Transition Networks SGETF1013-110 Manual de usuario

*Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network installation.

Note: The chassis version of the media converter is CGETF10xx-11x. For more

information, see the CGETF10xx-1xx user’s

guide on-line at: www.transition.com.

User’s Guide

SGETF10xx-1xx

Stand-Alone Media Converter

•Gigabit Ethernet

• Copper to Fiber

• 1000Base-T to 1000Base-SX/LX

Transition Networks SGETF10xx-1xx Gigabit

Ethernet media converter connects 1000Base-T

shielded or unshielded twisted-pair copper cable to

1000Base-SX or 1000Base-LX, fiber-optic cable.

The SGETF10xx-1xx is a stand-alone media

converter

Installation . . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .7

Cable Specifications . . . . . . . . . . . . . .9

Technical Specifications . . . . . . . . . .11

Troubleshooting . . . . . . . . . . . . . . .12

Compliance Information . . . . . . . . .15

Part Number Port One - Copper Port Two - Duplex Fiber-Optic

SGETF1013-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-SX, 850 nm multimode

220 m (721 ft)* (62.5/125 µm cable)

550 m (1,804 ft)* (50/125 µm cable)

SGETF1014-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1310 nm single mode

10 km (6.2 miles)*

SGETF1015-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1310 nm single mode

25 km (15.5 miles)*

SGETF1017-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1550 nm single mode

65 km (40.4 miles)*

SGETF1024-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-SX, 1310 nm extended

multimode, 2 km (1.2 miles)*

Note: 62.5/125 µm (fiber only)

SGETF1035-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1550 nm single mode

125 km (77.5 miles)*

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Part Number Port One - Copper Port Two - Single Fiber-Optic

SGETF1029-110 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1310 TX/1550 RX

single mode, 20 km (12.4 miles)*

SGETF1029-111 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1550 TX/1310 RX

single mode, 20 km (12.4 miles)*

SGETF1029-112 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1310 TX/1550 RX

single mode, 40 km (24.8 miles)*

SGETF1029-113 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1550 TX/1310 RX

single mode, 40 km (24.8 miles)*

SGETF1029-116 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1510 TX/1590 RX

single mode, 80 km (49.7 miles)*

SGETF1029-117 RJ-45 1000Base-T

100 m (328 ft)*

SC, 1000Base-LX, 1590 TX/1510 RX

single mode, 80 km (49.7 miles)*

The SGETF1029-11x and the SGETF1029-11x are to be installed in

the same network, where one is the local converter and the other

is the remote converter.

* Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network installation (TX = transmit, RX = receive).

*Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network.

Note: Third-party Multi-Source Agreement (MSA) compliant Small Form Factor

Pluggables (SFPs) can also be used in the SGETF1040-110.

Sold separately, the following SFP transceiver modules for port two are compatible

with the SGETF1040-110 converter and are available from Transition Networks.

SGETF1040-110 Descriptions

TN-SFP-SX LC, 1000Base-SX, 850 nm multimode, 220-550 mm (720-1804 ft)*

TN-SFP-SXD LC, 1000Base-SX, 850 nm multimode, 220-550 mm (720-1804 ft)*

TN-SFP-LX1 LC, 1000Base-LX, 1310 nm single mode, 10 km (6.2 miles)*

TN-SFP-LX3 LC, 1000Base-LX, 1310 nm single mode, 30 km (18.8 miles)*

TN-SFP-LX5 LC, 1000Base-LX, 1550 nm single mode, 50 km (31.2 miles)*

TN-SFP-LX8 LC, 1000Base-LX, 1550 nm single mode, 80 km (50.0 miles)*

TN-SFP-LX12 LC, 1000Base-LX, 1550 nm single mode, 120 km (74.6miles)*

Part Number Port One - Copper Port Two - Single Fiber-Optic

SGETF1040-110 RJ-45 1000Base-T

100 m (328 ft)*

Open slot for SFP modules

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Installation

Set the 6-position switch

The 6-position switch is located on

the side of the media

converter.

• Use a small flat blade

screwdriver to set the

recessed switches.

• All switches are shown in the

default position, UP.

Note: Switch positions S2 and S3 work together to configure the media converter

for Pause conditions.

S1 Remote-Fault Detection

up Disabled

down Enable

S2 & S3 work in combination

Pause

10 sw position 2 up and 3 down: Symmetric

01 sw position 2 down and 3 up: Asymmetric

11 sw positions 2 and 3 up: Pause is OFF (default position) 00 sw positions 2

and 3 down: Symmetric and Asymmetric

S4 Transparent Link Pass-Through

up Enable Link Pass-Through

down Disable Link Pass-Through

S5 Fiber Auto-Negotiation

up Disable Fiber Auto-Negotiation for the fiber link

(default setting)

down Enable Fiber Auto-Negotiation for the fiber link

S6 Loop Back

up Disable RX/TX signal loop back (default setting)

down Enable RX/TX signal loop back

2. Pause (symmetric)

3. Pause (asymmetric)

4.Transparent Link Pass-Through

5. Auto-Negotiation

. Remote Fiber Fault Detect

6. Loop Back

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Installation -- Continued

Install Mode

During installation, set converter DIP switch 4 DOWN; leave all other switches in

the UP position (default). This disables Transparent Link Pass-Through and Auto-

Negotiation, allowing individual copper and fiber links to be established (both copper

port LEDs will turn ON with each device-to-device connection) independent of a complete

end-to-end connection.

Operation Mode

After installation is complete (all copper and fiber ports connected and linked), set all

switches to the UP position (default)).

Fiber Auto-Negotiation

Fiber Auto-Negotiation allows the fiber interface to detect and then advertise the

supported features of the remote device; this occurs only when a fiber cable is

connected to a device with a negotiating port. The process is as follows:

1. The fiber interface detects the supported features of the remote partner.

2. These abilities are passed to the twisted-pair interface and advertised.

3. Once the twisted-pair interface has a link at the highest common capability, it

passes the result to the fiber interface.

4. The fiber interfaces then start advertising these capabilities. At this point, the

link between the fiber and the negotiating port is complete.

If the SGETF10xu-1xu is connected via fiber to another SGETF10xu-1xu, both media

converters must have the Fiber Auto-Negotiation setting disabled (switch 5 UP).

Note: Transparent Link Pass-Through (switch position 4 enabled) cannot be turned

OFF (disabled) when Fiber Auto-Negotiation is ON (enabled).

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Installation -- continued

Install the fiber cable

1. Locate a 1000Base-SX/LX compliant fiber cable with male, two-stranded TX

to RX connectors installed at both ends.

2. Connect the fiber cables to the SGETF10xx-1xx media converter as

described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the other device (another media converter, hub, etc.)

as described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

TX TX

Device Device

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Installation -- Continued

Install the copper cable

1. Locate a 1000Base-T compliant copper cables with male, RJ-45 connectors

installed at both ends.

2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on

the SGETF10xx-1xx media converter.

3. Connect the RJ-45 connector at the other end of the cable to the RJ-45 port

on the other device (switch, workstation, etc.).

RJ-45 port

on the other device

(switch, work station, etc

RJ-45 port

on the media

converter

Power the media converter

The external power supply provided with this device is UL listed by the

manufacturer of the power supply.

1. Install the power adapter cord to the back of the media converter.

2. Connect the power adapter plug to AC power.

3. Verify that the media converter is powered by observing the illuminated LED

power indicator light.

Consult the user’s guide for the Transition Networks SPS1872-xx DC external

power supply for powering the media converter.

Power Connector

Converter Rear Panel

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Operation

Status LEDs

Use the status LEDs to monitor the SGETF10xx-1xx media converter operation in

the network.

PWR (Power) ON = Connected to external AC power.

LKF (Fiber link) ON = Fiber Connection

RXC (Copper receive) Flashing = Receiving data on the copper link.

ON = Copper Link connection

Duplex ON = Full

Remote-Fault Detect

Remote fiber fault detect (RFD) monitors the status of the fiber link. RFD must

only be enabled on the remote converter. If RFD is enabled in the device at each

end of the link, a link pass-through event will put the converters into an

unrecoverable state (unable to establish a link).

Pause

The pause feature can improve network performance by allowing one end of the

link to signal the other to discontinue frame transmission for a set period of time

to relieve buffer congestion.

The pause feature can be set to one of four settings:

• Disable (i.e., no pause)

• Symmetrical pause

• Asymmetric TX (transmit) pause

• Asymmetric RX (receive) pause

Enable the pause feature if it is present on ALL network devices attached to the

media converter(s); otherwise, disable the pause feature.

AutoCross (always on)

The AutoCross feature allows either straight-through (MDI) or crossover (MDI-X)

cables to be used when connecting to 10Base-T, 100Base-TX, or 1000Base-T

devices, such as hubs, transceivers, or network interface cards (NICs). AutoCross

determines the characteristics of the cable connection and automatically configures

the unit to link up to its companion device regardless of the cable configuration.

LKF PWR

RXTX

1000Base-X 1000Base-T

Duplex LEDRXC LED

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Operation - Continued

Link Pass-Through

The Link Pass-Through feature allows the media converter to monitor both the

fiber and copper RX (receive) ports for loss of signal. Refer to the illustration

below. For example, in the event of a loss of an RX signal (1), the media converter

will automatically disable the fiber TX (transmit) signal (2), thus, “passing through”

the link loss (3). The far-end device is automatically notified of the link loss (4),

which prevents the loss of valuable data unknowingly transmitted over an invalid

link.

Transparent Link Pass-Through

Transparent Link Pass-Through operates similar to Link Pass-Through with one

exception: the fiber link between the converters remains active. A signal is passed

through to the remote converter, causing it to shutdown the copper link, notifying

the end device of the link failure.

Auto-Negotiation

Auto-Negotiation enables automatic configuration to achieve the best possible

mode of operation over a link between devices. A device with this feature enabled

will broadcast its speed (10Mbs, 100Mbs, etc.) and duplex (half/full) capabilities to

another device with this feature, then negotiate the best mode of operation

between them—no user intervention required.

Fiber Auto-Negotiation

Fiber Auto-Negotiation allows the fiber interface to detect and then advertise the

support abilities of the remote device. It is supported only when the fiber is

connected to a device with a negotiating port.

Loop Back

This diagnostic feature enables the media converter to loop back the signal from

the RX port to the TX port for testing and troubleshooting purposes. Test signals

from a bit-error test unit can then be inserted into either the copper or fiber link

to test a particular segment.

This type of diagnostic test can only be performed from the local to the remote

device with loop back enabled on the remote device.

SNMP

Note: SNMP is not supported in the SGETF10xx-1xx converters.

Media

Converter A Media

Converter B

Near-End

Device Far-End

Device

original fault

on the co

er link

media converter B

disables the co

er lin

media converter A

disables the fiberTX link

media converter B

loses the fiber RX link

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Cable Specifications

The physical characteristics must meet or exceed IEEE 802.3™ specifications.

Fiber cable

Bit Error Rate: <10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

SGETF1013-110 850 nm multimode

Fiber Optic Transmitter Power: min: -10.0 dBm max: -4.0 dBm

Fiber Optic Receiver Sensitivity: min: -17.0 dBm max: 0.0 dBm

Link Budget: 7.0 dB

SGETF1014-110 1310 nm single mode

Fiber-optic Transmitter Power: min: -9.5 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -20.0 dBm max: -3.0 dBm

Link Budget: 10.5 dB

SGETF1015-110 1310 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: -0.0 dBm

Fiber-optic Receiver Sensitivity: min: -24.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SGETF1017-110 1550 nm single mode

Fiber-optic Transmitter Power: min: -3.0 dBm max: 2.0 dBm

Fiber-optic Receiver Sensitivity: min: -24.0 dBm max: -3.0 dBm

Link Budget: 21.0 dB

SGETF1024-110 1300 nm extended multimode

Fiber-optic Transmitter Power: min: -10.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -17.0 dBm max: -3.0 dBm

Link Budget: 7.0 dB

SGETF1035-110 1550 nm single mode

Fiber-optic Transmitter Power: min: 0.0 dBm max: 5.0 dBm

Fiber-optic Receiver Sensitivity: min: -27.0 dBm max: -3.0 dBm

Link Budget: 27.0 dB

SGETF1029-110 1310nm TX / 1550nm RX single mode

SGETF1029-111 1550nm TX / 1310nm RX single mode

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -21.0 dBm max: -3.0 dBm

Link Budget: 13.0 dB

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Cable Specifications -- Continued

Fiber cable - Continued

SGETF1029-112 1310nm TX / 1550nm RX single mode

SGETF1029-113 1550nm TX / 1310nm RX single mode

Fiber-optic Transmitter Power: min: -3.0 dBm max: +2.0 dBm

Fiber-optic Receiver Sensitivity: min: -23.0 dBm max: -3.0 dBm

Link Budget: 20.0 dB

SGETF1029-116 1510nm TX / 1590nm RX single mode

SGETF1029-117 1590nm TX / 1510nm RX single mode

Fiber-optic Transmitter Power: min: -2.0 dBm max: +3.0 dBm

Fiber-optic Receiver Sensitivity: min: -26.0 dBm max: -3.0 dBm

Link Budget: 24.0 dB

Copper cable (Category 5 -- minimum requirement)

• Gauge = 24 to 22 AWG; Attenuation = 22.0 dB /100m @ 100 MHz

• Straight-through OR crossover cable may be used.

• Shielded twisted-pair (STP) OR unshielded twisted-pair (UTP) may be used

• All pin pairs (1&2, 3&6, 4&5, 7&8) are active in a gigabit network.

• Use only dedicated wire pairs for the active pins; e.g., blue/white & white/blue,

orange/white & white/orange, etc.

• Do not use flat or silver satin wire.

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Technical Specifications

For Transition Networks’ Model SGETF10xx-1xx or equivalent

Standards: IEEE 802.3ab™, IEEE 802.3 2000

Data Rate / Delay: 1000 Mbs/300 nsec

Dimensions: 3.25" x 0.1" x 4.8" (82mm x 25mm x 122mm)

Weight: 3 oz. (91 g) approximately

Power Supply 12VDC @ 0.8A (minimum)

Power Consumption: 5.4W, 450mA @ 12VDC

Packet Size: 10 Kbytes (maximum)

MTBF* 382,000 hours (MIL217F2 V5.0) (MIL-HDBK-217F)

1,345,000 hours (Bellcore7 V5.0)

Operating Temp: Tmra** 0°C to 50°C (32°F to 122°F)

Storage Temp: -15°C to 65°C (5°F to 149°F)

Humidity: 10% to 90%, non condensing

Altitude: 0 to 10,000 feet

Warranty: Lifetime

*MTBF is estimated using the predictability method. This method is based on MIL-217F at 25°C

ambient temperature, typical enclosure heat rise of 10°C, and nominal operating conditions and

parameters. Installation and configuration specific MTBF estimates are available upon request.

Contact Technical Support.

**Manufacturer’s rated ambient temperature.

For the most up-to-date information on the SGETF10xx-1xx media converter, view the user’s

guide on-line at: www.transition.com.

The fiber optic transmitters on this device meet Class I Laser safety requirements per IEC-

825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.

WARNING: Visible and invisible laser radiation when open. Do not stare into the beam or view

the beam directly with optical instruments. Failure to observe this warning could result in an eye

injury or blindness.

WARNING: Use of controls, adjustments or the performance of procedures other than those

specified herein may result in hazardous radiation exposure.

IMPORTANT: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422,

RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-building (inside plant)

link segments that are not subject to lightening transients or power faults. Copper-based media

ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc.,

are NOT to be connected to inter-building (outside plant) link segments that are subject to

lightening transients or power faults.

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Troubleshooting

If the media converter fails, isolate and correct the fault by determining the answers

to the following questions and then taking the indicated action:

1. Is the PWR (power) LED illuminated?

• Is the power adapter the proper type of voltage and cycle frequency for

the AC outlet?

• Is the power adapter properly installed in the media converter and in the

outlet?

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the RXC (copper link) LED illuminated?

• Check the twisted-pair copper cables for proper connection.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the LKF (fiber link) LED illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the media converter are connected

to the RX and TX ports, respectively, on the other device.

• If the media converter is connected to another SGETF10xx-1xx using

fiber, verify the fiber Auto Negotiate is disabled (DIP-switch 5 in the UP

position).

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 4.

4. Is the RXC (copper receive) LED flashing?

• If there is activity on the 1000Base-T port, disconnect and reconnect the

twisted-pair copper cable to restart the initialization process.

• Restart the workstation to restart the initialization process.

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Technical support

Technical support is available 24-hours a day

US and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-based seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

10900 Red Circle Drive

Minnetonka, MN 55343, U.S.A.

telephone: 952-941-7600

toll free: 800-526-9267

fax: 952-941-2322

SGETF10xx-1xx

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Declaration of Conformity

Name of Mfg: Transition Networks

10900 Red Circle Drive Minnetonka MN 55343 U.S.A.

Model: SGETF10xx-1xx Series Media Converters

Part Number(s): SGETF1013-110, SGETF1014-110, SGETF1015-110,

SGETF1017-110, SGETF1018-110, SGETF1024-110,

SGETF1035-110, SGETF1040-110, SGETF1029-110,

SGETF1029-111, SGETF1029-112, SGETF1029-113,

SGETF1029-116, SGETF1029-117

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the SGETF10xx-1xx to which this declaration refers is in

conformity with the following standards:

EN 55022:1994 + A1:1995 + A1:1997; EN 55024:1998 + Al:2001 + A2:2003

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

August, 2008___

Stephen Anderson, Vice-President of Engineering Date

[email protected] -- Click the “Transition Now” link for a live Web chat. 15

Compliance Information

CE Mark

FCC regulations

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at the user's own expense.

Canadian regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set

out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

European regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses

Gerätes Rundfunkstörungen auftreten. In diesem Fäll is der Benutzer für Gegenmaßnahmen

verantwortlich.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures

spécifiques appropriées.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

In accordance with European Union Directive 2002/96/EC of the European

Parliament and of the Council of 27 January 2003, Transition Networks will accept

post usage returns of this product for proper disposal. The contact information

for this activity can be found in the 'Contact Us' portion of this document.

Printed in the U.S.A. 33334.G

Trademark notice

All trademarks and registered trademarks are the property of their respective owners.

- graphic, electronic or mechanical - without written permission from Transition Networks.

SGETF10xx-1xx

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks SGFEB10xx-12x Manual de usuario

Transition Networks

Transition Networks SISTG10-211-LRT-B Series Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-N-02 Manual de usuario

Transition Networks

Transition Networks DataBand EV Manual de usuario

Transition Networks

Transition Networks ION001-A Manual de usuario

Transition Networks

Transition Networks CSEFE1012-100 Manual de usuario

Transition Networks

Transition Networks E-TBT-FRL-05 Manual de usuario

Transition Networks

Transition Networks SISTF10xx-111-LR(T) Manual de usuario

Transition Networks

Transition Networks NANOMETER E-100BTX-SX-01 Manual de usuario

Transition Networks

Transition Networks J/FE-CF-04 SMLC Manual de usuario

Transition Networks

Transition Networks CGFEB10xx-12x Manual de usuario

Transition Networks

Transition Networks CCSF30XX-100 Manual de usuario

Transition Networks

Transition Networks CFETF10 Series Manual de usuario

Transition Networks

Transition Networks CDFTF 10 Series Manual de usuario

Transition Networks

Transition Networks CBFTF1011-100 Manual de usuario

Transition Networks

Transition Networks C/F-SM-MM-05 Manual de usuario

Transition Networks

Transition Networks ARCNET AR-CF-02 Manual de usuario

Transition Networks

Transition Networks Stand-Alone Media Converter S4TEF10xx-11x Manual de usuario

Transition Networks

Transition Networks M/E-PSW-FX-01SC Manual de usuario

Transition Networks

Transition Networks SGETF1024-105 Manual de usuario

Transition Networks

Transition Networks SPSVT2611-100 Manual de usuario

Transition Networks

Transition Networks CGETF1013-100 Manual de usuario

Transition Networks

Transition Networks CFMFF1314-280 Manual de usuario

Transition Networks

Transition Networks RS485-CF-0x Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario