Trane BAYAIR30CNVENT Instrucciones de montaje

Model:

INSTALLER'S GUIDE

ALL phases of this installation must comply with

NATIONAL, STATE AND LOCAL CODES.

IMPORTANT — This Document is customer property and is to remain with this unit. Please return to service information pack upon completion of work.

Concentric Vent Kit for

Condensing Furnaces and Boilers

DO NOT APPLY TO A NON-CONDENSING FURNACE.

NOTE: If these instructions differ from those packaged with

the furnace or boiler, follow these instructions.

DESCRIPTION AND USAGE

Kit Contents:

1—Raincap

1—4"DiameterSDR-26Pipe,23.75"Long

1—21/2"DiameterSDR-26Pipe,33.12"

1—WyeconcentricFitting

Only one vent kit per each furnace or boiler is allowed.

Ventkitisfor2,2-1/2or3in.diameterpipesystems,(See

Figures3,4,5,and6forthedifferentapplications.)Both

thecombustionairandventpipesmustattachtothevent

kit.Theventkitmustterminateoutsideofthestructureand

shouldbeinstalledverticallyasshowninFigures3and4,or

horizontalasshowninFigures5and6.

NOTE: The roof vent location is preferred since it is less

susceptible to damage, has reduced chances to intake con-

taminants, and vent vapors are less visible.

NOTE: Codes and local utility requirements governing the

installation of gas red equipment, wiring, plumbing, and

ue connections must be adhered to. In the absence of local

codes, the installation must conform with the Nation Fuel

Gas Code ANSI Z223.1 "latest edition", or CAN/ CGA B149

Installation Codes. The latest code may be obtained from the

American Gas Association Laboratories 400 N. Capitol St.

NW, Washington D.C. 20001, 1-800-699-9277 or www.aga.

com

NOTE: Read the Installer's Guide before starting the instal-

lation. Refer to the Furnace or boiler Installer's Guide for

equivalent vent lengths. The BAYAIR30CNVENT is 5 equiva-

lent feet.

INTRODUCTION

ThisInstaller'sGuidecoversinstallationoftheconcentricvent

kitonallgasfireddirectventcondensingfurnaces.

BAYAIR30CNVENT

WARNING

INSTALLATION OR REPAIRS MADE BY UNQUALIFIED

PERSONS CAN RESULT IN HAZARDS TO YOU AND OTH-

ERS. INSTALLATION MUST CONFORM WITH LOCAL CODES

OR, IN THE ABSENCE OF LOCAL CODES, WITH CODES OF

THE COUNTRY HAVING JURISDICTION. THE INFORMATION

CONTAINED IN THESE INSTRUCTIONS IS INTENDED FOR

USE BY A QUALIFIED SERVICE TECHNICIAN FAMILIAR WITH

SAFETY PROCEDURES AND EQUIPPED WITH THE PROPER

TOOLS AND TEST INSTRUMENTS. FAILURE TO CAREFUL-

LLY READ AND FOLLOW ALL INSTRUCTIONS IN THESE

INSTRUCTIONS CAN RESULT IN FURNACE OR BOILER

MALFUNCTION, PROPERTY DAMAGE, PERSONAL INJURY

AND/ OR DEATH.

RAIN CAP

4" SDR-26 PIPE

2-1/2" SDR-26 PIPE

WYE - CONCENTRIC FITTING

CONCENTRIC VENT KIT

WARNING

INSTALLING AND SERVICING HEATING EQUIPMENT CAN

BE HAZARDOUS DUE TO GAS AND ELECTRICAL COMPO-

NENTS. ONLY TRAINED PERSONNEL SHOULD INSTALL OR

SERVICE HEATING EQUIPMENT. FAILURE TO FOLLOW THIS

WARNING CAN RESULT IN PRODUCT DAMAGE, PERSONAL

INJURY AND/OR DEATH.

WARNING

THIS VENT KIT IS ONLY TO BE USED FOR VENTING CAT-

EGORY IV FURNACES AND CONDENSING BOILERS. DO

NOT USE TO VENT CATEGORY I, II OR III VENT FURNACES

OR BOILERS. FAILURE TO FOLLOW THIS WARNING COULD

RESULT IN FIRE, PERSONAL INJURY OR DEATH.

Field supplied pipe and fittings are required to complete the

installation.

Thecombustionairandventpipeandfittingsmustconformto

AmericanNationalStandardsInstitute(ANSI)andAmerican

Society for Testing and Materials (ASTM) standards D1785

(schedule-40 PVC), D2665 (PVC-DWV), D2441 (SDR-21 and

SDR-26PVC),D2661(ABS-DWV),orF628(schedule-40ABS).

PipecementandprimermustconformtoASTMstandardsD2564

(PVC)orD2235(ABS).InCanada,constructallcombustionair

andventpipesforthisunitofCSAorULCcertifiedschedule-40

PVC/ABS-DWVpipeandpipecement.

WARNING

DISCONNECT POWER SUPPLY BEFORE BEGINNING IN-

STALLATION TO PREVENT PERSONAL INJURY OR DEATH

FROM ELECTRICAL SHOCK AND EQUIPMENT DAMAGE.

①

Forusewith*UH,*DH,M95,*UY,*DY,*UX,*DX,

*UC,*DC,S-SeriesFurnaces,TGCW130A90M0A

andTGXWW130A90M0Aboilers

*maybeAorT

NOTE:

Canada requires that all Category IV heating appliances use

venting material that meets ULC S636. This kit meets the

requirements to be used in a venting system.

18-CH83D1-1A-EN

INSTALLER'S GUIDE

18-CH83D1-1A-ENPage 2

MAINTAIN 12 IN.

MINIMUM CLEARANCE

ABOVE HIGHEST

ANTICIPATED SNOW

LEVEL. MAXIMUM OF

24 IN. ABOVE ROOF.

VENT

COMBUSTION

AIR

CONCENTRIC VENT

ROOF TOP APPLICATION

CONCENTRIC VENT KIT ASSEMBLED

4.5" DIA

35.2" (typ.)

3" DIA PVC

VENT/EXHAUST

3" DIA PVC INTAKE/

COMBUSTION AIR

MAY BE

LENGTHENED TO 60" MAXIMUM

WITH FIELD REPLACEMENT PIPING.

DO NOT EXTEND MAIN BODY PIPES

WITH PIPE COUPLINGS.

MAIN BODY PIPES

21.125" (typ)

INSTALLATION - ROOF TERMINATION (SEE FIG. 3)

1. Determinebestlocationforterminationkit.

2. Cutonehole(5in.diameter)forventkit.

NOTE: Ensure termination height is above the roof surface

or anticipated snow level (1 ft. in USA or 1 1/2 ft. in Canada)

as shown in Figure 4.

NOTE: If assembly is too short to meet the height require-

ment, the two pipes supplied in the kit may be replaced by

using same diameter, eld supplied SDR-26 PVC (ASTM

D2241) pipe. Do not extend the 4" pipe (24" as shipped) to

more than 60 in. (See Figure 2).

WARNING

DO NOT OPERATE THE FURNACE OR BOILER WITHOUT

THE RAIN CAP IN PLACE AS RECIRCULATION OF COM-

BUSTION PRODUCTS MAY OCCUR. WATER MAY ALSO

COLLECT INSIDE THE LARGER COMBUSTION AIR PIPE

AND FLOW TO THE BURNER ENCLOSURE. FAILURE TO

FOLLOW THIS WARNING COULD RESULT IN PRODUCT

DAMAGE OR IMPROPER OPERATION, PERSONAL INJURY

OR DEATH

CAUTION

DO NOT USE FIELD SUPPLIED COUPLINGS TO EXTEND

MAIN BODY PIPES (4" AND 2-1/2" PIPES). AIRFLOW RE-

STRICTION WILL OCCUR AND THE FURNACE OR BOILER

PRESSURE SWITCH MAY CAUSE INTERMITTENT OPERA-

TION.

3. Partiallyassembletheventkit.Cleanthepipeendsand

 adjoiningsocketswithPVCprimer(ASTMF-656)and 

 cementusingPVCcement(ASTMD-256).

 a.CementtheWyeconcentricfittingtolargerdiameterkit

  pipe.(SeeFigure1)

 b.Cementtheraincaptosmallerdiameterkitpipe.(See

  Figure1)

NOTE: Instead of cementing the smaller pipe to the rain cap,

RTV silicon sealant may be used to permit future eld disas-

sembly for cleaning

4.InstallWyefittingandpipeassemblyfromtheinsidethrough

structure'shole.Installfieldsuppliedroofboot/flashing.

