TRENDnet TEW-740APBO2K Manual de usuario
Quick Installation Guide
TEW-740APBO2K
Table of Content
1 English
1. Before You Start
2. Hardware Setup and Configuration
3. Ground Wire and Pole Mount Installation
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
1
1. Before You Start
Note:
It is recommended to use network cables without additional caps, molded caps, or boots with
the access points for cable fitment inside the enclosure.
Note:
The TEW-740APBO does not support IEEE 802.3at/af PoE standards. You must use the
proprietary Power over Ethernet injector that is supplied with the TEW-740APBO. The RJ-45
Ethernet cable between the passive PoE injector and access point can have a maximum length
of up to 60 m (197 ft.).
Package Contents
Ÿ2 x TEW-740APBO
ŸCD-ROM (User's Guide)
ŸQuick Installation Guide
ŸProprietary PoE injectors
ŸPower adapters (12 V DC, 1A)
ŸMounting Hardware
ŸGrounding wires
Minimum Requirements
ŸComputer with a network port and web browser
ŸA network switch or router with an available network LAN port
ŸPhillips screwdriver (Ground wire installation)
Ÿ4 x RJ-45 network cables
2
2. Hardware Setup and Configuration
Note: By default, the TEW-740APBO access points are preconfigured to establish a point-to-
point WDS bridge between each other using a unique predefined AES encryption key. For
convenience, a unique predefined admin password has already been assigned to both access
points. You can find the preconfigured access point settings on the wireless sticker or on the
device label beneath the cover where the Ethernet ports and LEDs are located. No additional
configuration is required.
WIFI MAC: XXXXXXXXXXXXXXXXX
ETH LAN1 MAC: XXXXXXXXXXXXXXXXX
Model: TEW-740APBO / A
S/N: XXXXXXXXXXXXXXX
H/W: V2.0R FW: 2.0K
Made in XXXXXXX
IP Address: 192.168.10.50
Subnet Mask: 255.255.255.0
User Name: admin
Passwork: XXXXXXXX
Preset
Wireless Settings
Mode/WiFi Channel
WDS Bridge / CH 1
AES Encryption Key
Management Login
http://192.168.10.51
username: admin
password: XXXXXXXX
740XXXXXXXX
Unit 1 Unit 2
Preset
Wireless Settings
Mode/WiFi Channel
WDS Bridge / CH 1
AES Encryption Key
Management Login
http://192.168.10.50
username: admin
password: XXXXXXXX
740XXXXXXXX
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
3
1. Remove the cover of the access point by pushing and holding the tab in the vertical direction
upward (based on the access point orientation below) and pulling the cover in the two
locations noted below away from the access point.
Pull and hold tab
Aside from the preconfigured WDS bridge settings, the TEW-740APBO access points will also be
configured with the following default settings:
Verify connectivity between the two access points before mounting.
TEW-740APBO #1
Mode: WDS Mode
IP Address: 192.168.10.50
Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Default Gateway): 192.168.10.1
Primary DNS: 192.168.10.1
TEW-740APBO #2
Mode: WDS Mode
IP Address: 192.168.10.51
Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Default Gateway): 192.168.10.1
Primary DNS: 192.168.10.1
4
2. Remove the tab on the far left by gently bending it back and forth until the tab is removed.
This will create the opening for a RJ-45 network cable to be routed through.
Tab
3. Using a network cable, connect one end of the cable to the LAN (PoE) port and push the cable
into the cable guide on the far left, then through the opening that was created in the previous
step.
Cable Guide
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
5
4. Connect the other end of the network cable to the P+DATA OUT port on the included PoE
injector.
5. Connect the included power adapter to the PoE injector POWER IN on the included PoE
injector.
6. Plug the connected power adapter into a power outlet.
7. Confirm the device is powered on through the LED indicators.
8. Assign a static IP address to your computer's network adapter in the subnet of 192.168.10.x
(e.g. 192.168.10.10) and subnet mask of 255.255.255.0.
9. Using another network cable, connect one end to the 10/100 DATA IN port on the included
PoE injector for either the first or second access point.
10. Connect the other end of the network cable to your computer's Ethernet port.
Note: Repeat Steps 1-7 to power on and connect the second access point.
Included PoE Injector
LAN1 (PoE)
P+DATA OUT
POWER IN 10/100Mbps DATA IN
6
12. To verify connectivity on your computer, open a command prompt or terminal application
window and type in the following commands.
11. Make sure both access points are powered on approximately 15 ft. (5 m) apart from one
another with front of access points directly facing each other.
15 ft. (5m)
LAN1 (PoE)
P+DATA OUT
POWER IN
P+DATA OUT
10/100Mbps DATA IN
TEW-740APBO #1 TEW-740APBO #2
LAN1 (PoE)
POWER IN
ENGLISHFRANÇAISDEUTSCH
ESPAÑOLРORTUGUÊS
7
A successful connectivity test will appear similar to the result below for each access point. Ping
replies and 0% packet loss will indicate a successful point to point bridge connection between
the two access points.
Note: If the connectivity test fails, wait for about a minute and try again. Make sure there are no
obstacles between the two access points when running the connectivity test and make sure the
two access points are not too close together.
® ®
Note: In Windows , you can use the Command Prompt application and in Mac , you can
Terminal application to run the commands for connectivity testing.
ping 192.168.10.50
<Press Enter and wait for result>
ping 192.168.10.51
<Press Enter and wait for result>
8
3. Ground Wire and Pole Mount Installation
1. Locate the grounding point located in the bottom section of the enclosure. Using a Phillps
screwdriver, remove the grounding point screw (counter clockwise) and attach the included
grounding wire to the grounding point screw. Then reattach the ground screw (clockwise)
along with the grounding wire. After installing the grounding wire, remove another tab on the
enclosure by gently bending back and forth until the tab is removed. This will create the
opening for the ground cable to be routed through.
Note: The ground wire may need to be cut and extended using additional ground wire in order
to reach a proper grounding point.
Tab
Grounding point
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de TRENDnet
TRENDnet
TRENDnet WAP-200A Manual de usuario
TRENDnet
TRENDnet TEW-638PAP Manual de usuario
TRENDnet
TRENDnet TEW-430APB - Wireless Access Point Manual de usuario
TRENDnet
TRENDnet TEW-670AP Manual de usuario
TRENDnet
TRENDnet TEW-809UB(V1) Manual de usuario
TRENDnet
TRENDnet TEW-6APB Manual de usuario
TRENDnet
TRENDnet TEW-814DAP Manual de usuario
TRENDnet
TRENDnet TEW-825DAP Manual de usuario
TRENDnet
TRENDnet TEW-650AP Manual de usuario
TRENDnet
TRENDnet TEW-453APB - 108Mbps Wireless Super G HotSpot Access... Manual de usuario
TRENDnet
TRENDnet TEW-630APB - Wireless Access Point Manual de usuario
TRENDnet
TRENDnet TEW-750DAP Manual de usuario
TRENDnet
TRENDnet TEW-735AP Manual de usuario
TRENDnet
TRENDnet TEW-653AP Manual de usuario
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point Manual de usuario
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point Manual de usuario
TRENDnet
TRENDnet TEW-653AP Manual de usuario
TRENDnet
TRENDnet TEW-434APB - 54Mbps Wireless G PoE Access... Manual de usuario
TRENDnet
TRENDnet TEW-815DAP Manual de usuario
TRENDnet
TRENDnet TEW-230APB Manual de usuario
