TRENDnet TEG-S2500i Manual de usuario

TEG-S2500i

24+2G Stackable Switch

Quick Installation Guide

Unpacking

Open the shipping carton of the Switch and carefully unpack its contents, the carton

should contain the following items:

zOne 24+2G, 24 port Fast Ethernet Layer 2 Switch.

zMounting Kit: 2 mounting brackets and screws

zFour rubber feet with adhesive backing.

zOne AC power cord.

zOne RS-232 cable

zThis Quick Installation Guide and CD.

Note: for “Stacking” features, please install the optional Gigabit Module (purchased

separately).

Installation

Follow the guidelines below to install the Switch.

zDo not place any object weighted more than 3Kg (6.6 lb) on the Switch.

zConnect the power cord to the Switch and the power outlet.

zLeave at least 10 cm (4 inches) of space around the Switch for heat dissipation.

Desktop or Shelf Installation:

When installing the Switch on the desktop or shelf, please attach the rubber feet to the

Switch. Peel off the protective paper on the pads and attach them on the bottom of the

Switch (one at each corner).

Rack Installation:

The 24+2G Switch is rack-mountable and you can install the Switch on an EIA-19 inch

equipment rack. To do this, first install the mounting brackets on the Switch’s side panels

(one on each side), secure them with the included screws, and then use the screws

provided with the equipment rack to mount the Switch on the rack.

Power On the Switch:

The 24+2G Switch has a universal power supply and you can power up the Switch with 90

~ 260V AC, 50 ~ 60Hz power source. The AC power cord connector is located at the rear

of the unit and the On/Off switch is next to the connector. Connect the power cord from

the power outlet to the Switch and push the On/Off Switch to “ON” position to power on

the Switch. After the Switch is powered on, it will perform “self-diagnostic” (POSD). This

process takes about 100 seconds to complete, during this process, the “DIAG” LED will

blink green and the Switch will not response to any configuration program and all the

connections to the Switch will not be available. When the processed is completed, the

“DIAG” LED will stay solid green.

Below is a table that describes the meaning of each LED indicator.

LED indicators information

Status

LED Color Solid Blinking

Power Green Power is applied to this device N/A

DIAG Green Self diagnostic successful Performing self

diagnostic (after

Power On)

FAN1 Red Left cooling fan failed N/A

Cooling

Fans FAN2 Red Right cooling fan failed N/A

LINK/ACT

(1 ~24 port) Green 10Mbps Ethernet connection speed TX/RX activity or

Collision

Green 100Mbps Fast Ethernet connection

speed N/A

100M

(1 ~24 port) Off 10Mbps connection speed N/A

10/100/1000Mbps Copper Gigabit Port (Optional Module)

Top LED Orange 100Mbps Fast Ethernet connection

speed (with Middle LED off) N/A

Middle LED Green 10Mbps Ethernet connection.

(with Top LED off) N/A

Bottom LED Green N/A TX/RX activity or

collision

Top+Middle

LEDs Orange

+ Green 1000Mbps Gigabit connection speed N/A

Initial set up for management

There are two ways to perform the initial setup for the Switch; one is “Out-of-Band

Configuration” (connect your PC’s serial port to the Switch’s console port with the

included RS-232 serial cable and run terminal communication program) and the other is

“In-Band Configuration” (network a PC to the Switch and run web browser or telnet). The

sections below show the instructions on how to perform both operations.

Out-of-Band Terminal Mode Configuration

If you are using Microsoft Windows, boot up the computer, go to “Start”, “Programs”,

“Accessories”, “Communications”, and open the “HyperTerminal”. After that follow the

instructions below to setup a new terminal connection for the Switch. If you are using

other communication software, please select correct COM port and setup the connection

properties according to step 3 below.

1. Type in a name for the connection (e.g. SNMP Switch), select an icon for the

connection, and click “OK”.

2. Select the COM port that you are using for this connection and click “OK”.

3. Setup the COM port properties by using the information below and click “OK”.

Bits Rate per Second = 9600

Data Bits = 8

Parity = None

Stop Bit = 1

Flow Control = None

4. Connect the included serial cable from the computer’s COM port to the Switch’s

console port.

5. Power on the Switch and you will see some messages displayed on the

“HypertTerminal”. The Switch’s Power On Self Diagnostic (POSD) takes about 90

seconds. After that, you will see the login screen.

If the Switch is already powered on and finished its self-diagnostic, after running

the terminal communication program, please hit “Enter” once to get the login

screen.

6. At “username” field type in admin and hit “Enter”.

7. At “password” field type in 123 and hit “Enter”. You are now login to the Switch’s

configuration program.

8. On the lower portion of the screen, you will see descriptions of the navigation keys

(e.g. Tab, Space Bar, and Enter). Please use these keys to move around the

configuration program.

For more information about the configuration settings, please refer to the User’s Guide

in the CD-ROM.

Note: If there is no activity for 2 minutes, the console program will automatically

logout. Please reenter the password and username to login.

In-Band Configuration via Ethernet Network

In addition to terminal mode configuration, 24+2G Switch also supports In-Band

Configuration using Web Browser. Compare with terminal mode configuration, web

browser configuration is easier. You can simply connect the network-ready PC to the

Switch, open the web browser, go to the Switch’s configuration page (Switch’s IP address),

and configure the Switch by clicking on the subject on the menu.

Before you can access the switch through in-band, you must make sure the computer

connecting to the Switch has a web browser and the TCP/IP protocol (with valid IP

address) is bound to the network adapter. After that, you can either change your

computer’s IP address to the same class as the Switch’s IP address, or you can login the

Switch with the “out-of-band” method described in the previous section and configure the

Switch’s IP address to the same class as your computer’s IP address.

Below, is the Switch’s default IP information:

IP Address: 192.168.223.100

Subnet Mask: 255.255.255.0

Gateway: 192.168.223.254

Modify Switch’s IP address via Out-of-Band method

1. Login the console (note: default User Name: admin, Password: 123).

2. Use “Tab” key to select (highlight) “Switch Static Configuration” and hit “Enter”.

3. Use “Tab” key to select “Administration Configuration” and hit “Enter”.

4. Use “Tab” key to select “IP Configuration” and hit “Enter”.

5. Use “Tab” key to select “Edit” and hit “Enter”.

6. Use “Tab” key to highlight “IP Address”, enter the desired IP address (e.g.

192.168.1.100), and hit “Enter”.

7. The “Subnet Mask” is now highlighted, enter the correct subnet mask, and hit

“Enter.

8. Input the Gateway address and hit “Enter”.

9. Press and hold “Ctrl” and then hit “A” to go to the “Action Menu”.

10. Use “Tab” key to select “Save” and hit “Enter”.

11. The screen will prompt you to “restart the system…”, turn off the Switch, wait for

10 seconds, and then turn the Switch’s power back on.

After the Switch finishes the self-diagnostic, open your computer’s web browser and at the

“Address:” field, enter the Switch’s IP address (e.g. http://192.168.1.100), hit “Enter” or

click on “Go”, and the Switch’s configuration page will prompt you to enter “User Name”

and Password” to login.

(Note: default User Name: admin, Password: 123).

Modify NetworkAdapter’s IPaddress

You can change the network adapter’s IP address in the Network Adapter’s “Properties”.

We suggest that you change the network adapter’s IP to the following settings:

IPAddress: 192.168.223.101

Subnet Mask: 255.255.255.0

(Note: you don’t need to enter Gateway address at this moment.)

Reboot the computer if necessary. After the computer boots back up, open the web

browser and at the “Address” field, enter http://192.168.223.100 , hit “Enter” or click on

“Go”, and the Switch’s configuration page will prompt you to enter “User Name” and

Password” to login.

(Note: default User Name: admin, Password: 123).

For the complete configuration guide, please refer to the User’s Guide in the CD-ROM.

Technical Support

TRENDware provides free technical support for customers worldwide for the duration

of the product’s warranty period.

Technical Support via Telephone: +1-310-891-1100

Fax: +1-310-891-1111

Technical Support via Internet: http://www.trendnet.com

E-mail: [email protected]

Technical Support Hours:

7:00AM ~ 6:00PM, Monday ~ Friday, Pacific Standard Time (except holidays)

(Note: Technical Support hours and phone number are subject to change without further notice. Please check our

website www.trendnet.com for any updated information)

Tabla de contenidos

Otros manuales de Cambiar de TRENDnet

TRENDnet

TRENDnet TE100-H8E Manual de usuario

TRENDnet

TRENDnet NWay Manual de usuario

TRENDnet

TRENDnet TEG-424WS Manual de usuario

TRENDnet

TRENDnet TU-400E Manual de usuario

TRENDnet

TRENDnet TU2-400E Manual de usuario

TRENDnet

TRENDnet TEG-S8g Manual de usuario

TRENDnet

TRENDnet TEG-S4000i Manual de usuario

TRENDnet

TRENDnet TEG-S224 - DATA SHEETS Manual de usuario

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch Manual de usuario

TRENDnet

TRENDnet TK-423K - USB/PS/2 KVM Switch Manual de usuario

TRENDnet

TRENDnet TEG-S081Fi Manual de usuario

TRENDnet

TRENDnet TU2-NU4 Manual de usuario

TRENDnet

TRENDnet TK-1602R Manual de usuario

TRENDnet

TRENDnet TE100-S2424 Manual de usuario

TRENDnet

TRENDnet TK-205K - PS/2 KVM Switch Manual de usuario

TRENDnet

TRENDnet TK-209K Manual de usuario

TRENDnet

TRENDnet TI-G102i Manual de usuario

TRENDnet

TRENDnet TPE-082WS Manual de usuario

TRENDnet

TRENDnet TE100-S24D Manual de usuario

TRENDnet

TRENDnet TPE-1620WS Manual de usuario

TRENDnet

TRENDnet TEG-S28TX Manual de usuario

TRENDnet

TRENDnet TK-408K Manual de usuario

TRENDnet

TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manual de usuario

TRENDnet

TRENDnet TU2-400 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario