Traxon Mood Light Classic Manual de usuario
04
light
energy that stimulates the sense of sight
mood
temporary state of mind
mood-light
The next dimension of light, style and self-expression.
The dawning of a new experience.
05
OPERATION MANUAL
& WARRANTY
Sequence Modes: Chill (S1), Motion (S2), Action (S3), Sound (T)
Function Modes: Random (F1), Rainbow (F2), Fusion (F3), Pulse (F4)
SPEED
S1
M1
F1
S2
M2
F2
S3
M3
F3
T
M4
F4
OFF ON
Mood-Light Segment 01
Mood-Light Segment 02
Centre Button
Mood-Light Segment 03
Mood-Light Segment 04
Red Light
Green Light
Blue Light
Speed
Turn on/off the light
Mood Buttons
Sequence Modes
Function Modes
YOUR MOOD-LIGHT
This Operation Manual gives you some important and detailed information on how to use your Mood-Light. Read through
the Operation Manual carefully and follow all steps to get started.
Contents/Accessories:
1) Mood-Light
2) Remote Control (optional models)
3) 2 AAA Batteries (with each remote)
4) Power Supply Adaptor (optional models)
5) AC Power Cord (optional models)
6) Operation Manual (with each remote)
7) 1 x CR1616 Lithium Battery
8) Interconnecting Cable (Master/Slave)
9) 2 x Mounting Brackets, 2 x Screws, 4 x Supporters
GETTING STARTED
A) Installation
1) Install the CR1616 Lithium cell into the battery compartment located on the rear lower right-hand corner of the Mood-
Light. The ”+” sign on the battery should be facing outwards.
2) You can wall mount your Mood-Light as per Fig. 1:
- Screw and fix two ‘Mounting Brackets’ on the wall, amke sure that the dimension between two holes is exactly 340mm.
- Insert and fix two ‘supporters’ in the openings B1 and B2 on the reverse of the Mood-Light and suspend the Mood-
Light on the pre-installed Mounting Brackets into the openings T1 and T2.
06
(Fig.1)
340mm
T1 T2
B1 B2
07
3) You can stand your Mood-Light on the floor, on a table or on a shelf. Open the stand on the reverse of your Mood-Light
as per Fig. 2 and insert the top plate into the bottom plate. You can adjust the standing angle by adjusting the degree of
the stand.
4) You can suspend your Mood-Light as per Fig. 3:
- Insert four ‘Supporters’ into the openings T1, T2, B1 and B2 on the reverse of the Mood-Light.
- Use a Standard Ceiling Mounting kit.
- Ceiling Mounting should only be done by a qualified personel or technician.
Caution: Make sure that your Mood-Light is properly positioned and securely installed before use.
5) Each Mood-Light can be used optionally as a ‘Master’ or a ‘Slave’. For multiple unit installations you have to select one
‘Master’ unit with multiple ‘Slave’. Turn the switch on the rear of the ‘Master’ unit to the ‘Master’ position and place the
Interconnecting Cable into the ‘OUTPUT’ position on the reverse of your Mood-Light as per Fig. 4.
Turn the switch on the rear of the ‘Slave’ unit to the ‘Slave’ position and place the Interconnecting Cable from the ‘Master’
unit into the ‘INPUT’ position on the reverse of your next ‘Slave’ unit as per Fig. 4.
You can connect unlimited ‘Slave’ units in a row to the selected ‘Master’ unit.
Caution: To ensure simultaneous function for all Mood-Lights of your Mood-Light installation, make sure each unit has
been properly selected ‘Master’ or ‘Slave’.
(Fig.3)
(Fig.2)
6) Connect the Power Supply Adaptor to the Mood-Light.
7) Connect the AC Power Cord to the Power Supply Adaptor and to your socket.
8) Insert the 2 AAA Batteries into your Remote Control.
B) Turn Mood-Light Power On/Off
Always point the Remote Control to the selected ‘Master’ unit in your installation.
Press the ON button on your remote control to turn-on your Mood-Light. Note: The default start up condition of your Mood-
Light will be ON when power is connected for the first time.
You can now start and operate all Mood-Lights in your installation simultaneously, use the Color Mode, the Sequence Modes,
the Function Modes or the Sound Mode as described below.
Press the OFF button on your remote control to turn-off your Mood-Light.
08
(Fig.4)
09
MOOD-LIGHT FUNCTIONS
A) Color Mode
You can create and save any color combination for each or all of the four Mood-Light unit sections.
By changing the intensity of the three primary colors red, green, blue you can blend unlimited secondary colors for your Mood-
Light.
1) Create a Color Combination
All four unit section adjustment:
Press CENTRE BUTTON on your remote control to create one color for all four Mood-Light unit sections. All four Mood-
Light unit sections will blink once in acknowledgement of the command from your remote.
