TP-Link TD-8610 Manual de usuario

Specifications are subject to change without notice. is a registered

trademark of TP-LINK Technologies Co., Ltd. Other brands and product names are

trademarks or registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to

make any derivative such as translation, transformation, or adaptation without permission

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CE Mark Warning

This is a Class B product. In a domestic environment, this product may cause radio

interference, in which case the user may be required to take adequate measures.

EC DECLARATION OF CONFORMITY (EUROPE)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this

product meets the requirements of the following standards:

• EN55022

• EN55024

• EN60950

SAFETY NOTICES

Caution: Do not use this product near water, for example, in a wet basement or near a

swimming pool.

Avoid using this product during an electrical storm. There may be a remote risk

of electric shock from lightning.

Package contents.............................................................................................................. 1

Chapter 1: Product Overview............................................................................................ 2

1.1 Product main specification................................................................................... 2

1.2 Supporting protocol.............................................................................................. 2

1.3 Transmit data-rate................................................................................................ 3

1.4 ATM property........................................................................................................ 3

1.5 System support.................................................................................................... 3

1.6 Working environment........................................................................................... 3

1.7 Electric parameter................................................................................................ 3

Chapter 2: Hardware Installation Guide............................................................................ 4

2.1 System requirement............................................................................................. 4

2.2 LED explanation................................................................................................... 4

2.3 Rear-panel........................................................................................................... 4

2.4 Hardware installation procedures（figure2-1）................................................... 5

Chapter 3: How to use ...................................................................................................... 6

3.1 Computer Configuration....................................................................................... 6

3.2 Login.................................................................................................................... 7

3.3 Setup ................................................................................................................... 8

3.4 Software Dial........................................................................................................ 9

Appendix A: Default Config............................................................................................. 10

Appendix B: Contact Information......................................................................................11

TD-8610 External ADSL MODEM User Guide

Package contents

The following contents should be found in your box:

 One TD-8610 ExternalADSL MODEM

 One AC power Adapter for TD-8610 ExternalADSL MODEM

 One Resource CD for TD-8610 ExternalADSL MODEM, including:

•This Guide

•Other Helpful Information

 One RJ45 cable

 Two RJ11 cable

 One ADSL splitter

Note: If any of the listed cable are damaged or missing, please contact the retailer from

whom you purchased the TD-8610 ExternalADSL MODEM for assistance.

- 1 -

TD-8610 External ADSL MODEM User Guide

Chapter 1: Product Overview

TP-LINK® TD-8610 External ADSL MODEM is the latest product designed and

manufactured by TP-LINK Technologies Co., Ltd. With TP-LINK’s excellent design of

circuit and high quality production, we guarantee ADSL MODEM a high performance,

very good stability and easy to use.

TD-8610 uses integrated ADSL2+ transceiver and a 256-MHz MIPS32 CPU.The AFE

supports full-rate ADSL connectivity conforming to the ITU and ANSI specifications;

MIPS32 CPU with MMU and 16-KB I-cache/8-KB D-cache is integrated into the device.

In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency

ADSL Framing (fast and interleaved) and the I.432 ATM Physical Layer.

TD-8610 is a complete plug-and-play solution. With standard Ethernet interface, it can

be directly connected to any 10M/100M Ethernet devices,support Auto-MDIX.

TD-8610 not only use html (web mode through Ethernet port) to configure the MODEM

but also use external utility software，too. You can download it from our website

(http://www.tp-link.com).

1.1 Product main specification

 High speed and asymmetry data transmit mode, adapt to wide-band internet access

 Point to point connection, provide safe and exclusive bandwidth

 Support All ADSL industrial standards

 Advanced DMT modulation and demodulation

 Firmware upgradeable

 Compatible with all mainstream DSLAM (CO)

 Real-time Configuration and device monitoring

 Quick response semi-conductive surge protect circuit, provides reliable ESD and

surge-protect function

1.2 Supporting protocol

- G.992.1 (G.dmt) - Annex A/B/C

- G.992.2 (G.lite) - Annex A/B/C

- ANSI T1.413

- G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant

- G.992.5 (ADSL2+) Annex A/B/C and Annex L (RE-DSL) compliant

- ADSL dual latency (fast path and interleaved path)

- I.432 ATM physical layer compliant

- 2 -

TD-8610 External ADSL MODEM User Guide

-Supports RFC2516 (PPPoE) *

- Supports RFC1483 (EoA)( Bridged)

NOTE. “*”Need third-party software.

1.3 Transmit data-rate

 Max download data-rate: 24Mbps

 Max upload data-rate: 1Mbps

 Max line length: 6Km

1.4 ATM property

 AAL0, AAL5, OAM, RM, and raw cell types supported

 Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs

supported in software

 Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)

1.5 System support

 Support PVC

 Support IEEE 802.3、IEEE 802.3u

 Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet

 Support Auto-MDIX

1.6 Working environment

 Operating temperature: 0℃~40 ℃

 Storage temperature: -40℃~70 ℃

 Humidity: 10%～90%

1.7 Electric parameter

 Adaptor power Output: 9VAC/0.8mA，50Hz or 60 Hz

 Power consumption: 4W Maximum

- 3 -

TD-8610 External ADSL MODEM User Guide

Chapter 2: Hardware Installation Guide

2.1 System requirement

Confirm your computer has been installed with networking interface card (NIC) before

connecting ADSL MODEM to your computer, with operating system supporting the

TCP/IP protocol.

2.2 LED explanation

The panel of ADSL MODEM includes one power button, one power indicator (RED) and

four function indicators (GREEN), and these five indicators are explained as chart 1-1:

Indicator Description Status Function Details

PWR Power On

Off Power OK

Power fail

ADSL ADSL status

Slow flash

Quick flash

Self-detecting when power up

Connecting to the telecom network

Connection to telecom network OK

ALARM Mistake On

Off

There is mistake when ADSL transmitting

data or receiving data

ADSL normal

ACT Data

Off

There is data transmitting or receiving on

WAN port

No data transmitting or receiving on WAN

port

LAN Ethernet

Off

Flash

LAN port normal

Connection on LAN port abnormal

Data transmitting or receiving on LAN port

Chart 1-1

2.3 Rear-panel

 ON/OFF: Turn on/off the ADSL MODEM’s power.

 Power (9VAC/0.8A input): please do not use any unknown power adaptor,

otherwise that may damage your ADSL MODEM.

 RESET(reset default): First press push the reset button of MODEM, then turn on

the MODEM’s power about three minuters. It will utilize the default manufacturer’s

setting.

 LAN: Connect with your computer’s NIC.

 LINE(WAN): Connect to the MODEM of Splitter or Connecting the telephone line.

- 4 -

TD-8610 External ADSL MODEM User Guide

2.4 Hardware installation procedures（figure2-1）

First Step: Connecting the MODEM of Splitter with the LINE port of the TD-8610 ADSL

MODEM by telephone line. While you need to use a telephone, please attach telephone

line into the phone of Splitter.

Second Step: Connect category 5 cable with RJ45 jacks toADSL MODEM’s LAN port

and your computer’s NIC.

Third Step: Link power adapter into the power jack of ADSL MODEM. Please note the

range of voltage of power adapter SHOULD be within AC 220～230V, 50Hz, which will

make the MODEM under normal operation.

Last Step: Check the line connection to see if everything is ready. Then power up.

（figure2-1）

- 5 -

TD-8610 External ADSL MODEM User Guide

Chapter 3: How to use

3.1 Computer Configuration

1. Connect the cable according to Chapter 2, turn on the power.

2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN

card in your PC, enter the IP address as 192.168.1.* (* is any value between 2 to

254, Netmask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value

provided by ISP).

Figure 3-1

Please note:

the users of Windows 98 can open TCP/IP Properties according to the following:

Right-press (Mouse) Network Neighbor -> Choose Properties -> Double-press TCP/IP..

PCI Fast Ethernet Adapter.

- 6 -

TD-8610 External ADSL MODEM User Guide

The users of Windows 2000/NT/XP can do the following: Right-press Network Neighbor

-> Choose Properties -> Right-press Local Connection -> Choose Properties ->

Double-press Internet Protocol (TCP/IP).

NOTE: The words in fact maybe are different with this guide.

Remarks: you can check whether your configuration is successful through PING

command. Enter Ping 192.168.1.1

If the screen likes the following, you succeed.

Pinging 192.168.1.1 with 32 bytes of data:

Reply from 192.168.1.1: bytes=32 time<10ms TTL-128

…

If the screen likes the following, you fail. Please try again.

Pinging 192.168.1.1 with 32 bytes of data:

Request timed out.

3.2 Login

Startup Internet Explorer, and enter 192.168.1.1; then enter user name(admin)、

password(admin); you will see the page (Figure 3-2). When ADSL connecting is OK, you

will see some information such as link rate and soon.

(Figure 3-2)

Default value of user name and password is admin; if you want to change them, please

- 7 -

Otros manuales para TD-8610

Tabla de contenidos

Otros manuales de Módem de TP-Link

TP-Link

TP-Link Archer T4U Manual de usuario

TP-Link

TP-Link TD-W8980 Guía del usuario

TP-Link

TP-Link Archer T2UB Nano Manual de usuario

TP-Link

TP-Link Archer VR600 Manual de usuario

TP-Link

TP-Link TD-8616 Manual de usuario

TP-Link

TP-Link W8951ND Manual de usuario

TP-Link

TP-Link TD-8816 Manual de usuario

TP-Link

TP-Link td-w8970 Manual de usuario

TP-Link

TP-Link TM-IP5600 Manual de usuario

TP-Link

TP-Link TD-VG3631 Manual de usuario

TP-Link

TP-Link TC7650 Manual de usuario

TP-Link

TP-Link TC-7610 Manual de usuario

TP-Link

TP-Link TC7650 Manual de usuario

TP-Link

TP-Link TD-W9960v Manual de usuario

TP-Link

TP-Link M7350 Manual de usuario

TP-Link

TP-Link TC-7610 Manual de usuario

TP-Link

TP-Link Archer T5E Manual de usuario

TP-Link

TP-Link TD-8610 Manual de usuario

TP-Link

TP-Link TD-W8968 Manual de usuario

TP-Link

TP-Link TL-WN821N Manual de usuario

TP-Link

TP-Link VX230v Manual de usuario

TP-Link

TP-Link TM-IA5629V Manual de usuario

TP-Link

TP-Link TD-8810 V5 Guía de inicio rápido

TP-Link

TP-Link TC-7610 Manual de usuario

Manuales populares de Módem de otras marcas

Davicom

Davicom DM562AP Manual de usuario

EpiValley

EpiValley TATA indicom SXC-1080 Manual de usuario

Zte

Zte WiMAX Manual de usuario

Intelimax

Intelimax MA-2060 Manual de usuario

SMC Networks

SMC Networks D3CM1604V Manual de uso y cuidado

Telstra

Telstra Wi-Fi 4G Advanced Pro X Manual de usuario

Thrane&Thrane

Thrane&Thrane imarsat EXPLORER 300 Manual de usuario

Samsung

Samsung AceLink SAM-335A Manual de usuario

Enfora

Enfora Enabler-G Guía de configuración rápida

iRZ

iRZ ATM2-232 Manual de usuario

Zhone

Zhone 6310 Manual de usuario

Paradyne

Paradyne Hotwire 7976 Manual de usuario

US Robotics

US Robotics 3453C Manual de usuario

MaxTech

MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario

Zte

Zte MF823 Manual de usuario

Four-Faith

Four-Faith F1403 Manual de usuario

Sierra Wireless

Sierra Wireless AIRLINK MP595W Manual de usuario

Gemtek

Gemtek WiMAX WIXFBR-103 Manual de usuario