TRENDnet TEG-S4000 Manual de usuario
TEG-S4000
4-Slot Modular Switch
User’sGuide
Copyright Statement
COPYRIGHT 2003
ALL RIGHT RESERVED. First Edition. Printed in Taiwan.
All trademarks are the properties of their respective owners.
No portion of this document may be reproduced, altered, adapted or
translated without the prior written approval.
FCC Statement
This equipment has been tested and found to comply with the limits
for a class Adevice, purauant to part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference in a commercial installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with instructions, may cause harmful interference
on radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference, in which case, the user
will be requires to correct the interference at the user’s own expense.
Chapter 1 Introduction
The 4-Slot Modular Switch are multi-speed network
devices combining Ethernet, Fast Ethernet and Gigabit
Ethernet capabilities in a single compact,
rack-mountable cabinet. Combining 10Mbps Ethernet,
100Mbps Fast Ethernet and Gigabit Ethernet interfaces
in one unit allows these switches to unclog existing LANs
and provide a path to efficient, high-speed networking.
The 4-Slot Modular Switch is a combination of a 4-slot
host cabinet which accepts more than 15 different media
modules. A maximum configuration of 32 x
10/100Base-TX switched ports can be achieved using 4
X 8 port 10/100Base-TX modules. In the same way, a
maximum configuration of 32×10/100Base-TX or 8/16/32
×100Base-FX ports, or 4 x 1000Base-SX/LX/TX can be
accommodated in the host cabling. Any of the above
modules can be integrated to give up to many different
configurations.
Package Contents
Figure 1-1. Package Contents
The 4-Slot Modular Switch package contains the
following:
4-Slot Modular Switch
AC power cord
Rack mounting kit
Four Rubber feet
User manual
Device Description, Features and Capabilities
4-Slot Modular Switch Front and Rear Panels
This section describes the features on the front and rear
panels of the 4-Slot Modular Switch unit.
Figure 1-2. Front Panel
Figure 1-3. Rear Panel
All LED status indicators are located on the FRONT
panel of the switches. They provide a real-time indication
of system and operational status. The ports for
connections to other devices and networks are also on
the front panels, along with the crossover switches. The
following sections provide descriptions of the LED
indicators and ports.
LED
Indicators Explanation
Power The red power indicator is illuminated
when power is provided to the switch and
the switch is turned in the ON position.
Link/Activity
Green Link/Activity indicators are
illuminated when the switch detects a
connection to that port. The indicator
blinks when data is transmitted over the
network connected to that port.
When a port is not connected, the
indicator is off.
Full
Duplex/Col
Red Full Duplex/Col indicators are
illuminated when that port is in full duplex
mode. The indicator is off when that port is
in half duplex mode.
When a collision occurs on the network
connected to a port, that Full Duplex/Col
indicator blinks.
100Mbps
Green 100Mbps indicators are illuminated
when the port is operating in 100Mbps
mode. The indicator is off when the port is
operating in 10Mbps mode.
Power Port
The power port accepts the power plug.
Power Switch
The power switch, located on the rear panel, controls the
power supply
8 ports 10/100Base-TX Module
Figure 1-4. 8 port 10/100Base-TX Module
When installed into a 4-Slot Modular Switch, the
10/100Base-TX Module provides 8x 10/100Mbps Switch
ports which can connect the 4-Slot Modular Switch to a
10Mbps or 100Mbps hub or end station.
8 Ports 10/100Base-TX Module Features
8x 10/100Base-TX N-Way Switch ports.
Conforms to IEEE 802.3 10Base-T and IEEE 802.3u
100Base-TX and IEEE 802.3x Ethernet Standards
Store and forward switch architecture for abnormal
packet filtering
Support for half and full duplex on all ports
Back-plane up to 2.4Gbps
256K bytes Packet Buffer
Automatic address learning with 4K address entry
storage
Filtering and forwarding rate of 14,880~148,800
packets per second
2 ports 100Base-FX Fiber Module
Figure 1-6. 2 port 100Base-FX Module Front View
When installed into a 4-Slot Modular Switch, this Module
provides a 100Mbps Fast Ethernet fiber port which can
be used to:
Connect the Switch to the backbone of your network;
that is, to a basement switch, hub or router
Connect the Switch to a 100Mbps server or
end-station
An ST (or SC) connector provides the link to the
multi-mode fiber cabling and two indicators show the
status of the Module at-a glance.A DIP-switch sets the
operating mode to half duplex or full duplex (default).
Port 2
Port 1
DIP Switch Location
Full Duplex
Half Duplex
2
1
ON
OFF
Figure 1-7. Dip switch location and mode settings
The following Table 1-2. lists the ports’ operating modes
based on the DIP switch position.
PORT 1 PORT 2
SW 1 2
ON Half-Duplex Half-Duplex
OFF Full-Duplex Full-Duplex
Table 1-8. 2 ports 100Base-FX Fiber Module DIP switch
functions
2 ports 100Base-FX Fiber Module Features
Conforms to IEEE 802.3u Fast Ethernet standard
Support for SC or ST fiber connectors (optional)
Supports half and full duplex modes via DIP switches
Store-and-forward switch architecture for abnormal
packet filtering
2 switching 100Mbps Fiber Ethernet ports
Back-plane up to 2.4Gbps
5 Mbytes Packet Buffer
Automatic address learning with 12K address entry
storage
Filtering and forwarding rate of 148,800 packets per
second
100Base-FX uses 62.5/125 micron multi-mode fiber or
8/125 micron single mode fiber for single mode type
module.
4 Ports 100Base-FX Fiber Module
Figure1-8. 4 port 100Base-FX Front View
When installed into a 4-Slot Modular Switch, this Module
provides 4 x 100Mbps Fast Ethernet fiber ports which
can be used to:
Connect the Switch to the backbone of your network;
that is, to a basement switch, hub or router.
Connector the Switch to a 100Mbps server or end
station.
An ST (or SC) connector provides the link to the
multi-mode fiber cabling and three LEDs show five status
of the Module at-a glance. A DIP-switch sets the
operating mode to half duplex or full duplex (default).
Port 1
Port 3
Port 4
Port 2
DIP Switch Location
Full Duplex
Half Duplex
43
2
1
ON
OFF
Figure 1-9. Location and setting duplex mode
The following Table1-3. lists the ports operating modes
based on the DIP switch position.
PORT 1 PORT 2 PORT3 PORT4
SW 1 2 3 4
ON Half-Duplex Half-Duplex Half-Duplex Half-Duplex
OFF Full-Duplex Full-Duplex Full-Duplex Full-Duplex
Table 1-3. 4 ports 100Base-FX Fiber Module DIP switch
functions
4 ports 100Base-FX Fiber Module Feature
Conforms to IEEE 802.3u Fast Ethernet standard
Support SC or ST fiber connector (optional)
Support half and full duplex via DIP switches
Store-and-forward switch architecture for abnormal
packets filtering
Back-plane up to 2.4Gbps
5 M bytes Packet Buffer
Automatic address learning with 12K address entry
storage
Filtering and forwarding rate 148,800 packets per
second for 100Mbps
100Base-FX uses 62.5/125um multi-mode fiber or
8/125 um single mode fiber for single mode type
Otros manuales para TEG-S4000
1
Tabla de contenidos
Otros manuales de Cambiar de TRENDnet
TRENDnet
TRENDnet TEG-S224TX Manual de usuario
TRENDnet
TRENDnet TPE-1020WS Manual de usuario
TRENDnet
TRENDnet TPE-224WS - Web Smart PoE Switch Manual de usuario
TRENDnet
TRENDnet TE100-DX16 Manual de usuario
TRENDnet
TRENDnet TEG-2248WS - Gigabit Web Smart Switch Manual de usuario
TRENDnet
TRENDnet 1602R - KVM Switch - PS/2 Manual de usuario
TRENDnet
TRENDnet TPE-S44 - Switch Manual de usuario
TRENDnet
TRENDnet TPE-TG80G Manual de usuario
TRENDnet
TRENDnet TK-205K - PS/2 KVM Switch Manual de usuario
TRENDnet
TRENDnet TE100-S24D Manual de usuario
TRENDnet
TRENDnet TE100-H24R Manual de usuario
TRENDnet
TRENDnet TEG-S50G Manual de usuario
TRENDnet
TRENDnet TEG-S80g - Switch Manual de usuario
TRENDnet
TRENDnet TEG-S240TX - DATA SHEETS Manual de usuario
TRENDnet
TRENDnet TI-G102i Manual de usuario
TRENDnet
TRENDnet TPE-TG160g Manual de usuario
TRENDnet
TRENDnet TK-210K Manual de usuario
TRENDnet
TRENDnet TE100-S32plus Manual de usuario
TRENDnet
TRENDnet TPE-P521ES Manual de usuario
TRENDnet
TRENDnet TEG-S80Dg Manual de usuario