Single unit section adjustment:
Press any of the four Mood-Light unit sections (segment 01) or (segment 02) or (segment 03) or (segment 04)
on your remote control to chose any individual unit section for which you want to create a color. The selected Mood-
Light unit section will blink once in acknowledgement of the command from your remote.
Once you have selected to either adjust all four unit sections or just one, you can proceed to adjust the color as follows:
Press RED (+) or (-) to increase or decrease the intensity of the red color.
Press GREEN (+) or (-) to increase or decrease the intensity of the green color.
Press BLUE (+) or (-) to increase or decrease the intensity of the blue color.
See Illustration 1 (Color Chart Subtractive), page 26
See Illustration 2 (Color Chart Additive), page 26
Mix Chart: Magenta = mix Blue and Red
Yellow = mix Green and Red
Cyan = mix Green and Blue
White = evenly mix Red, Green and Blue
To return to the default Color Mode at any time, press CENTRE BUTTON on your remote control; this will reset any
previous setting you may have made. You can then proceed to adjust all sections or individual sections as described above.
2) Save a Color Combination
To save your last color combination, press one of the MEMORY (M1 - M2 - M3 - M4) buttons on your remote control
continuously until all units blink once in acknowledgement of your command. You can save up to four different color
combinations in this fashion.
Press any of the four MEMORY buttons to show the previously saved Mood.
You can change a saved color combination with a new color combination, by again pressing the requested MEMORY
button until all units blink once. These settings are saved even during removal of power.
B) Sequence Modes
You can display three pre-programmed, animated light sequences: Chill, Motion and Action.
1) Chill
Seductive, tranquil, relaxed – Chill is a light sequence to sooth your mind and calm your soul.
Press CHILL (S1) on your remote control to start the Chill Sequence.
To stop the Chill Sequence and to start another mode– press any other button.
2) Motion
Interchanging waves crashing into psychedelic colors and effects – Motion is a light sequence to stimulate your senses.
Press MOTION (S2) on your remote control to start the Motion Sequence.
To stop the Motion Sequence and to start another mode - press any other button.
3) Action
Fusion of techno and beat effects – Action is a light sequence of intense energy that will thrill your mind.
Press ACTION (S3) on your remote control to start the Action Sequence.
To stop the Action Sequence and to start another mode - press any other button.
C) Sound Mode
Color effects pulse in sync with music beats using a built in sound sensor. Play your music and adjust the volume of your
audio device to maximize the effect.
Press SOUND (T) on your remote control to start the Sound Mode.
To stop the Sound Mode and to start another mode - press any other button.
10
11
D) Function Modes
You can display four active light functions and control the speed of the functions.
1) Random
The Random Function is a display of unlimited and changing combinations of colors.
Press RANDOM (F1) on your remote control to start the Random Function.
Press SPEED (+) or (-) to increase or decrease the speed of the Random Function.
To stop the Random Function and to start another mode - press any other button.
2) Rainbow
The Rainbow Function is a display of colors in sequence of the rainbow colors.
Press RAINBOW (F2) on your remote control to start the Rainbow Function.
Press SPEED (+) or (-) to increase or decrease the speed of the Rainbow Function.
To stop the Rainbow Function and to start another mode - press any other button.
3) Fusion
The Fusion Function is a display of fading and gradually changing colors.
Press FUSION (F3) on your remote control to start the Fusion Function.
Press SPEED (+) or (-) to increase or decrease the speed of the Fusion Function.
To stop the Fusion Function and to start another mode - press any other button.
4) Pulse
The Pulse Function is a display of a pulsating light and can be displayed in four different colors and with interchanging
colors.
Press PULSE (F4) on your remote control to start the Pulse in red color.
Press PULSE (F4) again to change to green color.
Press PULSE (F4) again to change to blue color.
Press PULSE (F4) again to change to white color.
Press PULSE (F4) again to change to interchanging colors.
Press SPEED (+) or (-) to increase or decrease the speed of the Pulse Function.
To stop the Pulse Function and to start another mode - press any other button.
Tabla de contenidos
Idiomas:
Otros manuales de Luminaria de Traxon
Manuales populares de Luminaria de otras marcas
Emos
Emos CLASSIC ZY1431T Manual de usuario
Westinghouse
Westinghouse Outdoor Lighting Fixture Manual de usuario
Hedler
Hedler C 12 silent Manual de usuario
Blizzard Lighting
Blizzard Lighting Puck: CSI Manual de usuario
Energetic Lighting
Energetic Lighting ELYSL-5004 Series Manual de usuario
Lightmaxx
Lightmaxx Shaft 5R Manual de usuario
Cooper Lighting
Cooper Lighting Halo L3232E Manual de usuario
Stageline
Stageline ODW-2410RGBW Manual de usuario
Light Sky
Light Sky Tornado Series Manual de usuario
Lightolier
Lightolier Paralyte 2424 PLA2G9LS26U Manual de usuario
Lightolier
Lightolier Lytespan 83ED17S Manual de usuario
Lightolier
Lightolier Calculite CS8226 Manual de usuario