TP-Link TL-WA701ND Manual de usuario

Connect to the Access Point with

the Ethernet cable or via wireless.

The default SSID of the Access

Point is TP-LINK_ XXXXXX. The

XXXXXX is the last 6 characters

of the Access Point’s MAC

address.

Plug the provided power adapter

into the power jack on the back of

the Access Point, and the other

end to a standard electrical wall

socket. Then press the ON/OFF

button to power on the device.

Turn on all of your network devices and then check to see if the LEDs on the

Access Point display normally as the diagram below describes.

Note If the distance between the outlet and the Access Point is too long to supply

the power, you can refer to the Power over Ethernet (PoE) solution in

Appendix A: With PoE Setup on page 13.

Solid light

Flashing

Solid light or flashing

Flashing if the Wireless

Radio function is enabled

Wireless Settings

dialog box will prompt you for the

User name and Password.Ente

the default values and click OK.

Note If the dialog box does not pop up, please refer to T3 in the Troubleshooting

guide on page 10. T2 will give you some help if you forget the password.

User name: admin

Password: admin

Click OK

Note If the LEDs display abnormally, please check to see if all the cable

connectors (power adapter and Ethernet cable) are well connected to you

device.

fter successfully logging in, the

Quick Setup page will display.

Open your web browser, type in

192.168.0.254 in the address

bar and press Enter

Click Next

Note If you click Exit and choose to configure the AP manually on your own need,

please note that the DHCP is enabled during the configuration, it is essential

to disable DHCP when all the settings are finished.

A. Access Point Mode

Introduction

In this mode, the product will act as a wireless central hub for your wireless LAN

clients, giving a wireless extension for your current wired network.

Settings

1. Create an easy-to-remember name for your wireless network here.

2. Select Most Secure (WPA/WPA2-PSK) mode and enter a password below to

prevent unauthorized access to your AP.

3. Input a password here.

For Access Point mode, please refer to part A on page 3.

For Multi-SSID mode, please refer to part B on page 4.

For Repeater(Range Extender) mode, please refer to part C on page 4.

For Bridge with AP mode, please refer to part D on page 6.

For Client mode, please refer to part E on page 7.

The Operation Mode page will

appear then. The TL-WA701ND

supports up to five operation

modes.

Select the operation mode

based on your need

Click Next

After the settings above, please go to Network Settings on page 8 to continue

the configuration.

B. Multi-SSID Mode

Introduction

In this mode, the product can be assigned up to four SSIDs to work with your VLAN.

Settings

After the settings above, please go to Network Settings on page 8 to continue

the configuration.

C. Repeater (Range Extender) Mode

Introduction

In this mode, the product can extend the coverage of another wireless Access Point

or Router. The universal repeater mode is for the wireless Access Point or Router

which does not support WDS function.

Note For the configuration of VLAN, please refer to the User Guide on the

Resource CD.

Click Next

You can create up

to 4 SSIDs and

rename them here.

Configure the

wireless security

for each SSID here.

Click Save to apply

the current security

settings for the

selected SSID.

Settings

After the settings above, please go to Network Settings on page 8 to continue

the configuration.

Select the repeater

mode, for example

Universal Repeater.

Click Survey

The window displaying a list of available SSIDs will appear.

You will then return to the

previous page.

Find the SSID of the

root Access Point /

Router that you want to

repeat, and then click

Connect in the

corres

ondin

row.

Select the security

mode and enter the

password that is the

same as on your router

or access point.

Click Next

Note The setup for WDS Repeater mode is similar to that of Universal Repeate

mode.

D. Bridge with AP mode

Introduction

In this mode, the product can wirelessly connect two or more remote LANs together.

Settings

Click Survey

The window displaying a list of available SSIDs will appear.

Find the SSID of the

root Access Point /

Router that you want to

bridge, and then click

Connect in the

corresponding row.

After the settings above, please go to Network Settings on page 8 to continue

the configuration.

E. Client Mode

Introduction

In this mode, the product will act as a wireless adapter to connect your wired devices

(eg. PC, Xbox, PS3, etc. ) to a wireless network.

Settings

Click Next

Enter the password

that is the same as on

the remote AP.

Name the bridge AP

here.

Click Next

Click Survey

You will then return to the

previous page.

After the settings above, please go to Network Settings on page 8 to continue

the configuration.

Network Settings

Find the SSID of the

Access Point / Router

or WISP, and click

Connect in the

corresponding row.

Click Next

Select the security

mode and enter the

password that is the

same as on the root

AP.

Note For advanced configurations on this page, please refer to the User Guide on

the Resource CD.

Click Next

The Network Setting

page will appear then. It

is recommended that

you keep the default

settings on this page.

The window displaying a list of available SSIDs will appear.

You will then return to the

previous page.

Congratulations! You have completed the setup.

Click OK

Note To change to another mode, please refer to T3 in Troubleshooting on page

10 to assign a static IP address 192.168.0.100 for your computer first before

logging in the management page.

Click Reboot

Check your settings

and click Save to save

your settings for future

reference

Wait until the router

restarts successfully.

The Finish page will

appear then. Here takes

the settings for Access

Point mode for example.

T1. How do I restore my Access Point’s configuration to its factory default settings?

T2. What can I do if I forget my password?

1) Restore the Access Point’s configuration to its factory default settings. If you

don’t know how to do that, please refer to previous section T1;

2) Use the default user name and password: admin, admin;

3) Try to reconfigure your AP by following the instructions of this QIG.

T3. What can I do if I cannot access the web-based configuration page?

Assign a static IP address 192.168.0.100 for your computer first before logging in the

management page. Here takes the procedures in Windows 7 for example.

With the Access Point powered on,

use a pin to press and hold the

RESET button on the rear panel fo

8 to 10 seconds before releasing it.

Once the Access Point is reset, the current configuration settings will be lost

and you will need to reconfigure the Access Point.

Note

Go to Start > Settings > Control

Panel, and then you will see the

following page.

Click View network

status and tasks

Hold it in for 8 to 10 seconds

Otros manuales para TL-WA701ND

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de TP-Link

TP-Link

TP-Link TL-WA7510N Manual de usuario

TP-Link

TP-Link Auranet EAP110 Manual de usuario

TP-Link

TP-Link Omada EAP650 Manual de usuario

TP-Link

TP-Link CPE605 Manual de usuario

TP-Link

TP-Link CAP1200 Manual de usuario

TP-Link

TP-Link Auranet EAP120 Manual de usuario

TP-Link

TP-Link AURANET EAP110-Outdoor Manual de usuario

TP-Link

TP-Link TC-7610 Manual de usuario

TP-Link

TP-Link TL-WA5210G Manual de usuario

TP-Link

TP-Link EAP265 Manual de usuario

TP-Link

TP-Link TL-WA701ND Manual de usuario

TP-Link

TP-Link Auranet EAP115 Manual de usuario

TP-Link

TP-Link CPE Series Manual de usuario

TP-Link

TP-Link Omada EAP245 Manual de usuario

TP-Link

TP-Link Omada TPL-EAP225 Manual de usuario

TP-Link

TP-Link Auranet EAP330 Manual de usuario

TP-Link

TP-Link TL-WA7210N Manual de usuario

TP-Link

TP-Link TL-WA3001 Manual de usuario

TP-Link

TP-Link Omada EAP115 Manual de usuario

TP-Link

TP-Link Auranet EAP110 Manual de usuario

TP-Link

TP-Link TL-WA5210G Manual de usuario

TP-Link

TP-Link AURANET CAP300-Outdoor Manual de usuario

TP-Link

TP-Link Omada EAP225-Wall Manual de usuario

TP-Link

TP-Link TL-WA901ND Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

Draytek

Draytek VIGORAP 902 Manual de usuario