TourPro Lighting NOVA Manual de usuario

INTRODUCTION

Thank you for having chosen our LED lighting

Unpack the device, inside the box you should find:

The fixture device

One power cable

One XLR connection cable

This manual

Please check carefully that there is no damage caused by

transportation. Should there be any problems, consult your dealer and

don’t install this device.

DESCRIPTION

Features

Easy multi fixture hanging system, outdoor version available

4*100w 3000k LED, no ultraviolet radiation

More than 50,000 hours for the LED light source life

1300 lux in 5 meters

60 degree for beam angle

1/3/4/9 DMX channels

16 Bit Dimmer

DMX Mode /Master-slave mode

AC 100-240V 50/60Hz 400W

Diecasting heatsink, convection cooling, auto fans speed, no noise

With temperature sensor to extend the lamp life

7000 Hz LED scan rate

L: 373mm H:373mm W:193mm, Weight 9Kg

IP65/IP43 can be chosen

SAFETY INSTRUCTIONS

This device has left the factory in perfect condition. In order to

maintain this condition and to ensure a safe operation, it

is absolutely necessary for the user to follow the safety

instructions and warning notes written in this user manual.

This device falls under protection-class I. Therefore it is essential that

the device should be earthed.

The electric connection must carry out by qualified person.

If the external flexible cable or cord of this luminaire is damaged,

it shall be exclusively replaced by the manufacturer or his

service agent or a similar qualified person in order to avoid a hazard.

Make sure that the available voltage is not higher than stated at the

end of this manual.

Make sure the power cord is never crimped or damaged by sharp

edges.

If this would be the case, replacement of the cable must be done by

an authorized dealer.

Always disconnect from the mains, when the device is not in use or

before cleaning it. Only handle the power cord by the plug. Never

pull out the plug by tugging the power cord.

Never look directly into the light source, as

sensitive persons may suffer an epileptic shock.

Important:

Damages caused by the disregard of this user manual are not

subject to warranty. The dealer will not accept liability for any

resulting defects or problems.

DMX-512 control connection

The product has a DMX 512 input fitted with 3-pin XLR connectors.

Screened cables in compliance with EIA RS-485 specifications and the

following characteristics must be used for connections:

- 2 conductors plus screen

- 120Ohm impedance

- low capacitance

- max. transmission rate 250kBaud.

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is

in an electrically noisy environment,such as in a discotheque, it is

recommended to use a DMX terminator. This helps in preventing

corruption of the digital control signal by electrical noise. The DMX

terminator is simply an XLR plug with a 120 OHM resistor connected

between pins 2 and 3,which is then plugged into the output XLR

socket of the last fixture in the chain.

Display Menu

Main menu

Sub-menu

Value

Default

DMX Address

DMX Address Setting

1 - 512

Configure

Channel Mode

Channel 1Ch

Channel 9Ch

Channel 3Ch

Channel 4Ch

Channel 9Ch

Channel 10Ch

Keep Screen On

Disable

Enable

Keep Dmx Data

Disable

Enable

Fast Dimmer Mode

Enable

Disable

Information

Temperature

Temperature Of

Head 1 To Head

Auto Mode

Flowing Water

Light

Static Mode

Led Head 1

0 - 255

Led Head 2

0 - 255

Led Head 3

0 - 255

Led Head 4

0 - 255

Led Strobe

0 - 255

Main functions

1. Address:Current DMX address

A.Setting DMX address by button

Press ENTER button when show the address menu, then adjust

the DMX address by pressing [UP] or [DOWN] button.

Press [ENTER] to confirm or pressing [ESC] to return to main

menu.

B.Setting DMX address by controller

1.Set the DMX value of channel 5 to 10-15,channel 17 to 20-26,

channel 7 to 30-36,channel 8 to 40-46,then the devices

connected to the controller will enter to the setting address mode

2. Set the DMX value of channel 1 from 0-59,then you will see

the the first number of the Address change to (channel 1

vaule)/10.

For example,when set the value of channel 1 to 20,the first DMX

address number will be 2(20/10=2).

3. Set the DMX value of channel 2 from 0-99,then you will see

the the sencond number of the Address change to (channel 2

vaule)/10.

For example,when set the value of channel 2 to 30,the first DMX

address number will be 3(30/10=3).

4.Set the DMX value of channel 3 from 0-99,then you will see the

the third number of the Address change to (channel 3 vaule)/10.

For example,when set the value of channel 1 to 40,the first DMX

address number will be 4(40/10=4).

And the DMX address you set by conctroller will be 234.

5. Set the DMX value of channel 4 to 255,then you will save the

DMX address setted by the controller.

Caution: It won’t save the address if the address number is

over 512.

6. Set the value of channel 5-8 out of the value range show on the

step 1,and the device will exit the setting address mode.

2. Configure

Setting channel mode

Select the channel mode by pressing [UP] or [DOWN] button.

Keep screen on

Select the enable/disable by pressing [UP] or [DOWN] button.

Setting this to disable will close the screen automaticly as soon

as NO operation to keyboard in 45 seconds.

Setting this to enable will keep the screen on.

Keep DMX data

Select enable/disable by pressing [UP] or [DOWN] button.

Setting this to enable will set all DMX channel level to 0 as soon

as DMX signal lost.

Setting Fast mode

Select enable/disable by pressing [UP] or [DOWN] button.

Setting this to enable, the LEDs brightness will be set to

maximum or minimum immediate without delay effect as soon

as you change DMX level from the lowest to the highest or the

highest to the lowest in fast-speed.

3. Information

Temperature

Press [ENTER] button when show the Temperature menu, then

it will show the temperatures of 4 LED heads.

4. Auto Mode

Press [ENTER] button to enter Auto Mode menu, press [ENTER]

button to select the color mode, then select auto run mode by

pressing [UP] or [DOWN] button.

5. Static Mode

Press [ENTER] button to enter Static Mode, press [UP] or

[DOWN] button to select the Led head or strobe, then [ENTER] ,

adjust the value by pressing [UP] or [DOWN] button.

In this mode, DMX input is INVALID. Leds brightness and strobe

effect are controlled by this menu.

DMX functions and values

1CH Mode

No.

Function

Value

Description

Remark

Master Dimmer

000-255

0-100%

3CH Mode

No.

Function

Value

Description

Remark

Master dimmer

000-255

0-100%

Fine

master dimmer

000-255

0-100%

Strobe

000-015

Unused

range

016-240

Strobe

From slow to fast

241-255

Random

strobe

From fast to slow

4CH Mode

No.

Function

Value

Description

Remark

LED Head 1

000-255

0-100%

LED Head 2

000-255

0-100%

LED Head 3

000-255

0-100%

LED Head 4

000-255

0-100%

9CH Mode

No.

Function

Value

Description

Remark

Master Dimmer

000-255

0-100%

Fine

Master Dimmer

000-255

0-100%

Strobe

000-015

Unused range

016-255

Strobe

From slow to

fast

LED Head 1

000-255

0-100%

LED Head 2

000-255

0-100%

LED Head 3

000-255

0-100%

LED Head 4

000-255

0-100%

Macro

000-035

Unused range

036-071

Ramp up

From fast to

slow

072-107

Ramp down

108-143

Ramp up

and-down

144-179

Ramp up by

SIN curve

180-215

4-LED flow

216-255

Random LED

Dimmer Curve

0-63

Linear

64-127

Square

128-191

Invert Square

192-255

S-Surve

10CH Mode

No.

Function

Value

Description

Remark

Master Dimmer

000-255

0-100%

Fine

Master Dimmer

000-255

0-100%

Strobe

000-015

Unused range

016-255

Strobe

From slow to

fast

LED Head 1

000-255

0-100%

LED Head 2

000-255

0-100%

LED Head 3

000-255

0-100%

LED Head 4

000-255

0-100%

Auto Mode

000-035

Unused

range

From fast to

slow

036-071

Ramp up

072-107

Ramp down

108-143

Ramp up

and-down

144-179

Ramp up by

SIN curve

180-215

4-LED flow

216-255

Random LED

Dimmer Curve

0-63

Linear

64-127

Square

128-191

Invert Square

192-255

S-Curve

Dimmer Speed

0-254

Normal speed

From fast to

slow

255

Tungsten

effect

CLEANING AND MAINTENANCE

We recommend a frequent cleaning of the device. Please use a soft

lint-free and moistened cloth. Never use alcohol or solvents!

CAUTION!Disconnect from mains before starting

maintenance operation.

There are no servicable parts inside the device. Maintenance and

service operations are only to be carried out by authorized dealers.

If you need any spare parts, please use genuine parts.

If the power supply cable of this device becomes damaged, it has to

be replaced by authorized dealers only in order to avoid hazards.

If you have further questions, please contact your dealer.

INSTALLATION

The device must only be installed at a vibration-free, oscilation-free

and fire-resistant location.

Tabla de contenidos

Otros manuales de Equipo de DJ de TourPro Lighting

TourPro Lighting

TourPro Lighting MagicPar QZ-1915 Manual de usuario

TourPro Lighting

TourPro Lighting LIGHT SKY F1000 PROFILE-50R Series Manual de usuario

TourPro Lighting

TourPro Lighting ExtremeBeam 230 Manual de usuario

TourPro Lighting

TourPro Lighting LED Pin Spot Manual de usuario

TourPro Lighting

TourPro Lighting AQUABEAM SERIES Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario