TRENDnet TPL-101U Manual de usuario
INTRODUCTION
The Encryption Management Utility for PLC products enables the user to find PLC devices on
the powerline network, measure data rate performance and ensure privacy by setting a user
defined network private password. This utility gives you the capability to set up a network
password on the local device connected to the computer where the utility is running. It gives you
as well, through the advanced option, the capability to set up a network password remotely on
other PLC devices through the power line.
It is recommended that the same PC chosen for initial execution of this utility remain the PC of
choice for subsequent network encryption updates. Network setup information is stored on the
PC and is used to facilitate follow-on network encryption sessions.
Before running this utility, make sure that a PLC device is properly installed and connected to
your computer.
RUNNING THE UTILITY
To run the utility, double click the PLC Configuration Utility icon on your desktop.
The wizard has five different dialog screens options accessible through the following tabs:
Device, Network, Security, Advanced and About. In the coming sections, we will explain the
purpose and the functionality of each of them.
NB: As a general rule that applies to dialog screens, pressing:
The OK and Cancel buttons means “exit utility ”
Device dialog screen
The Device dialog screen provides a list of your PLC devices connected to the computer where
the utility is running and average data rate performance of your powerline network.
Initially, the wizard starts the Device dialog screen.
Figure 1 Initial screen when wizard is started
A screen similar to Figure 1 appears. A progress bar indicates that the wizard is analyzing the
powerline network.
Once the analysis is done, a screen similar to Figure 2 appears.
In the text list box, it reports back all PLC device found that are locally connected to the computer
where the utility is running.
In most cases, one device only is listed.
In case you have more, click on one of them and hit Connect. Make sure that the State box
indicates that your PC is connected to the same device. Now you are ready to manage the
powerline network connected to this device, ensure its privacy and measure its data rate
performance.
Press Refresh button to refresh the search of the powerline devices connected to your
computer.
The progress bar will change into a status bar indicating the network average data rate.
Figure 2 Device Dialog screen
The color of the bar reflects the average performance of the powerline network:
Green: Excellent performance
Yellow: Fair performance
Red: Poor performance
Network dialog screen
The Network dialog screen provides detailed information about your powerline network.
The text list box shows all PLC devices found on your powerline network identified by their MAC
addresses. A second column indicates their data rate measurements in Mbps.
Press Scan Powerline Network button to refresh the listed information.
Figure 3 Network dialog screen
Important:
In case a PLC device in your home is not listed in the screen above, make sure that its network
password has not been made private previously with a different password than your current
private network password.
You can always reset a PLC network password to the universal one by running the PLC
Configuration Utility on the PC attached to this device and choose “HomePlug” as the network
password.
Security dialog screen
All PLC devices are shipped using “HomePlug” as a network password. The Security dialog
screen allows you to change this network password and set your own private password and
apply it to the PLC device connected to the computer where the utility is running.
Hit Restore Default button to restore the original network password “HomePlug” and apply it
locally.
Hit Set Local button to change the network password locally.
Figure 4 Security Dialog screen
Important: Your private network password must have between 4 and 24 characters. The
password is case sensitive. The password can include any letters of the alphabet, numbers or
punctuation marks. Remember this password as it will be needed when adding other devices to
the network later.
Advanced dialog screen
The Advanced dialog screen allows you to set up a network password remotely on other PLC
devices through the powerline.
Type your private network password into the Network Password text box.
The other devices on the network with PLC capabilities will have a different password printed on
either the box itself or in the documentation. Find the passwords for all devices you want to
manage and type them one by one into the Device Password text box and hit Add. This will add
the passwords to Remote Passwords text list box and set them to the currently defined Network
Password.
Note: The device must be present on the powerline in order for the password to be confirmed
and added to the Remote Passwords list.
Figure 5 Advanced dialog screen
The Status indicates whether each device is successfully set to the Network Password. “OK”
indicates success while “Fail” indicates a failure.
Hit Set All to apply your private network password to all devices that are listed in theRemote
Passwords text list box and to your local device connected to the computer wherethe utility is
running as well.
Select a password and Hit Remove to remove it from the list.
About dialog screen
The About dialog screen shows the software version.
Figure 6 About dialog screen
Otros manuales para TPL-101U
3
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Adaptador de TRENDnet
TRENDnet
TRENDnet TEW-624UB Manual de usuario
TRENDnet
TRENDnet TEW-429UB Manual de usuario
TRENDnet
TRENDnet TBW-101UB Manual de usuario
TRENDnet
TRENDnet TPL-407E Manual de usuario
TRENDnet
TRENDnet TE100-PCI Manual de usuario
TRENDnet
TRENDnet TEW-684UB - Manual de usuario
TRENDnet
TRENDnet TBW-101UB Manual de usuario
TRENDnet
TRENDnet TU2-ET100 Manual de usuario
TRENDnet
TRENDnet TBW-106UB Manual de usuario
TRENDnet
TRENDnet TEW-684UB - Manual de usuario
TRENDnet
TRENDnet TEW-229UB Manual de usuario
TRENDnet
TRENDnet TE-CF10 Manual de usuario
TRENDnet
TRENDnet TPL-402E Manual de usuario
TRENDnet
TRENDnet TEW-424UB Manual de usuario
TRENDnet
TRENDnet TU2-ET100 Manual de usuario
TRENDnet
TRENDnet HotFlash TEW-429UF Manual de usuario
TRENDnet
TRENDnet TEW-424UBK Manual de usuario
TRENDnet
TRENDnet TEW-424UB Manual de usuario
TRENDnet
TRENDnet TEW-424UBK Manual de usuario
TRENDnet
TRENDnet TBW-107UB Manual de usuario
