TP-Link JetStream T3700G-52TQ Manual de usuario

Business Networking Solution

Installation Guide

JetStream Stackable L3 Managed Switch

T3700G-52TQ

IAbout this Installation Guide

About this Installation Guide

This Installation Guide describes the hardware characteristics, installation methods and the points that should

be attended to during the installation. This Installation Guide is structured as follows:

Chapter 1 Introduction.

This chapter describes the external components of the switch.

Chapter 2 Preparing For Installation.

This chapter illustrates the safety precautions before installing the switch.

Chapter 3 Installation.

This chapter illustrates how to install the switch.

Chapter 4 Lightning Protection.

This chapter illustrates how to prevent lightning damage.

Chapter 5 Connection.

This chapter illustrates how to do the physical connection of the switch.

Chapter 6 Configuration

This chapter instructs you to configure the switch via Web Interface and CLI commands.

Appendix A Troubleshooting.

Appendix B Hardware Specifications.

Audience

This Installation Guide is for:

Network Engineer Network Administrator

Conventions

• The figures in Chapter 2 to Chapter 4 are for demonstration purposes only. Your switch may differ in

appearance from that depicted.

• This Guide uses the specific formats to highlight special messages. The following table lists the notice icons

that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may result in device damage.

Remind to take notice. The note contains the helpful information for a better use of the product.

Related Document

The User Guide and CLI Reference Guide of the product are provided on the resource CD. To obtain the latest

product information, please visit the official website:

http://www.tp-link.com

JetStream Stackable L3 Managed Switch

II Contents

Contents

Chapter 1 Introduction —————————————————— 01

1.1 Product Overview.........................................................................01

1.2 Appearance....................................................................................01

Chapter 2 Preparing For Installation ———————————— 05

2.1 Package Contents .......................................................................05

2.2 Safety Precautions ......................................................................05

2.3 Installation Tools...........................................................................07

2.4 Installation & Connection Flow................................................07

Chapter 3 Installation ——————————————————— 09

3.1 Installing the Switch on a Desktop ........................................09

3.2 Installing the Switch Into a 19-inch Rack ............................09

3.3 Installing & Removing the Power Supply Module .............10

3.4 Installing & Removing the Interface Card (Optional) ......11

3.5 Stacking Using Interface Card on Rear Panel ...................12

Chapter 4 Lightning Protection —————————————— 14

4.1 Cabling Reasonably.....................................................................14

4.2 Connect to Ground ...................................................................... 16

4.3 Equipotential Bonding ................................................................17

4.4 Use Lightning Arrester ...............................................................18

Chapter 5 Connection —————————————————— 20

5.1 Ethernet Port..................................................................................20

5.2 SFP/SFP+ Port ...............................................................................20

5.3 Console Port ..................................................................................20

5.4 Verify Installation..........................................................................21

5.5 Power On ......................................................................................... 22

5.6 Initialization.....................................................................................22

Chapter 6 Conguration—————————————————— 23

6.1 Congure the Switch via GUI ...................................................23

6.2 Congure the Switch Using CLI..............................................24

Appendix A Troubleshooting ———————————————— 27

Appendix B Hardware Specications ————————————— 28

JetStream Stackable L3 Managed Switch

01Introduction

Chapter 1 Introduction

1.1 Product Overview

T3700G-52TQ is an L3 managed switch that features advanced L3 routing, 10Gbps wire-speed,

physical stacking and removable power supply module and fan module, designed to meet the needs

of convergence layer. T3700G-52TQ is ideal for large businesses, campuses or SMB networks

requiring an outstanding, reliable and affordable 10 Gigabit solution.

T3700G-52TQ supports stacking of up to 8 units, thus providing flexible scalability and protective

redundancy for your networks. Moreover, aiming to better protect your network, T3700G-52TQ

supports 2 power supply modules. T3700G-52TQ can fully implement resilient scalable networks

due to its advanced features such as OSPF, VRRP, IGMP and PIM DM/SM.

1.2 Appearance

■Front Panel

The front panel of the switch is shown as the following figure.

Figure 1-1 Front Panel

LEDs 10/100/1000Mbps

RJ45 Port

SFP+ PortSFP Port

Micro-USB

Console Port

Unit ID LED

LEDs

LED Status Indication

PWR1

Green The power supply module connected to the corresponding power

slot works properly.

Yellow The power supply module connected to the corresponding power

slot works improperly.

Off The corresponding power slot is not connected to any power

supply module.

PWR2

Green The power supply module connected to the corresponding power

slot works properly.

Yellow The power supply module connected to the corresponding power

slot works improperly.

Off The corresponding power slot is not connected to any power

supply module.

SYS Flashing (green) The switch works properly.

On/Off The switch works improperly.

JetStream Stackable L3 Managed Switch

02 Introduction

LED Status Indication

MGMT

Green On A 1000Mbps device is connected to the corresponding port, but no

activity.

Flashing Data is being transmitted or received.

Yellow On

A 10/100Mbps device is connected to the corresponding port, but

no activity.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

FAN

Green The fan module works properly.

Yellow The fan module works improperly.

Off No fan module is connected to the switch.

Master On The switch works as master in the stack system, or does not join

any stack system.

Off The switch works as member in the stack system.

Module

On (green) An Interface Card is connected to the switch and works properly.

On (yellow) An Interface Card is connected to the switch, but works improperly.

Off No Interface Card is connected to the switch.

Console On (green) Data is being transmitted or received.

Off No data being transmitted or received for more than 6 minutes.

Link/Act

(Port1-48)

Green On A 1000Mbps device is connected to the corresponding port, but no

activity.

Flashing Data is being transmitted or received.

Yellow On A 10/100Mbps device is connected to the corresponding port, but

no activity.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

49, 50 Green On A 10Gbps device is connected to the corresponding port, but no

activity.

Flashing Data is being transmitted or received.

Off No device is connected to the corresponding port.

M1,M2

Green On A 10Gbps device is connected to the corresponding port of the

Interface Card, but no activity.

Flashing Data is transmitting or received.

Off

■No Interface Card is connected.

■No device is connected to the corresponding port of the

Interface Card.

10/100/1000Mbps Port

Port 1-48 designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding Link/Act LED.

SFP Port

Port 45F-48F, designed to install the SFP transceiver. These four SFP transceiver slots are

shared with the associated RJ45 ports. The associated two ports are referred as a “Combo” port,

which means they cannot be used simultaneously, otherwise only RJ45 port works. The SFP

ports support 1000M SFP module connection only.

JetStream Stackable L3 Managed Switch

03Introduction

SFP+ Port

Port 49-50, designed to install the 10Gbps SFP+ transceiver or SFP+ cables. T3700G-52TQ also

provides an interface card slot on the rear panel to install the expansion card (TX432 of TP-Link

for example). If TX432 is installed, you get another two 10Gbps SFP+ ports.

Micro-USB Console Port

Designed to connect with the USB port of a computer for monitoring and configuring the switch.

The switch has an RJ-45 console port and a micro-USB console port available. Console input is

active on only one console port at a time. By default, the micro-USB connector takes precedence

over the RJ-45 connector.

Unit ID LED

Designed to display the stack Unit ID of the switch. For the switch that does not join any stack

system, it displays its default Unit ID. To modify the default unit number, please log in to the GUI

of the switch and go to Stack→Stack Management→Stack Config page.

■Rear Panel

The rear panel of the switch is shown as the following figure.

Figure 1-2 Rear Panel (1)

Power

PS OK

Fault

PSM150-AC

100-240V~ 50/60Hz 2.5A

Grounding

Terminal

USB 2.0 Interface Management Port

RJ45 Console Port Power Supply Module2Interface Card Slot Power Supply Module1

Note: The Interface Card Slot and Power Supply Module2 are shipped with protective

covers.

Interface Card Slot

Designed to extend the interfaces. You can select a TP-Link Interface Card (TX432 for example)

for your switch if needed. For how to install an Interface Card, please refer to 3.4 Installing &

Removing the Interface Card.

Grounding Terminal

The switch already comes with lightning protection mechanism. You can also ground the switch

through the PE (Protecting Earth) cable of AC cord or with Ground Cable. For detailed information,

please refer to Chapter 4 Lightning Protection.

USB 2.0 Interface

USB 2.0 interface is used to connecting peripheral equipment.

JetStream Stackable L3 Managed Switch

04 Introduction

Management Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or 1000Mbps. It has

a corresponding MGMT LED on the front panel. You need assign an IP address for the port to

manage the switch.

RJ-45 Console Port

Designed to connect with the serial port of a computer or terminal for monitoring and configuring

the switch. The switch has an RJ-45 console port and a micro-USB console port available.

Console input is active on only one console port at a time. By default, the micro-USB connector

takes precedence over the RJ-45 connector.

Power Supply Module 1/2

One AC Power Supply Module PSM150-AC has been installed in the switch. The malfunctioned

PSM150-AC can be replaced with a TP-Link power supply module of the same model. Its input

voltage is 100-240V~ 50/60Hz.

The AC Power Supply Module is fully hot swappable, helping to ensure no system interruption

during installation or replacement. For how to install/remove the Power Supply Module, please

refer to 3.3 Installing & Removing the Power Supply Module.

Caution: Please use the provided power cord.

With all the protective covers removed, the Interface Card (TX432 for example) and the AC Power

Supply Module PSM150-AC inserted, the rear panel of T3700G-52TQ is shown as the following figure.

