TRENDnet TEW-637AP - 300Mbps Wireless Easy-N-Upgrader Manual de usuario

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

The availability of some specific channels and/or operational frequency bands are country

dependent and are firmware programmed at the factory to match the intended destination.

The firmware setting is not accessible by the end user.

European Union Notice:

Radio products with the CE marking comply with the R&TTE Directive (1999/5/EC), the EMC

Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission

of the European Community.

Compliance with these directives implies conformity to the following European Norms:

 EN 60950 Product Safety

 EN 300 328 Technical requirement for radio equipment

 EN 301 489-1/-17 General EMC requirements for radio equipment

Trademark recognition

All product names used in this manual are the properties of their respective owners and are

acknowledged.

Table of Contents

Getting Started with the TEW-637AP.................................5

Package Contents .......................................................….6

Minimum System Requirements ..................................…6

Introduction..........................................................................7

Features........................................................................…7

Hardware Overview .............................................................8

Rear Panel.....................................................................…8

Front Panel....................................................................…9

Installation Considerations ............................................…9

Getting Started ............................................................…10

Using the Configuration Menu...........................................17

Network........................................................................…18

Wireless........................................................................…20

Administrator.................................................................…31

Glossary................................................................................35

Package Contents

 TEW-637AP 11n (Draft) AP

 CAT-5 Ethernet Cable (the TEW-637AP’s Ethernet ports is Auto-MDIX)

 Power Adapter (12.0V, 1.0A)

 CD-ROM with Manual & Wizard

 Quick Installation Guide

Using a power supply with a different voltage than the one included with your product

will cause damage and void the warranty for this product.

Minimum System Requirements

Computers with Windows, Macintosh, or Linux-based operating systems with an installed

Ethernet adapter and CD-ROM.



 Internet Explorer Version 6.0 or Netscape Navigator Version 7.0 and Above

Introduction

The TEW-637AP is an 802.11n (draft 2.0) high-performance, wireless AP that supports high-speed

wireless networking at home, at work or in public places.

Unlike most Access Points, the TEW-637AP provides data transfers at up to 300 Mbps when used

with other 11n products. This AP is backwards compatible with 802.11b/g products. This means that

you do not need to change your entire network to maintain connectivity. You may sacrifice some of

802.11g’s speed when you mix 802.11n (draft2.0) and 802.11g devices, but you will not lose the ability

to communicate when you incorporate the 802.11n (draft 2.0) into your 802.11g network. You may

choose to slowly change your network by gradually replacing the 802.11g devices with 802.11n (draft

2.0) devices.

Features

 Supports IEEE 802.11n (draft 2.0) & 11b/g 2.4GHz wireless Local Area Network (WLAN)

application

 2.412 to 2.484GHz frequency band operation

 Compliant with IEEE 802.3 & 3u standards

 Support OFDM and CCK modulation

 Data rates of 1,2.5.5,6,9,12,18,24,36,48,54Mbps and 802.11n (draft 2.0) offering up to 300Mbps.

 Support one LAN port

 Support WEP & WPA security

 Support two external antennas

Hardware Overview

Auto MDI/MDIX 10/100Mbps LAN Ports

This port automatically senses the cable type when connecting to Router.

Reset Button

Pressing the reset button restores the AP to its original factory default settings.

DC-IN

The DC power input connector is a single jack socket to supply power to the

TEW-637AP. Please use the Power Adapter provided on the TEW-637AP

package.

Rear Panel

WLAN LED

A solid light indicates that the wireless segment is ready. This LED blinks during wireless data

transmission.

WPS LED

This LED blinks during WPS function is enabled.

LAN LED

A solid light indicates a connection to a Router on the LAN port. This LED blinks

during data transmission.

POWER LED

A solid light indicates a proper connection to the power supply.

WPS Button

Press the button to enable WPS function. Front Panel

Installation Considerations

The TEW-637AP AP lets you access your network, using a wireless connection, from virtually

anywhere within its operating range. Keep in mind, however, that the number, thickness and location

of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.

Typical ranges vary depending on the types of materials and background RF (radio frequency) noise

in your home or business. The key to maximizing wireless range is to follow these basic guidelines:

1 Keep the number of walls and ceilings between the TEW-637AP and other network devices to a

minimum - each wall or ceiling can reduce your wireless product’s range from 3-90 feet (1-30

meters.) Position your devices so that the number of walls or ceilings is minimized.

2 Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at

a 45-degree angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over

42 feet (14 meters) thick! Position devices so that the signal will travel straight through a wall or

ceiling (instead of at an angle) for better reception.

3 Building Materials can impede the wireless signal - a solid metal door or aluminum studs may

have a negative effect on range. Try to position wireless devices and computers with wireless

adapters so that the signal passes through drywall or open doorways and not other materials.

4 Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances

that generate extreme RF noise.

Getting Started

For a typical wireless setup at home, please do the following:

1 Connect one end of the provided network cable into your computer’s network port, and connect the

other end of the provided network cable into the TEW-637AP’s Ethernet port.

2 Plug the power adapter to outlay, and connect the power jack to the TEW-637AP.

3 Verify that the Power & Ethernet LEDs are lit.

4 Insert Setup Wizard CD into your CD-ROM drive.

5 The Welcome screen appears on your monitor. Click Start button.

6 Read the License Agreement and click Next to continue the installation.

7 Your computer will detect TEW-637AP and the Device List screen appears on your monitor. Click

Configure button to continue (default TEW-637AP IP Address is 192.168.10.100).

8 Enter password for the Access Point. The default password is “admin”. Click Login button to

continue.

Page 9

9 To change IP address, you can select “IP address setting” and click Next button to continue.

10. The default IP address is 192.168.10.100, you can choose to obtain network setting automatically,

or set the IP address manually. After setting, click Next to complete it.

11. To setup TEW-637AP or add/connect your wireless client to this AP, please select “Wireless

wizard” and click Next to continue.

Page 10

Otros manuales para TEW-637AP - 300Mbps Wireless Easy-N-Upgrader

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de TRENDnet

TRENDnet

TRENDnet TEW1750ACV2 Manual de usuario

TRENDnet

TRENDnet TEW-670AP Manual de usuario

TRENDnet

TRENDnet TEW-410APBplus Manual de usuario

TRENDnet

TRENDnet TEW-450APB - Wireless Super G Access Point Guía de instalación

TRENDnet

TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... Manual de instrucciones

TRENDnet

TRENDnet TEW-755AP Manual de usuario

TRENDnet

TRENDnet TEW-434APB - 54Mbps Wireless G PoE Access... Manual de usuario

TRENDnet

TRENDnet TEW-820AP Manual de usuario

TRENDnet

TRENDnet TEW-823DAP V2 Manual de usuario

TRENDnet

TRENDnet TEW-610APB Manual de instrucciones

TRENDnet

TRENDnet TEW-510APB Manual de usuario

TRENDnet

TRENDnet TEW-AP100plus Manual de usuario

TRENDnet

TRENDnet N300 TEW-739APBO Manual de usuario

TRENDnet

TRENDnet TEW-825DAP Manual de usuario

TRENDnet

TRENDnet TEW-310APB Manual de usuario

TRENDnet

TRENDnet TEW-650AP Manual de usuario

TRENDnet

TRENDnet TEW-430APB - Wireless Access Point Manual de usuario

TRENDnet

TRENDnet TEW-670AP Manual de usuario

TRENDnet

TRENDnet TEW-638APB Manual de usuario

TRENDnet

TRENDnet TEW-814DAP Manual de usuario

TRENDnet

TRENDnet TEW-638AP Manual de usuario

TRENDnet

TRENDnet TEW-653AP Manual de usuario

TRENDnet

TRENDnet TEW-841APBO Manual de usuario

TRENDnet

TRENDnet TEW -739APBO Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario