Trakm8 RoadHawk DVR4000 Manual de usuario

RoadHawk

DVR4000/DVR8000

Set-up Guide

JAN18034

OCT18015

1 Remote Layout

Remark: When the DVR is in alarm condion, the remote control is invalid.

① Go to menu

② Return

Record

Enter the sub-menu to set and conrm

Playback on the mobile DVR

① Stop when recording or during playback

② Delete

Pause/Play during playback

Fast-forward during video playback, Press again

to speed up.

Rewind uring video playback. Press again to skip

by 10 seconds

Enter PTZ control mode.

Control PTZ Zoom

Control PTZ focus

Mute key to turn on or turn o audio output dur-

ing playback videos with audio.(The audio input

of the playback device must be connected to the

audio output of the DVR.)

① Exit video playback or backup.

② Exit from PTZ mode.

① Upward for MENU selecon.

② ‘UP’ direcon for PTZ control mode.

① Downward for MENU selecon.

② ‘Down’ direcon for PTZ control mode.

① Towards le for MENU selecon or MENU setup.

② ‘Le’ direcon for PTZ control mode.

① Towards right for MENU selection or MENU setup.

② ‘Right’ direcon for PTZ control mode.

① Screen zoom the rst channel video when

surveillance, record

② Enter password or set system password.

③ Shortcut keys, press the rst key shortcut to

switch the number 1, press the second key short-

cut to switch the capital leer a, press the third

key shortcut toggles the lowercase leers a, press

the up and down keys to change value.

① 4 channel display uring surveillance, record

and playback.

② Enter password or set system password.

Press 1, 2, 3, 4, 5, 6, 7, 8 switch to CH1, CH2, CH3, CH4,

CH5, CH6, CH7, CH8

Buons not menoned are not in use.

2 Login

First press .

and then press to enter the default

password 6666.

3 Sub Menu

To select ‘Setup’, ‘Vehicle’ , ‘Other’, ‘System

info’, ‘Log’ and ‘Cong’ opons, please use

the arrow navigaon buons on the remote

control. Pressing the ‘OK’ buon will select

the desired opon.

Then press to enter the main

menu interface.

To select ‘System’, ‘Disk’, ‘Record’, ‘Playback’,

‘Network’ and ‘Alarm’ opons, please use

the arrow navigaon buons on the remote

control. Pressing the ‘OK’ buon will select

the desired opon.

4 Setup Menu

To select ‘Base’, ‘User’ , ‘Serial’, ‘PTZ’, ‘GPS’,

‘G-sensor’ and ‘NTP’ opons, please use

the arrow navigaon buons on the remote

control. Pressing the ‘OK’ buon will select

the desired opon.

Date format: Oer 3 display methods like

‘y/m/d, m/d/y, d/m/y’ for personal habit.

Daylight saving me: On or o.

Date: Adjust the date of HDD recorder

Time: Adjust the me of HDD recorder

Language: Set ‘Chinese’, ‘English’,

‘Portuguese’, ‘Russian’ and ‘French’, have

to restart the DVR aer seng.

Video Mode: Set ‘PAL’ or ‘NTSC’ - requires

system restart.

Delay Time: Shut down aer ignion o

funcon, the default me is 5 secs.

Selectable 30secs to 23.5 hours.

Note: Select the ‘OK’ buon to save any changed

parameters, select the ‘Cancel’ buon to close the

window without saving any changed parameters.

5 Base Menu

Set the System me, TV system, Language, etc.

Enter the menu, then use the navigaonal arrows

on the remote control to select the opons. Then

press the ‘OK’ buon to enter the modicaon

mode. Adjust the number by pressing the

navigaonal arrows on the remote control. Press

the ‘OK’ buon to save aer adjustments.

Press the’Menu’ buon to exit.

6 GPS Sengs (see image) Set to UTC

Set up the communicaon protocol with

external equipment via the serial

sengs screen.

ID Time zone: Dierent by countries, e.g:

China for UTC+08.

GPS Interval: GPS data upload interval,

used with other system interface.

7 G-Sensor

G Sensor-X: 2000mg (default value). This

value will change accordingly if the X

direcon gravity accelerated speed value

is changeable.

G Sensor-Y: 2000mg

(default value, customisable).

G Sensor-Z: 2000mg (default value, this

value will change accordingly if the Z

direcon gravity accelerated speed value

is changeable).

Note: Press the ‘Adjust’ buon to adjust

G-sensor parameters when rst installed.

8 Vehicle Id

Details of car number plate, route and

driver code.

Car ID: Can be showed by English, numbers

or common symbols.

A-person: Set up the driver for the vehicle.

Line Num: The driving route and code.

Driver ID: Set up the driver

code informaon.

9 Video Output

VGA Output: 1920x1080, 1280x720,

1024x768, no output.

Zoom in CH: Choosing which channel to

see each me power is on. This is also useful

when backing the car. E.g. when you choose

CH 1 as the Zoom, CH1will be shown on

screen when you start the device,.

Alarm Phone: Set the acon of alarm or not.

Phone number: Click alarm funcon and

set the phone number for alarm.

6.19 Codec

Channel: Select the channel seng. The

informaon of each channel can be

set independently.

Resoluon: CIF/ HD1/ D1/ 960H/ 720p/

1080p: The le column shows local storage

informaon. The right column shows

network transmission informaon. Local

‘CIF, HD1 and D1’ is oponal. Only ‘CIF’ can

be chosen for network transmission.

Frame: 1-25/30fps.

The le column shows local storage

informaon. The right column shows

network transmission informaon.

Stream mode: Contains Bit Rate and

Variable Bit Rate.

Quality: Video quality seng.

The le column shows the local video

quality (total 192kbps/ 320kbs/ 512kbps/

768kbps/ 1Mbps/ 1.2Mbps/ 1.5bps/

2Mbps/ 3Mbps/ 4Mbps.

The right column showsthe network

transmission quality( total 13 grades,

32kbps/ 48kbs/ 64kbps/ 80kbps/ 112kbps/

144kbps/ 192kbps/ 256kbps/ 320kbps/

384kbps/ 512kbps/ 768kbps/ 1024kbps).

Audio: Select to record with or without audio.

Copy to all: Copy to all channels.

Note: Save aer nishng video parameter

seng. (The DVR will need to be restarted

aer seng).

10 Camera Setup

The video les seng includes ‘codec’,

‘channel’ and ‘record plan’.

12 OSD Setup

Channel: Select the channel seng (the

informaon of each channel could be

set independently).

Channel name: The name of each channel.

OSD: Choose to add the character

informaon or not.

Copy to all: Copy to all channels.

13 Recording Setup

Channel: Select the channel seng. The

informaon of each channel can be

set independently.

Record mode: Real time, event or no record.

File length: The packaged video les length

seng (5/10/15/25/30/60 minutes).

Pre-record: Before the alarm recording

me (none,5 secs,10 secs or 15 secs).

Event REC me: Alarm-triggered video

duraon (30-330 secs oponal,

30secs unit).

Schedule: Customise the record periods

and alarm intervals.

Copy to all: Copy to all channels.

Save: Save aer nishing video parameter

seng. The DVR will need to be restarted

aer seng.

The operang method is similar to the

‘basic sengs’ operang.

14 Sensor Seng

Channel: Main channel. Oponal

alarm inputs.

Enable: Turn on/o means.

Sensor name: Name the alarm.

Trigger level: High or low level trigger of

the alarm.

Linkage: Set up ON/ OFF video

linkage funcon.

OSD: Choose whether to overlay

alarm informaon.

Lock: Never overwrite.

Alarm: Choose whether to overlay

alarm informaon.

Alarm out: Choose whether to alarm out.

Save: Click the save buon to keep the

sengs aer reboong.

15 Overwrite and Format

Disk Name: Display the system-recognised

HDD name.

Overwrite: Choose on and o.

Total Size: Display the total size of HDD.

Free Size: Display the remaining capacity

of HDD.

Free record me: An esmate of your

recording me availability.

Format: Format HDD (only format the

head les of HDD).

Select this item. There is a format interface

aer pressing the ‘OK’ buon. Conrm to

format or cancel to return to the

original interface.

16 Import/Export

Import: Import the

conguraon parameters.

Export: Export the

conguraon parameters.

Renew: Restore the factory parameter.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara digital de Trakm8

Trakm8

Trakm8 RoadHawk DVR8000 Manual de usuario

Manuales populares de Cámara digital de otras marcas

Mercury

Mercury 350K Manual de usuario

Pentax

Pentax Optio LS 465 Manual de usuario

Sanyo

Sanyo VPC-S1085 Manual de usuario

GE SMART A1255 Manual de usuario

Point Grey

Point Grey Gazelle Manual de usuario

Nikon

Nikon COOLPIX A Manual de usuario

Pentax

Pentax P-5 Manual de usuario

BlazeVideo

BlazeVideo A280 Manual de usuario

Sony

Sony MCA-20 Manual de usuario

Sony

Sony Alpha DSLR-A290 Manual de usuario

ATIK Cameras

ATIK Cameras One Manual de usuario

CohuHD Costar

CohuHD Costar 3930 Series Manual de usuario

Leica

Leica M10-R Manual de usuario

FujiFilm

FujiFilm FinePix A700 Manual de usuario

Lorex

Lorex LNZ81P25 Series Manual de usuario

GE J1470S Manual de usuario

Sony

Sony A6700 Guía del usuario

Canon

Canon EOS ELAN7 Manual de usuario