TP-Link TL-WR940N Manual de usuario

Note Please use only wired network connections to configure the Router.

Turn off all of your network devices, including your computer, Modem and the

uter.

Connect your computer to the

Port labeled 1~4 on the Route

with an Ethernet cable.

Plug the provided Powe

dapter into the Power jack on

the back of the Router and the

other end to a standard

electrical wall socket.

Connect the WAN port on your

Router to the Modem’s LAN

port with an Ethernet cable.

Solid light

Flashing

Flashing or solid light

Turn on all of your network devices and then check to see if the LEDs of the

Router display normally as the digram below describes.

Note To configure the device, you can either run the Resource CD (method one),

or run the Web based Quick Setup Wizard (method two). TP-LINK strongly

recommends that you run the Resource CD.

Flashing or solid light if the

corresponding port is connected

Note If the LEDs display abnormally, please check to see if all the cable

connectors (power adapter and Ethernet cable) are well connected to you

device.

The configuration has now been completed. Please skip to step 3 Testing the

Internet Connection.

Insert the provided Resource CD

into your CD-ROM drive.

The Easy Setup Assistant

will automatically prompt you

on your computer’s screen.

Please select your

product model and click

Easy Setup Assistant

Click START, and then follow

the step-by-step instructions

until you complete the

configuration

Click OK

Click Quick Setup

A dialog box will prompt you fo

the User name and Password.

Enter the default values and click

OK.

User name: admin

Password: admin

Note If the dialog box does not pop up, please refer to T3 in the

Troubleshooting guide. T2 will help you if you forget the password.

Open your web browser,

type in 192.168.1.1 in the

address field and press

Enter

The web management page will

display after a successful login.

Click Next

Select Auto Detect

Click Next

Internet Parameters Configuration

Note

This page will then display.

Waiting for the Router to detect

the connection type.

If PPPoE is detectedǈyou will be popped up the screen as shown in A. Please

proceed to AǗ

If Static IP is detectedǈyou will be popped up the screen as shown in B. Please

skip to BǗ

If Dynamic IP is detectedǈyou will be popped up the screen as shown in

Wireless Settings Configuration. Please skip to Wireless Settings

Configuration.

1. Make sure the cable is securely plugged into the WAN port before

detection.

2. If the connection type your ISP provided is PPTP, L2TP or BigPond (o

Heart Beat Signal), you must go to “Network > WAN” to configure you

connection type manually.

A Configuration for PPPoE

B Configuration for Static IP

Wireless Settings Configuration

This page will then display.

After completing the above configuration, please proceed to Wireless Settings

Configuration.

Enter the IP Address,

Gateway, DNS provided

our ISP manuall

Click Next

Enter the Username and

Password provided by your

ISP

Click Next

After completing the above configuration, please skip to Wireless Settings

Configuration.

This page will then display.

Choose a unique name for your

wireless network; however,

choose a name that is easily

remembered by the network

users. You can also keep default

settings without the device being

affected

Keep the default setting:

Enable Wireless. If you want

to disable wireless, please

select Disable

Select your region from the drop-down list

Click Next

Or if wireless settings have been changed

The basic settings for your Router are completed. Please open the web browser and

log on to the following websites:

http://www.tp-link.com

http://www.google.com

If the above websites can be accessed, it indicates that your Router has been

configured successfully and you can begin to enjoy the Internet. If the website

cannot be accessed, please refer to “T4. What can I do if I cannot access the

Internet?” in the Troubleshooting guide.

Note The wireless security has not yet been configured in the above steps. You

are suggested to finish this configuration first and then refer to

ppendix

Wireless Security Setup to configure the wireless security.

The above configurations only need to be set once. If you want other

computers in your network to access the Internet, please connect the desired

computer to the router directly. If the additional computer can not access the

Internet, please set that computer referring to “T3. What can I do if I cannot

access the web-based configuration page?” in the Troubleshooting

guide.

For advanced configurations, please refer to the User Guide on the

Resource CD provided.

Click Finish

Click Reboot

Note

T1. How do I restore my Router’s configuration to its factory default

settings?

T2. What can I do if I don’t know or forgot my password?

1) Restore the Router’s configuration to its factory default settings. If you don’t

know how to do that, please refer to section T1.

2) Use the default user name and password: admin, admin.

3) Try to configure your Router once again by following the instructions in the

previous steps of the QIG.

T3. What can I do if I cannot access the web-based configuration page?

1) Configure your computer’s IP Address.

For Windows XP OS

Go to Start > Control Panel,

you will then see the following

page.

Click Network and Internet

Connections

With the Router powered on,

press and hold the Reset button

on the rear panel for 8 to 10

seconds before releasing it.

Hold it for 8 to 10 seconds

Once the Router is reset, the current configuration settings will be lost and

you will need to re-configure the router.

1 2 3 4

WAN

RESET

POWER

Double-click Internet

Protocol (TCP/IP)

Click Properties

Click Network

Connections

Right-click Local

Area Connection

Select Obtain an IP

address automaticall

Select Obtain DNS

server address

automatically

Click OK

Otros manuales para TL-WR940N

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Enrutador inalámbrico de TP-Link

TP-Link

TP-Link Archer BE550 Manual de usuario

TP-Link

TP-Link TL-WR841N Manual de usuario

TP-Link

TP-Link deco W7200 Manual de usuario

TP-Link

TP-Link TD-W8968 Manual de usuario

TP-Link

TP-Link M5350 Manual de usuario

TP-Link

TP-Link TL-WR902AC Manual de usuario

TP-Link

TP-Link TD-W8920G Manual de usuario

TP-Link

TP-Link TD-W8960N Manual de usuario

TP-Link

TP-Link TD-W8968 Manual de usuario

TP-Link

TP-Link TL-PA7017P Manual de usuario

TP-Link

TP-Link TL-WR700N Manual de usuario

TP-Link

TP-Link TL-MR3420 Manual de usuario

TP-Link

TP-Link Deco M5 Manual de usuario

TP-Link

TP-Link TL-WR641G Manual de usuario

TP-Link

TP-Link TL-WR941N Manual de usuario

TP-Link

TP-Link TX-W6961N Manual de usuario

TP-Link

TP-Link TD-W8960N Manual de usuario

TP-Link

TP-Link TD-W8960N Manual de usuario

TP-Link

TP-Link TD-W8901GB Manual de usuario

TP-Link

TP-Link Archer C86 Manual de usuario

TP-Link

TP-Link Archer AX3000 Manual de usuario

TP-Link

TP-Link Archer AX5400 Pro Manual de usuario

TP-Link

TP-Link TL-WR847N Manual de usuario

TP-Link

TP-Link TL-WR842ND Manual de usuario

Manuales populares de Enrutador inalámbrico de otras marcas

Milesight

Milesight UG67 Manual de usuario

Airlogic

Airlogic AirSync Class 1 Manual del propietario

Samsung

Samsung WCH730B Manual de usuario

TELEFONICA

TELEFONICA USB Adapter Manual de usuario

NETGEAR

NETGEAR PowerLINE WiFi 1000 Series Manual de usuario

Askey

Askey RAC2V1K Manual de usuario

Alloy

Alloy WLF2454AP-S Manual de usuario

NETGEAR

NETGEAR WNR2000v4 Manual de usuario

Hama

Hama 53120 Manual de usuario

Intellinet

Intellinet 524582 Manual de usuario

Asus

Asus RT-N10P Manual de usuario

D-Link

D-Link DIR-506L Manual de usuario

Sapido

Sapido GR297n Manual de usuario

Asus

Asus DSL-N55U Manual de usuario

AMTC

AMTC WR7502 Manual de usuario

Compaq

Compaq CP-2W - iPAQ Connection Point Manual de usuario

SMC Networks

SMC Networks WBR14-N2 FICHE Manual de usuario

Draytek

Draytek Vigor2120 Series Manual de usuario