TRENDnet TE100-DX16 Manual de usuario
TE100-DX8
TE100-DX16
Ethernet/Fast Ethernet
Dual-Speed Stackable Hub
User’s Guide
TRENDware International, Inc.
Rev. 01 (May 1998)
6ETHFE16..01
Printed In Taiwan
RECYCLABLE
i
i
FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this user’s guide, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in
which case the user will be required to correct the interference at
his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
VCCI A Warning
ii
i
iv
TABLE OF CONTENTS
0ABOUT THIS GUIDE.......................................................... VI
Conventions ...................................................................................vi
Overview of the User’s Guide........................................................vi
1INTRODUCTION .................................................................1
Product Description .......................................................................1
Product Features ............................................................................2
Dual-Speed Ethernet Hub Technology Overview .........................4
100BASE-TX Technology Overview ..............................................5
Introduction to 100-Mbps Fast Ethernet.............................................. 5
Cables and Connectors ..........................................................................6
Topology .................................................................................................6
Network Diameter .................................................................................7
Hub Types .............................................................................................. 7
2UNPACKING AND SETUP....................................................9
Unpacking ......................................................................................9
Identifying External Components ...............................................10
Front Panel .......................................................................................... 10
Rear Panel............................................................................................ 12
Installing the Hub........................................................................13
Installation........................................................................................... 13
Rack Mounting..................................................................................... 13
Connecting the Power Supply......................................................14
Dual-Speed Stackable Hub User’s Guide
v
3UNDERSTANDING INDICATORS .........................................15
Hub State Indicators....................................................................16
SW Enable Indicator....................................................................16
Port Speed Indicators...................................................................17
Port Status Indicators..................................................................17
4MAKING CONNECTIONS...................................................19
Creating a Stack...........................................................................19
Connectivity Rules........................................................................20
Hub-to-end-node Connections......................................................21
Uplink Connection .......................................................................23
5CABLES AND CONNECTORS.............................................27
100BASE-TX Fast Ethernet Cables and Connectors .................27
Crossover Cables ..........................................................................28
6SPECIFICATIONS.............................................................31
General..........................................................................................31
Daisy-chain Specifications ..........................................................32
LED Indicators.............................................................................32
Environmental and Physical.......................................................32
About this Guide
v
i
0 ABOUT THIS GUIDE
This guide discusses how to install and use your Ethernet/Fast
Ethernet dual-speed stackable hub.
Conventions
As used in this guide, the term hub, unless otherwise noted, refers
to the eight- or sixteen-port Ethernet/Fast Ethernet dual-speed
stackable hub with which this guide was packaged, or to another
hub in the same product family.
Overview of the User’s Guide
♦ Chapter 1, Introduction. Provides information on Fast
Ethernet networks and introduces your hub’s features.
♦ Chapter 2, Unpacking and Setup. Helps you get started in
setting up the hub.
♦ Chapter 3, Understanding Indicators. Describes all LED
indicators on the hub’s front panel. Understanding these
indicators is essential to effectively using the hub.
♦ Chapter 4, Making Connections. Provides information on
connecting to the hub’s twisted-pair ports, stacking hubs,
and uplinking hubs together.
Dual-Speed Stackable Hub User’s Guide
About this Guide vi
i
♦ Appendix A, Cables and Connectors. Provides specifications
on the cables and connectors used with the hub.
♦ Appendix B, Specifications. Lists the hub’s specifications.
Dual-Speed Stackable Hub User’s Guide
Introduction 1
1
1 INTRODUCTION
This chapter introduces your hub and gives some background
information about the technology the hub uses.
Product Description
Your Ethernet/Fast Ethernet dual-speed stackable hub is designed
to allow easy integration and migration between 10-Mbps
Ethernet and 100-Mbps Fast Ethernet.
The hub can operate with both IEEE 802.3 10BASE-T connections
(twisted-pair Ethernet operating at 10 megabits per second) and
IEEE 802.3u 100BASE-TX connections (twisted-pair Fast
Ethernet operating at 100 megabits per second). All of the twisted-
pair ports support NWay auto-negotiation, allowing the hub to
automatically detect the speed of a network connection. This
means you can connect all of your Ethernet and Fast Ethernet
hosts to your hub (or to a stack of hubs in the same product
family) without any rewiring required when a host is upgraded
from 10 Mbps to 100 Mbps.
Hubs in this family can be purchased with or without a built-in
switching circuit to allow communication between network end
nodes operating at different speeds. If your hub has a SW Enable
indicator on its front panel, it has such a switching circuit. On a
Introduction
2
hub that does not have such a switching circuit, only end nodes
operating at the same speed (10 or 100 Mbps) can communicate
with each other (unless the hub is stacked with a hub that does
have such a switching circuit—see below).
Your hub has eight or sixteen twisted-pair ports and can be
stacked together with other hubs in the same product family to a
maximum of five hubs in a stack. A stack of five sixteen-port hubs
gives a total of eighty Ethernet or Fast Ethernet ports. (Stacking
is also referred to as daisy-chaining).
As long as a stack contains at least one hub with a built-in
switching circuit, 10-Mbps Ethernet nodes will be able to
communicate with 100-Mbps Fast Ethernet nodes and vice versa,
regardless of which hub in the stack any node is attached to. Note
that if two or more hubs in a stack have switching circuits built in,
only one hub’s switching circuit will be enabled; any other
switching circuits in the stack will automatically be disabled, and
only one hub’s SW Enable indicator will shine. This is to allow
intercommunication without the danger of a signal loop forming.
Because it conforms to the standards for both Ethernet and Class
II Fast Ethernet repeaters, your hub (or a stack of hubs in the
same product family) can also be “uplinked” together with a
similarly conformant hub or hub stack to expand the network still
further. The uplink connection will carry both 10- and 100-Mbps
network signals.
Product Features
The list below highlights your hub’s features and specifications:
♦ Compatible with the IEEE 802.3 10BASE-T Ethernet and
802.3u 100BASE-TX Fast Ethernet industry standards for
Otros manuales para TE100-DX16
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Cambiar de TRENDnet
TRENDnet
TRENDnet TEG-S8 - Gigabit Switch Manual de usuario
TRENDnet
TRENDnet TK-804R Manual de usuario
TRENDnet
TRENDnet TEG-S2400I - DATA SHEETS Manual de usuario
TRENDnet
TRENDnet TE100-S16Eg Manual de usuario
TRENDnet
TRENDnet TI-PG541i Manual de usuario
TRENDnet
TRENDnet TEG-224WSplus Manual de usuario
TRENDnet
TRENDnet TEG-S240TX - DATA SHEETS Manual de usuario
TRENDnet
TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manual de usuario
TRENDnet
TRENDnet TK-200K Manual de usuario
TRENDnet
TRENDnet TK-409K Manual de usuario
TRENDnet
TRENDnet TPE-T80 Manual de usuario
TRENDnet
TRENDnet TPE-T88G Manual de usuario
TRENDnet
TRENDnet TEG-S5 Manual de usuario
TRENDnet
TRENDnet TL2-E284 Manual de usuario
TRENDnet
TRENDnet TEG-S2500i Manual de usuario
TRENDnet
TRENDnet Web Smart Switch Series Manual de usuario
TRENDnet
TRENDnet TEG-S80TX Manual de usuario
TRENDnet
TRENDnet TE100-H5Eplus Manual de usuario
TRENDnet
TRENDnet TU2-NU4 Manual de usuario
TRENDnet
TRENDnet TK-208K Manual de usuario