NOTE: Do not allow insulation or other materials to accumu-

late inside pipe assembly when installing through hole.

5.SecureassemblytoroofstructureasshowninFigure4using

fieldsuppliedmetalstrappingorequivalentsupportmaterial.

6. Remove ribs from rain cap.  Install the rain cap and the

small diameter pipe assembly in the Wye fitting and pipe

assembly.Ensurethatthesmalldiameterpipeiscemented

andbottomedintotheWyefitting.

WARNING

DRILL A PILOT HOLE IN THE VENT PIPE FOR THE SCREW

SIZE BEING USED. FAILURE TO DRILL ADEQUATE HOLES

MAY CAUSE CRACKING OF THE PVC COMPONENTS, AL-

LOWING FLUE GASES TO BE RECIRCULATED. FAILURE TO

FOLLOW THIS WARNING COULD RESULT IN PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

② ③

7.Cementthefurnaceorboilercombustionairandventpipes

totheconcentricventterminationassembly.SeeFigure4

forproperpipeattachment.

8.CHECKOUT:OperatethefurnaceorboilertomakesureALL

pipejointsarefastenedandsealedtopreventtheescapeof

combustionproductsintothebuilding.

NOTE: Two or more installations require a minimum separa-

tion distance of approximately one inch between vent kits.

WARNING

FAILURE TO REMOVE RIBS FROM RAIN CAP FOR VERTI-

CAL VENT KIT INSTALLATIONS MAY CAUSE ICE OR SNOW

TO FORM ON THE RAIN CAP, LEADING TO AN INOPERABLE

FURNACE. FAILURE TO FOLLOW THIS WARNING COULD

RESULT IN PROPERTY DAMAGE, PERSONAL INJURY OR

DEATH.

NOTE: Kit supplied stainless steel screw will be used to se-

cure the rain cap to the pipe.

REMOVE RIBS

FROM CAP

INSTALLER'S GUIDE

18-CH83D1-1A-EN Page 3

REMOVE RIBS

FROM CAP

COMBUSTION

AIR

ROOF BOOT

(FIELD SUPPLIED)

COMBUSTION

AIR

VENT

ELBOW

(FIELD SUPPLIED)

MAINTAIN 12 IN.

(18 IN. FOR CANADA)

MINIMUM CLEARANCE

ABOVE HIGHEST

ANTICIPATED SNOW

LEVEL. MAXIMUM OF

24 IN. ABOVE ROOF

SUPPORT

(FIELD SUPPLIED)

VENT

CONCENTRIC VENT

ROOF INSTALLATION

④

INSTALLATION -SIDE WALL VENT (SEE FIGURE 5)

1. Determinethebestlocationfortheventkit.

NOTE: Consider the following when determining the vent kit

location:

A. Vent kit positioned where the vent vapors will not damage

planting/ shrubs or air conditioning equipment or building

structure.

B. Vent kit positioned so it will not be affected by wind eddy

that may allow recirculation of combustion products, or air-

borne leaves, or light snow.

C. Vent kit positioned where it will not get damaged or be

subjected to foreign objects, such as stones, balls, etc.

D. Vent kit positioned where the vent vapors will not be ob-

jectionable.

2. Cut1hole(5in.diameter)forVentkit.

3. Partiallyassembletheventkit.Cleanthepipeendsand

 adjoiningsocketswithPVCprimer(ASTMF-656)and 

 cementusingPVCcement(ASTMD-256).

 a.CementtheWyeconcentricfittingtolargerdiameterkit

  pipe.(SeeFigure1)

 b.Cementtheraincaptosmallerdiameterkitpipe.(See

  Figure1)

4. InstallWyeconcentricfittingandpipeassemblythrough

 structure'shole.

NOTE: Kit supplied stainless steel screw will be used to

secure the rain cap to the pipe.

7.Cementfurnaceorboilercombustionairandventpipesto

concentricvent assembly. SeeFigure 6for properpipe at-

tachment.

8.CHECKOUT:OperatethefurnaceorboilertomakesureALL

pipejointshavefastenedandsealedtopreventtheescapeof

combustionproductsintothebuilding.

NOTE: Two or more installations require a minimum separa-

tion distance of approximately one inch between vent kits.

CONCENTRIC VENT

SIDE WALL

COMBUSTION

AIR VENT

12" MIN TO

OVERHANG

MAINTAIN 12 IN

MINIMUM CLEARANCE

ABOVE HIGHEST

ANTICIPATED SNOW

LEVEL OR GRADE

WHICHEVER IS GREATER

⑤

RAIN CAP

COMBUSTION AIR

STRAP

(FIELD SUPPLIED)

COMBUSTION

AIR

VENT

ELBOW

(FIELD

SUPPLIED)

VENT

1" + 1/2"

CONCENTRIC VENT

SIDE WALL INSTALLATION

⑥

NOTE: To prevent the possiblility of condenate freeze-up, do

not install vent kits one above the other.

NOTE: FLUE GAS DEGRADATION

The moisture content of the ue gas may have a detrimental

effect on some building materials. This can be avoided by

using the roof or chimney venting option. When wall venting

is used on any surface that can be affected by this mois-

ture, it is recommended that a corrosion resistance shield

(24 inches square) be used behind the Vent Terminal. This

shield can be made of wood, plastic, sheet metal, etc. Also,

silicone caulk all cracks, seams, and joints within 3 feet of

the Vent Terminal.

INSTALLER'S GUIDE

6. SecureassemblytostructureasshowninFigure6usingfield

suppliedmetalstrappingorequivalentsupportmaterial.

NOTE: Ensure termination location clearance dimensions as

shown in Figure 5. Do not locate the vent cap directly to the

wall surface. A distance of 1" ± 1/2" is required to prevent

water accumulating between the vent ns.

NOTE: If assembly needs to be extended to allow side wall

thickness requirement, the two pipes supplied in the kit may

be replaced by using same diameter, eld supplied SDR-26

PVC (D2241) pipe. Do not extend the 4" pipe (24" as shipped)

to more than 60 in. (See Figure 2). The 4" pipe may be short-

ened to 14" minimum.

NOTE: Do not allow insulation or other materials to accumu-

late inside pipe assembly when installing through hole.

WARNING

DRILL A PILOT HOLE IN THE VENT PIPE FOR THE SCREW

SIZE BEING USED. FAILURE TO DRILL ADEQUATE HOLES

MAY CAUSE CRACKING OF THE PVC COMPONENTS, AL-

LOWING FLUE GASES TO BE RECIRCULATED. FAILURE TO

FOLLOW THIS WARNING COULD RESULT IN PROPERTY

DAMAGE, PERSONAL INJURY OR DEATH.

CAUTION

DO NOT USE FIELD SUPPLIED COUPLINGS TO EXTEND

MAIN BODY PIPES (4" AND 2-1/2" PIPES). AIRFLOW RE-

STRICTION WILL OCCUR AND THE FURNACE OR BOILER

PRESSURE SWITCH MAY CAUSE INTERMITTENT OPERA-

TION.

5. Installraincap andsmalldiameter pipeassemblyin Wye

concentric fitting and large pipe assembly. Ensure small

diameterpipeisbottomedandcementedinWyeconcentric

fitting.

IMPORTANT:

TheCommonwealthofMassachusettsrequirescompliance

withregulation248CMR4.00and5.00forinstallationof

through–the–wallventedgasappliancesasfollows:

Forallsidewallhorizontallyventedgasfueledequipment

installedineverydwelling,buildingorstructureusedin

wholeorinpartforresidentialpurposes,includingthose

ownedoroperatedbytheCommonwealthandwheretheside

wallexhaustventterminationislessthanseven(7)feetabove

finishedgradeintheareaoftheventing,includingbutnot

limitedtodecksandporches,thefollowingrequirementsshall

besatisfied:

1.INSTALLATIONOFCARBONMONOXIDE

DETECTORS.Atthetimeofinstallationofthesidewall

horizontalventedgasfueledequipment,theinstalling

plumberorgasfittershallobservethatahardwiredcarbon

monoxidedetectorwithanalarmandbatteryback-upis

installedonthefloorlevelwherethegasequipmentisto

beinstalled.Inaddition,theinstallingplumberorgasfitter

shallobservethatabatteryoperatedorhardwiredcarbon

monoxidedetectorwithanalarmisinstalledoneach

additionallevelofthedwelling,buildingorstructureserved

bythesidewallhorizontalventedgasfueledequipment.It

shallbetheresponsibilityofthepropertyownertosecurethe

servicesofqualifiedlicensedprofessionalsfortheinstallation

ofhardwiredcarbonmonoxidedetectors.

a. Intheeventthatthesidewallhorizontallyvented

gasfueledequipmentisinstalledinacrawlspaceoran

attic,thehardwiredcarbonmonoxidedetectorwithalarm

andbatteryback-upmaybeinstalledonthenextadjacent

floorlevel.

b. Intheeventthattherequirementsofthissubdivision

cannotbemetatthetimeofcompletionofinstallation,the

ownershallhaveaperiodofthirty(30)daystocomplywith

theaboverequirements;provided,however,thatduringsaid

thirty(30)dayperiod,abatteryoperatedcarbonmonoxide

detectorwithanalarmshallbeinstalled.

2.APPROVEDCARBONMONOXIDEDETECTORS.Each

carbonmonoxidedetectorasrequiredinaccordancewiththe

aboveprovisionsshallcomplywithNFPA720andbeANSI/UL

2034listedandIAScertified.

3.SIGNAGE.Ametalorplasticidentificationplateshall

bepermanentlymountedtotheexteriorofthebuildingata

minimumheightofeight(8)feetabovegradedirectlyinline

withtheexhaustventterminalforthehorizontallyvented

gasfueledheatingapplianceorequipment.Thesignshall

read,inprintsizenolessthanone-half(1/2)inchinsize,

“GASVENTDIRECTLYBELOW.KEEPCLEAROFALL

OBSTRUCTIONS”.

4.INSPECTION.Thestateorlocalgasinspectorofthe

sidewallhorizontallyventedgasfueledequipmentshallnot

approvetheinstallationunless,uponinspection,theinspector

observescarbonmonoxidedetectorsandsignageinstalled

inaccordancewiththeprovisionsof248CMR5.08(2)(a)1

through4.

Thisappliancerequiresaspecialventingsystem.If

BAYAIR30CNVENTorBAYVENT200Bareused,acopyof

theinstallationinstructionsforthekitshallremainwiththe

applianceorequipmentatthecompletionofinstallation.The

ventingsysteminstallationinstructionscanbeobtainedfrom

themanufacturerbywritingtothefollowingaddress:

ResidentialSystems

6200TroupHighway

Tyler,TX75707

Attention:ManagerofFieldOperationsExcellence

The manufacturer has a policy of continuous data improvement and it reserves the right to change design and specifications without notice. We are

committed to using environmentally conscious print practices.

18-CH83D1-1A-EN 01 Jul 2020

Supersedes 18-CH83D1-1 (December 2015)

About Trane and American Standard Heating and Air Conditioning

Trane and American Standard create comfortable, energy efficient indoor environments for residential applications.

For more information, please visit www.trane.com or www.americanstandardair.com

Otros manuales de Suministros para calderas de Trane

Trane

Trane BAYHTRV108 Instrucciones de montaje

Manuales populares de Suministros para calderas de otras marcas

Beretta

Beretta B23 Manual de usuario

Fröling

Fröling Lambdatronic S 3200 Manual de usuario

CleaverBrooks

CleaverBrooks Hawk 1000 Manual de usuario

De Dietrich Thermique

De Dietrich Thermique AD252 Manual de usuario

NTI

NTI 83112-1 Manual de usuario

TriangleTube

TriangleTube CCRKIT32 Manual de usuario

Bosch

Bosch CB 28 Manual de usuario

Volt Polska

Volt Polska GREEN BOOST 3000 Manual de usuario

Immergas

Immergas 3.031483 Manual del producto

DeDietrich

DeDietrich EA 92 Manual de usuario

AFRISO

AFRISO PrimoBox ACB 910 Hoja de especificaciones

Beretta

Beretta CONNECT BASE MIX 1 LE Manual de operación e instalación

tado°

tado° Elexia Manual de usuario

TriangleTube

TriangleTube PSRKIT84 Manual de usuario

Buderus

Buderus Logamax plus GB142-24 Manual de usuario

Bosch

Bosch 7738003218 Manual de usuario

Immergas

Immergas VICTRIX PRO 35 Manual de usuario

AFRISO

AFRISO GAK Manual de usuario