TPC Mirage 2.0 Manual de usuario
1
www.tpcdental.com
Mirage Dental Delivery Unit
Model 2.0 Installation Instructions
TPC
851 S. Lawson St.
City Of Industry, CA 91748
P626-810-4337 Fax 626-810-4245
2
www.tpcdental.com
Table on Contents: Page
GENERAL INFORMATION
Unpacking and Inventory 3
Installation and coordination 4
Optional Cuspidor Installation 10
Cuspidor Plumbing Connections 11
Junction Box Connections 12
Post Mount Utility Center Adjustments 13
Pressure Adjustments / Tension Screws 13
Delivery Head / Tilt Adjustments 14
Tubing / Connections 15
Floor Template 16
3
www.tpcdental.com
Unpacking and Inventory
Each Mirage delivery unit will contain the following items in each box.
1. Flex arm box. This is the largest box that you will receive with the delivery unit.
• Delivery unit flex arm
• Assistance arm
• Light post
• Skid Pad
• Cosmetic beauty ring
2. Post mount utility center
• Utility center
• Master controls attached to the umbilical for air and water.
• Wet dry foot control
• HEV/SE valves with tubing
• Water Bottle (1000 ml)
3. Optional 2000-C Cuspidor
• Cuspidor
• Bowl rinse spout
• Cuspidor bowl strainer
4. Separate Junction box. For use with chairs that don’t have an integrated pump cover /
junction box.
• Junction box cover
• Junction box frame.
• If at any time you have questions regarding
your installation please don’t hesitate to
contact TPC toll free @ 800-560-8222 or via E-
mail @ [email protected]
4
www.tpcdental.com
Installation Instructions
1. Locate the four mounting bolts that were included with your dental chair adaptor. Secure
bracket as shown in the image below. This installation will vary with different char
manufactures.
2. Leveling Chair bracket.
• The chair bracket has a total of 8 set screws.
• Use the lower set screws to adjust the PMU left, right, front and back. This will make
large adjustments to the tilt of the post that is inserted into the bracket cup.
• Use the upper set screws to make fine adjustments and lock the post in place.
• Once the post is level you may fasten the set screws tightly to ensure the post stays level.
If your post is not level your unit will not be level and the flex arm will drift.
5
www.tpcdental.com
3. Loosen the 8 leveling set screws, and then place the PMU (Post mount utility center) in
the cup of the chair bracket. Figure 3.1 Center the mounting post in the cup. Also verify if
the PMU is aligned straight with dental chair armrest.
4. Verify the PMU is level before tightening the set screws on chair bracket. There are 8 set
screws that will be used for leveling. If the PMU is not level the unit arms may drift.
Small adjustments to the set screws will level the PMU. Level the PMU in the following
directions. (left to right and front to back).
Figure 3.1
6
www.tpcdental.com
5. Remove the PMU side cover. To remove it, pull on the lower lip to detach its magnetic
connection. Place it out of the way so it does not get damaged. This side cover will
remain detached until the end of the installation.
6. Remove the plastic covers on the top of the PMU box Figure 6.1. Install the light post as
shown in the middle hole on the PMU side box Figure 6.2. Secure in place by tightening
the 4mm Allen set screw inside the PMU box Figure 6.3.
Figure 6.1
Figure 6.2
Figure 6.3
7
www.tpcdental.com
7. Remove the cosmetic rings from the side box figure 7.1. Place the cosmetic over the end
of the delivery unit flex arm Figure 7.2. Once in place, route all lines and feed them
through the bushing assembly shown in figure 7.3. Verify that the arm seats completely
down on the bushing assembly. Lower the cosmetic ring to cover the seam between the
arm and utility center cover.
8. Route the delivery system foot control and feed it through the bottom of the PMU figure
8.1. Make the following connections from your foot control to the tubing within the PMU
side box. Large yellow to Grey on foot control X2. Small grey on foot control to the clear
tubing to unit head for water relay connection. Figure 8.2.
Figure 7.1
Figure 7.2
Figure 7.3
Figure 8.1
Figure 8.2
8
www.tpcdental.com
9. Tubing connections in Post mount utility center.
• Orange from umbilical to Orange in flex arm. Signal Air return from master
switch.
• Black from umbilical to black in flex arm. Return signal air from master control.
• Small Grey from foot control to clear tubing in flex arm. Water relay signal air.
• Blue from umbilical to blue in flex arm. City water supply from J box to PMU
9
www.tpcdental.com
10. Installing assistance side touch pad. Remove the 5 screws that secure the covers together
Figure 10.1. Open the assistance holder and remove the 4 additional screws that attach
the bottom of the holder to the support frame in figure 10.2. Route the touchpad wire as
shown in figure Attach the touchpad bracket shown in figure 10.3.
11. Install the lower assistance cover over the 2 screws from the touchpad bracket. Install the
washers and nylon nuts for the touchpad screws shown in figure 11.1. Connect the Molex
connector from the touchpad to the wire harness shown in figure 11.2. Re-install the 5
screws to secure the top cover back onto assistance holder in figure 11.3.
12. Take the white 13 pin Molex connector that travels from the flex arm and route it to the
backside of the PMU to the PCB board Figure 12.1 / 12.2. Connect the harness to the
main PCB as shown in figure 12.3.
Figure 10.1
Figure 10.2
Figure 10.3
Figure 11.1
Figure 11.2
Figure 11.3
Figure 12.1
Figure 12.2
Figure 12.3
10
www.tpcdental.com
13. Install the operatory light onto light post. Ref operatory light installation manual for
specific installation instructions for your setup. Connect the power cable from the LED
light wire harness to the terminal bus bar in the side box. Figure 13.1shows the terminal
bus bar. Connect the power to the terminals that says light Figure 13.2 / 13.3. This bus
bar power is controlled via the touchpad. If you don’t require a touchpad controller
operatory light, you can connect the power to the ports on the bus bar labeled 24V. this
will provide constant 24V power to the LED operatory light.
14. Connect the low voltage wire from the unit flex arm to the terminal Bus bar in the side
box figure 14.1. This will provide 24VAC to the unit head termina bus bar if low voltage
applications are required. See red and black wires piggybacked on the 24V terminal
Figure 14.1. unit head terminal block show in figure 14.2
Figure 13.1
Figure 13.2
Figure 13.3
Figure 14.1
Figure 14.2
Tabla de contenidos
Otros manuales de Equipo dental de TPC
TPC
TPC L700 Lucent Dental Light Manual de operación
TPC
TPC PC 2530 Manual de usuario
TPC
TPC ProClean Extra Oral Suction Manual de usuario
TPC
TPC LED 55N Manual de usuario
TPC
TPC LED 55BN Manual de usuario
TPC
TPC Amalgamator D-650 Manual de usuario
TPC
TPC Amalgamator D-650 Manual de instrucciones y seguridad
TPC
TPC PC2630 Manual de usuario
TPC
TPC PC2635 Guía de inicio rápido
TPC
TPC Laguna 2.0 Manual de usuario
Manuales populares de Equipo dental de otras marcas
Vatech
Vatech EzRay Air VEX-P300 Manual de usuario
KaVo
KaVo GENTLEpower LUX Contra-angle 25 LP Manual de usuario
DENTSPLY
DENTSPLY SmartLite Focus Manual de usuario
LM
LM ProPower CombiLED Manual de usuario
Owandy Radiology
Owandy Radiology RX-AC Manual de usuario
mectron
mectron Piezosurgery Manual de usuario
