA

Keypad Paradox ТМ50 Мin 100 mA, max 230 mA

Keypad Paradox ТМ70 Min 200 mA, max 330 mA

Keypad Crow CR16 Min 40 mA, max 75 mA

Keypad Crow CR-LCD Min 40 mA, max 75 mA

iO-8 expander module Max 20 mA

iO expander module Max 50 mA

iO-MOD – iO-WL radio wave transceiver Min 50 mA, max 150 mA

iO-WL wireless expander module Max 200 mA

RF-SH transceiver for wireless sensors Max 100 mA

E485 Ethernet communicator Min 50 mA, max 150 mA

TM17 iButton key reader Max 50 mA

www.trikdis.com 10 July 2020

Security control panel

„FLEXi“

SP3

Module name Current

CZ-Dallas iButton key reader Max 25 mА

T16 (VHF or UHF) radio wave transmitter Min 100 mA, max 1,2 A

RFID reader (Wiegand 26/34) Max 100 mA

1. Connectivity and operation indicator lights.

2. Backup power supply terminal block.

3. Main power supply terminal block.

4. External terminal block.

5. 1-WIRE data bus terminal block.

6. SMA screw-on type connector for WiFi antenna.

7. Nano-SIM card holder.

8. SMA screw-on type connector for GSM antenna.

9. USB Mini-B connector for configuring the control

panel’s settings.

Terminal Description

Power terminal Power supply terminal (16 V AC or positive 16-24 V DC)

Power terminal Power supply terminal (16 V AC or negative 16-24 V DC)

BAT+ Backup power supply positive terminal 12 V

BAT- Backup power supply negative terminal 12 V

AUX Positive 12 V power terminal for external devices

C Common negative terminal

GRN Keypad data bus

YEL Keypad data bus

A 485 Terminal A of RS485 data bus

B 485 Terminal B of RS485 data bus

IO1 – IO9 Input/output terminals (default setting – input)

IO10 Input/output terminal (default setting – PGM output, Fire Sensor Reset)

Otros manuales para FLEXi SP3

Tabla de contenidos

Otros manuales de Panel de control de Trikdis

Trikdis

Trikdis SP231 Instrucciones de montaje

Trikdis

Trikdis CG17 Manual de usuario

Trikdis

Trikdis FLEXi SP3 Manual de usuario

Trikdis

Trikdis FLEXi SP3 Manual de usuario

Trikdis

Trikdis FLEXi SP3 Manual de usuario

Trikdis

Trikdis SP231 Manual de usuario

Manuales populares de Panel de control de otras marcas

RDZ

RDZ PC-HRX Manual de usuario

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manual técnico

Efka

Efka Variocontrol V810 Manual de usuario

Cebora

Cebora 208-10 Manual de usuario

AMX

AMX AutoPatch CP-15 Manual de usuario

Satel

Satel CA-6 KLED-S Manual de usuario

Evolution

Evolution IQ plus 800 Manual de usuario

Fagor

Fagor 8040 TCO CNC Manual de usuario

Trane

Trane ComfortLink II XL950 Control Manual de usuario

AKO

AKO PROCool AKO-17635-2 Manual de usuario

ABB

ABB 6136/30M-101 Manual de usuario

Telikou

Telikou BK-603 Belt Pack Manual de usuario

Mapei

Mapei Mapeheat Thermo Touch Manual de usuario

Bosch

Bosch D9412GV4 Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manual de usuario

Sminn

Sminn BOX L VF1L EI Manual de usuario

Balboa

Balboa TP600 Manual de usuario

Nice

Nice HSCU1 Especificaciones técnicas