Tourtecs IK2 Manual de usuario
INSTRUCTION MANUAL
IK2 / IK4
Motorcycle communication system
Table of contents
Introduction 4
Scope of delivery 4
Product overview 5
Explanation of buttons 5
Power on/off button 5
Intercom button 5
Volume + 6
Volume - 6
Explanation of the indicator lights 6
Installation methods 7
Permanent installation 7
Temporary installation 7
Installation of the main unit 7
Installation of microphone and speaker 7
Charging process 8
General operating instructions 9
Turning on and off 9
Connection with the Smartphone / GPS device 9
Automated connection to the smartphone 9
Phone calls 9
Accept phone calls 9
Reject phone calls 9
End phone calls 9
Voice dialing 9
Redial 10
Accepting calls from a third party 10
FM-Radio 10
Turning on and off 10
Change radio channel 10
Battery status query 10
Bluetooth communication system 11
Pairing with a Bluetooth headset 11
Connection and communication between two IK2 units 11
Connection setup between two IK2 units 11
Communication between two IK2 units 11
Connection and communication between IK4 units 12
Connection setup between two or more IK4 units 12
Communication between two IK4 units 12
2
Introduction
Thank you for choosing the IK2 / IK4 communication system. With its wireless design, the
communication system is designed for installation in most open face, flip-up or full-face
helmets.
With the IK2 / IK4, you can use your Bluetooth-enabled mobile phone to make hands-free
calls, listen to music or voice instructions from GPS navigation and activate the wireless
communication link from driver to driver or driver to passenger. It has a range of 1200
meters (depending on the environmental conditions).
The IK2 / IK4 complies with Bluetooth specification V3.0 and supports the following profiles:
● Headset Profile (HSP)
● Hands-Free Profile (HFP)
● Advanced Audio Distribution Profile (A2DP)
● Audio Video Remote Control Profile (AVRCP)
● Audio Gateway (AG)
Our helmet speakers achieve a good sound quality. The headset also offers a practical
combination of wind and ambient noise suppression for the microphone.
Please read this manual carefully before using this product.
Scope of delivery
Included in delivery:
● Main unit IK2 / IK4 communication system
● Speaker and microphone (headset)
● USB cable
● Mounting clamp console
4
Product overview
Explanation of buttons
Power on/off button
● Turning the unit on / off
● Pair with Smartphone
● Check battery status
● Ending calls via Bluetooth Intercom
● Play / pause music
● Accepting an initial call
● Accepting a second call
● Reject call
● End call
Intercom button
● Pairing a mobile telephone for Bluetooth intercom calls
● Accepting Bluetooth intercom calls
● Ending Bluetooth intercom calls
5
Volume +
● Increase volume
● Playing the previous piece of music
● Search for previous FM station
● Turning the radio on / off
● Redial
Volume -
● Decrease volume
● Playing the next piece of music
● Search for the next FM station
● Voice dialing
Explanation of the indicator lights
Description
Declaration
Blue light flashes once
No Bluetooth connection established
Blue and red light flash slowly alternately
Device ready for pairing
Blue light flashes quickly
Search for other Bluetooth devices
Blue and red light flash twice quickly and
simultaneously
Bluetooth bridge created
Blue and red light flash quickly and
simultaneously
Connection via Bluetooth is established
Blue light flashes twice
Pairing process completed
Blue light flashes quickly
Connected via Bluetooth
Red light flashes slowly
Charging in progress
Blue light is on
Charging completed
Red light flashes quickly
Low battery warning
6
Installation methods
Permanent installation
Step 1: Clean the left side of the helmet, near the lower edge.
Step 2: Remove the adhesive protection of the 3M sticker.
Step 3: Apply pressure to the metal clamp. Make sure that the clamp is securely
fixed.
Note: The 3M adhesive label requires 24 hours to dry.
Temporary installation
Step 1: Attach the clamp on the left side of the helmet, near the lower edge.
Step 2: After fixing the clamp, remove the metal handles.
Step 3: If necessary, use an additional rubber to prevent slipping.
Installation of the main unit
Step 1: Slide the main unit over the top edge of the bracket until you hear a click.
Step 2: Connect the headphones to the 3.5 mm headphone jack.
Installation of microphone and speaker
Step 1: Attach the speaker on the inside of the helmet in the ear area.
Step 2: Attach the microphone on the inside of the helmet, near the mouth.
7
Charging process
You can charge the communication unit with the USB cable that came with the unit. An
adapter for power connection is not included. The active charging process is indicated by the
red light. When charging is complete, the lamp turns off. We recommend charging the
battery fully before each use.
Charging the device takes about 3 hours and it should not be left unused for more than 6
weeks after charging, as this could damage the batteries.
The current charge level can be checked by double pressing the power on/off button and is
communicated via the speakers.
When the battery is low, a warning signal sounds every 5 minutes. In addition, the red
indicator light flashes rapidly three times.
8
General operating instructions
Turning on and off
To turn the unit on, press the on/off button for about 3 seconds until the blue light flashes
and the speaker announces "turned on".
To switch off the unit, press the on/off button for approx. 3 seconds in the activated mode
until the red lamp lights up and the speaker announces " Turned off".
Connection with the Smartphone / GPS device
Step 1: Press the power button in the on mode for about 8 seconds until the red and
blue light flashes alternately. The unit is now ready for pairing and the
speaker
announces "Pairing".
Step 2: Open the Bluetooth settings of your smartphone, search for and select the
"T9S-2 / T9S-4”.
Step 3: When the connection is established, the blue light of the device flashes twice.
Automated connection to the smartphone
If the connection between the device and a smartphone has been set up, it will be restored
automatically after the restart.
Phone calls
Accept phone calls
The unit will automatically answer incoming phone calls after about 12 seconds. Pressing
the on/off key accepts calls in advance.
Reject phone calls
Press the phone button within 5 seconds for about 2 seconds to reject incoming phone calls.
End phone calls
Press the on/off button twice in a row during the call to end the call.
Telephone calls that were answered via Bluetooth headset can be ended by pressing the
Intercom button.
Voice dialing
Press the volume button "-" twice while the phone is in standby mode to activate voice
dialing. The phone must support voice dialing.
9
Redial
Press the volume button "+" twice to redial.
Accepting calls from a third party
If an additional call is received while a call is active, it can be answered by pressing the
on/off key twice. The first call is now on hold. When the second call is finished, the first call
will be resumed.
FM-Radio
Turning on and off
Press one of the volume buttons for about 2 seconds while the radio is on to turn the radio
on or off.
Change radio channel
Press the volume key "+" twice to search for the previous radio channel.
Press the volume key "-" twice to search for the next radio channel.
Battery status query
The current charge status can be queried by double pressing the on/off button and is
announced via the speakers.
10
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Sistema de conferencias de otras marcas
Kramer
Kramer VIA GO Manual de usuario
AVT
AVT MAGIC AC1 Go Manual de usuario
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manual de usuario
Sony
Sony PCS-I150 Manual de usuario
Middle Atlantic Products
Middle Atlantic Products VTC Series Manual de usuario
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guía
