TP-Link TL-WDR3600 Manual de usuario
TP-Link TL-WDR3600
Quick Install Guide
Sharedband Router Setup Steps
1) Remove the Sharedband routers from their packaging (DO NOT remove the protecve lm
from the routers for the rst 30 days) and place them in a suitable locaon
2) Use the included short Ethernet cable(s) to connect the routers’ yellow ’LAN’ ports in
either of these two conguraons:
a) The recommended setup is to connect the Sharedband routers together via an
un-managed switch
b) However you can connect the Sharedband routers together with an Ethernet cable (daisy
chained)
3) Use the included long Ethernet cables to connect each routers’ blue ‘Internet’ port to the
modems/routers provided by your ISP
4) Use the included power adapters to connect each router’s ’Power’ socket to a mains
power outlet
5) Ensure that the ‘On/O’ buon is depressed on all routers
TP-Link TL-WDR3600 2www.sharedband.com
Verify Successful Setup
6) Use an Ethernet cable to connect a computer to any unused yellow ‘LAN’ port of the
router you would like to verify has been successfully setup
7) Please note the node idener which is a unique single digit number clearly marked on
the underside of the router
8) Open a web browser and visit the IP address of the connected router. These are
hp://192.168.3.1 if connecng to node idener 1, hp://192.168.3.2 if connecng to
node idener 2 etc…
9) When prompted for sign in credenals , please input the following:
Username: admin Password: Bonding123 (we recommend that you change this password)
10) In the menu posioned at the le of the displayed web page, select ‘Status’
11) If this router has been successfully setup, items within the ‘Service Status’ panel will be
displayed green in colour and report as follows:
For informaon, the above listed items make the following checks:
Modem Connecon Status - connecon through your ISP
Aggregaon Server Status - connecon to our data centre
Roung Mode - method by which router is able to communicate:
WAN and Community: This router is connected to the aggregaon server directly and
at least 1 other Sharedband router in its community
WAN Only: This router is not connected to other routers in its community (see step 2
to resolve)
Community Only: This router is not connected to the aggregaon server directly (see
page 4 for assistance)
No network available: This router is not connected to the Sharedband aggregaon
server and other routers in its community (see page 4 for assistance)
12) Repeat above steps 6-11 for all of the remaining routers in the community
TP-Link TL-WDR3600 3www.sharedband.com
Troubleshoong ‘Service Status’
If the WAN-side routers (provided by your ISP) you are connecng to the Sharedband
routers don't operate DHCP, you will need to set a stac IP on each Sharedband router to
enable communicaon. The following guidance explains how to achieve this:
a) Connect a computer to the aected Sharedband router
b) Open a web browser and visit the IP address of the router
c) Sign in to the router when prompted
d) In the menu select ‘Sengs’
e) Select ’WAN connecon setup (Ethernet)’ to access the ‘IP Addressing’ panel as shown
f) In the ’IP Addressing Mode’ drop down, select ‘Stac IP’
g) Input the appropriate IP address into the ‘IP Address’ eld. An appropriate address is one
that is unique, in the same subnet as your WAN-side router and not in the 192.168.3.X
subnet. For example, if the WAN-side router’s IP address is 192.168.1.1 an appropriate IP
address to input for the Sharedband router would be 192.168.1.X (where X is any number
between 2 and 254). If you need assistance in determining the WAN-side router’s IP
address, please refer to any supplied documentaon or contact its supplier or
manufacturer
h) Ensure that the ‘Subnet Mask’ is set to 255.255.255.0
i) Input the IP address of the WAN-side router into the ‘Default Gateway’ eld
j) Input the IP address of the WAN-side router or an alternave desnaon of your choice
into the ‘DNS Server’ eld
k) Click the ’Save and reboot’ buon at the boom of the page
l) Once the Sharedband router has restarted, repeat steps 8-11 (on page 3) to verify
successful setup
More Informaon
Both our helpful knowledgebase and support ckeng system are accessible online at:
hp://support.sharedband.com
www.sharedband.com 4TP-Link TL-WDR3600
Otros manuales para TL-WDR3600
3
Tabla de contenidos
Otros manuales de Enrutador inalámbrico de TP-Link
TP-Link
TP-Link TL-MR3220 Manual de usuario
TP-Link
TP-Link Archer AX55 V1 Manual de usuario
TP-Link
TP-Link TL-WR641G Manual de usuario
TP-Link
TP-Link Archer C64 Manual de usuario
TP-Link
TP-Link WR820N(EU) Manual de usuario
TP-Link
TP-Link TL-WR710N Manual del propietario
TP-Link
TP-Link M7200 Manual de usuario
TP-Link
TP-Link Archer VX1800v Manual de usuario
TP-Link
TP-Link TL- WR740N Manual de usuario
TP-Link
TP-Link Archer C7 Manual de usuario
TP-Link
TP-Link TL-WN8200ND Manual de usuario
TP-Link
TP-Link TL-WR841HP Hoja de información del producto
TP-Link
TP-Link Archer AX72 Manual de usuario
TP-Link
TP-Link Archer D9 Manual de usuario
TP-Link
TP-Link TL-WR843N Manual de usuario
TP-Link
TP-Link TL-WR842ND Manual de usuario
TP-Link
TP-Link AC1350 Manual de usuario
TP-Link
TP-Link TL-MR3220 Manual de usuario
TP-Link
TP-Link Archer D20 Manual de usuario
TP-Link
TP-Link Archer AX53 Manual de usuario