Figure 1-3 Rear Panel (2)

Power

PS OK

Fault

PSM150-AC

100-240V~ 50/60Hz 2.5A

Power

PS OK

Fault

PSM150-AC

100-240V~ 50/60Hz 2.5A

SFP+

CLASS 1 LASER PRODUCT

TX432

JetStream Stackable L3 Managed Switch

05Preparing For Installation

Chapter 2 Preparing For Installation

2.1 Package Contents

Make sure that the package contains the following items. If any of the listed items is damaged or

missing, please contact your distributor.

One Power Cord, One Console

Cable and One USB Cable

One Switch This Installation Guide

Installation Guide

BusinessNetworking Solution

Two mounting brackets and the

ttings

One Resouce CD

2.2 Safety Precautions

To avoid any device damage and bodily injury caused by improper use, please observe the following

rules.

■Safety Precautions

■Keep the power off during the installation.

■Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good skin contact and

is well grounded.

■Use only the power cord provided with the switch.

■Make sure that the supply voltage matches the specifications indicated on the rear panel of the

switch.

■Ensure the vent hole is well ventilated and unblocked.

■Do not open or remove the cover of the switch.

■Before cleaning the device, cut off the power supply. Do not clean it by the waterish cloth, and never

use any other liquid cleaning method.

■Site Requirements

Temperature/Humidity

40℃

0℃

JetStream Stackable L3 Managed Switch

06 Preparing For Installation

Please keep a proper temperature and humidity in the equipment room. Too high/low humidity may

lead to bad insulation, electricity leakage, mechanical property changes and corrosions. Too high

temperature may accelerate aging of the insulation materials and can thus significantly shorten

the service life of the device. For normal temperature and humidity of the device, please check the

following table.

Environment Temperature Humidity

Operating 0℃to 40℃10% to 90%RH Non-condensing

Storage -40℃to 70℃5% to 90%RH Non-condensing

Clearness

The dust accumulated on the switch can be absorbed by static electricity and result in poor contact

of metal contact points. Some measures have been taken for the device to prevent static electricity,

but too strong static electricity can cause deadly damage to the electronic elements on the internal

circuit board. To avoid the effect of static electricity on the operation of the Switch, please attach

much importance to the following items:

■Dust the device regularly, and keep the indoor air clean.

■Keep the device well grounded and ensure static electricity has been transferred.

Electromagnetic Interference

Electronic elements including capacitance and inductance on the device can be affected by

external interferences, such as conducted emission by capacitance coupling, inductance coupling,

and impedance coupling. To decrease the interferences, please make sure to take the following

measures:

■Use the power supply that can effectively filter interference from the power grid.

■Keep the device far from high-frequency, strong-current devices, such as radio transmitting station.

■Use electromagnetic shielding when necessary.

Lightening Protection

Extremely high voltage currents can be produced instantly when lightning occurs and the air in the

electric discharge path can be instantly heated up to 20,000℃. As this instant current is strong

Otros manuales para JetStream T3700G-52TQ

Tabla de contenidos

Otros manuales de Cambiar de TP-Link

TP-Link

TP-Link JetStream TL-SG2008 Manual de usuario

TP-Link

TP-Link TL-SG105-M2 V2 Manual de usuario

TP-Link

TP-Link JetStream TL-SL5428E Manual de instrucciones

TP-Link

TP-Link TL-SL2452WEB - Web Smart Switch Manual de usuario

TP-Link

TP-Link JetStream TL-SL3428 Manual de instrucciones

TP-Link

TP-Link TL-RP108GE Manual de usuario

TP-Link

TP-Link TL-SL2218 Manual de usuario

TP-Link

TP-Link TL-SG105E Manual de usuario

TP-Link

TP-Link TL-SG105 Manual de usuario

TP-Link

TP-Link TL-SG105PP-M2 Manual de usuario

TP-Link

TP-Link TL-SG116E Manual de usuario

TP-Link

TP-Link JetStream TL-SG5428 Manual de usuario

TP-Link

TP-Link TL-SG1008 Manual de usuario

TP-Link

TP-Link JetStream TL-SG3424P Manual de instrucciones

TP-Link

TP-Link T3700G-28TQ Manual de instrucciones

TP-Link

TP-Link TL-SG1048 Manual de usuario

TP-Link

TP-Link Jetstream TL-SG2218 Manual de usuario

TP-Link

TP-Link JetStream T1500G-10MPS Manual de usuario

TP-Link

TP-Link TL-SG1005D - 5 PORT GIGABIT DESKTOP SWITCH Manual de usuario

TP-Link

TP-Link TL-SG1016D Manual de usuario

TP-Link

TP-Link TL-SG1008PE Manual de usuario

TP-Link

TP-Link JetStream TL-SG5412F Manual de usuario

TP-Link

TP-Link JetStream TL-SL5428E Manual de instrucciones

TP-Link

TP-Link TL-SG3210 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario