TPG Archer VR600 Manual de usuario

Modem Conguration Guide

VR1600v (Fibre To The Building (FTTB))

Windows 7

IMPORTANT MESSAGE

Your modem has already been pre-conﬁgured, you do not need to follow each step of the set-up guide but should retain

this document in case you need to manually conﬁgure your equipment.

To conﬁgure your device with your wireless password including changing your wireless password, please

proceed to step 4.

Contents

1. Physical Connection

2. Network Conﬁguration

3. Conﬁguring Internet

4. Conﬁguring Wireless

5. Change of Password

1. PHYSICAL CONNECTION

Have your modem powered on and connected directly to your PC via Ethernet Cable before you begin, as these

instructions are based on wired Ethernet connection

For further information, please see wiring diagram and instructions for your FTTB connection below.

• TPG Fibre To The Building

2. NETWORK CONFIGURATION

PPPoE connection does not require you to have an IP address or DNS settings manually encoded on your network card.

PPPoE connection uses authentication to establish the Internet connection and once connected your modem will be

assigned an IP and DNS settings from TPG.

To begin, your PC needs to receive a private IP address from the modem. Most modems have DHCP enabled by default

that will take care of this.

VR1600v

Modem Conguration Guide VR1600v

C. Click on Internet Protocol Version 4 (TCP/IPv4), and then click

Properties

D. Ensure “Obtain an IP address automatically” is selected

E. Ensure “Obtain DNS server address automatically” is selected

F. Click OK

To ensure your Network Card is ready for this, please follow the following steps:

A. Click Start -> Control Panel -> Network and Internet ->

Network and Sharing Center -> Change adapter settings

B. Right click on Local Area Connection and select Properties

Modem Conguration Guide VR1600v

E. Click the Edit button on pppoe_ptm_2_0_d.

D. On the menu on the left side of the page, click

Network to expand the menu and then

click DSL.

C. You will see the home screen shown on the right.

Click the Advanced tab.

3. CONFIGURING MODEM

A. Open your browser and in the address bar type

http://192.168.1.1 and press Enter

B. Enter admin for both the username and password and click Login.

If you have changed the login credentials, please enter the current

username and password for your modem interface.

Modem Conguration Guide VR1600v

I. You can change your Wi-Fi details or keep

the default settings. The default Wi-Fi SSID

(network name) is WiFi-xxxx (xxxx is a random

4 digit alphanumeric code printed on the sticker

underneath your modem). By default, the Wi-Fi

password is printed on a sticker underneath your

modem (Wireless Password/Key). Click Save.

H. On the menu on the left side of the page, click

Wireless.

G. Click the Basic tab.

F. Enter your TPG Username and Password.

Click Save

Modem Conguration Guide

F. You should now see your status as ‘Connected’.

E. Click OK.

D. You will now be prompted to enter your WPA Key /

wireless password. By default, the WiFi password is

printed on a sticker underneath your modem (WLAN Key).

if you did not change it on the modem.

C. Find the SSID (network name) of your modem and click

Connect. By the default, the network name should be

WiFi-xxxx (xxxx is a random 4 digit alpha numeric code).

Note: You may notice there are two wireless networks

present. You may connect to either of these.

B. Right click on Wireless Network Connection and

click ‘Connect/Disconnect’

VR1600v

5. CHANGE OF PASSWORD

For security purposes we highly recommend that you change your password if you are using your default or if you believe your

password security has been compromised. For password information, please visit www.tpg.com.au/support.

PLEASE NOTE:

Each time your modem is powered on, it will initialize this automated authentication process after which your modem will

receive a public dynamic IP address (ﬁxed or dynamic depending on your plan) and DNS settings from TPG.

13 14 23tpg.com.au/support

4. CONFIGURING WIRELESS

To use Wireless, ensure that you already have set up your wireless adapter.

A. Click Start -> Control Panel -> Network and Internet -> Network and Sharing Center -> Change adapter settings

WiFi-Y659

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario