TouchTunes Playdium Manual de usuario
Purpose
This document provides information about the Playdium Airflow Assembly Field-Replaceable Unit (TouchTunes p/n:
600208-001) and shows how to perform the replacement of the Airflow Assembly on a Playdium jukebox.
Topics
•Important Safety Information
•Included in This Kit
•Removing the Core
•Removing the Previous Airflow Assembly
•Replacing the Cable (Optional)
•Installing the Replacement Airflow Assembly
•Re-installing the Core
•Finishing Up
•Contacting TouchTunes Technical Support
A
udience
• TouchTunes Playdium Jukebox Operators
• TouchTunes field service and customer support
Estimated Time
15 minutes
Required Personnel
1 Technician
This document includes the following task types:
Software
Electrical
Mechanical
Packaging
PLAYDIUM Airflow Assembly FRU
Installation Guide
April 2014
900874-001
Rev 00
2 Playdium Airflow Assembly FRU Installation Guide
Important Safety Information
Important Safety Information
Included in This Kit
Ensure that you have received all the required parts before proceeding with this installation.
Part Amount TouchTunes Part #
Airflow Assembly Bracket 1 401370-001
Airflow Assembly Cable 1 300923-001
This document 1 900874-001
WARNING: When performing this procedure or any other maintenance on your jukebox, the unit must be
powered off.
To be installed by experienced service personnel only, familiar with the product.
WARNING: Risk of Fire or Electric Shock. Installation of Airflow Assembly requires knowledge of this product.
If not qualified, do not attempt installation.
To prevent damage including abrasion, the wiring harness shall be routed and securely held to along the outer
enclosure.
3Playdium Airflow Assembly FRU Installation Guide
Removing the Core
Removing the Core
1. Unlock the payment panel and open it to reach the lever below the core.
2. Set the power rocker switch on the Playdium’s power strip to OFF.
3. Pull the pin that keeps the lever from moving (A). Then, while still pulling on the pin, pull the lever down (B) to pop the
core out of its connectors (C).
Key
A
C
B
4 Playdium Airflow Assembly FRU Installation Guide
Removing the Previous Airflow Assembly
4. Lift the core, and carefully set it face down on a horizontal, flat surface (such as a table or a counter) covered by a soft
cloth or similar, to avoid scratching or otherwise damaging the touch screen glass.
Removing the Previous Airflow Assembly
1. To remove the malfunctioning Airflow Assembly, you must first unfasten it and pull it out of place. The airflow assembly
is fastened using two screws that go through the top air vents.
2. With the screws removed, the airflow assembly can be pulled out by first lifting the back, then pulling the bracket
forward.
5Playdium Airflow Assembly FRU Installation Guide
Replacing the Cable (Optional)
3. Disconnect the cable from the Airflow Assembly.
Replacing the Cable (Optional)
Check the cable that connects the Airflow Assembly to the Backplane, and ensure it is not damaged. If the cable is damaged,
you can replace it using the cable provided with your Airflow Assembly FRU kit.
1. The cable is connected to the Backplane in two places. Disconnect the cable from these two places, and set it aside.
2. Connect the replacement cable in the same two places. The narrower connector, at the end of the cable, connects to
“EXT. LIGHT 3”, while the wider connector goes into “OPTION 2”. Use the following schematic to help you to connect to
the correct sockets on the backplane:
Note: The cable is labeled at each connector to help with figuring out where it connects.
3. Connect the other end of the cable to the single connector on the Airflow Assembly.
LAN
USB
12 3
4
USB
5
PAYMENT
LIGHT
DOOR
SWITCH
COIN
ACC
BILL
ACC
SERIAL
1
EXT. LIGHT
12 3
AUDIO IN
2 1 3
AUDIO OUT
MIC 1 AUX
SPK
2
3
&
4
1
&
2
RF REMOTE
ART900777-001R04
LEFT TOP
SIDE LIGHT
VOLUME PCB OPTION 2
RIGHT
SIDE LIGHT
OPTION 2
ID MODULE
MNGR
R
-+
L
+-
ZONE
2
SPEAKERS
R
-+
L
+-
ZONE
1
CLASS 2 WIRING
CLASS 2 WIRING
To Airflow Assembly
6 Playdium Airflow Assembly FRU Installation Guide
Installing the Replacement Airflow Assembly
Installing the Replacement Airflow Assembly
1. Move the airflow assembly into position.
2. Hook up the top-left tab first (A), then the top-right (B).
3. Hook up the back tabs, until the assembly snaps into place (C).
4. Fasten the airflow assembly using the two screws you removed earlier.
5. The middle part of the airflow assembly, where the electronics are, and where the cable connects, must hang
downwards, and move freely. Check that this part is not stuck or immobilized.
6. There is a velcro strip in the back of the assembly. Check that it’s wrapped around the back of the assembly, and that it
does not impede the movement of the moving flap, or get in the way of the fans.
AB
C
7Playdium Airflow Assembly FRU Installation Guide
Re-installing the Core
Re-installing the Core
Note: Playdium MUST be mounted vertically when docking the core. Do not attempt to dock the core while the chassis is
not mounted vertically. Failure to do so could damage the core or the chassis.
1. Ensure that the red lever on the chassis is pulled down and vertical, ready to receive the core.
2. Lift the core, and position on the chassis, above the red lever.
8 Playdium Airflow Assembly FRU Installation Guide
Finishing Up
3. While holding the core in the chassis, pull the pin that holds the red lever in position, and then carefully move the red
lever up.
Note: You must hold the core to prevent it from dropping suddenly when the pin is pulled, otherwise the core can fall
suddenly onto the fingers that are pulling the pin.
4. Once you’ve moved the lever enough, the pin will stay up. Release it, and use that hand to push the core into the chassis,
while pushing the red lever up.
5. As you push the red lever up, the core will go down. When the red lever reaches horizontal, the core will be in its final
position, and the pin will snap into place.
Finishing Up
1. Set the power rocker switch on the Playdium’s power strip to ON.
2. As Playdium powers up, check that the fans in the Airflow Assembly spin up and are pushing air out the top of the
jukebox, using your hand to feel for the air flow. After a moment, the fans will slow down or turn off, adapting to the airflow
needs of the jukebox’s internal components.
3. Close the payment panel by gently pulling it up and shut, then pressing on its front face to engage the locking
mechanism.
4. Secure the payment panel by using the key to lock its case.
Copyright © 2014 TouchTunes Interactive Networks
TouchTunes Interactive Networks, Inc.
400 Sainte Croix Avenue, Suite 200 E
Montreal, Quebec,
Canada, H4N 3L4
TouchTunes Interactive Networks, Inc.
850 Third Ave, Suite 15C
New York, NY 10022
USA
Technical Support
847-353-1954
www.touchtunes.com
9Playdium Airflow Assembly FRU Installation Guide
Contacting TouchTunes Technical Support
Contacting TouchTunes Technical Support
If you need help with or have questions about this document, contact TouchTunes by:
•using the e-mail links on the Contacts page on the TouchTunes Dashboard at
https://operator.touchtunes.com
•calling TouchTunes 24/7 Service Hotline at 847-353-1954
To help us assist you more effectively with problem reports, this information may be required when contacting TouchTunes
Support:
•Jukebox model, such as Playdium, Virtuo, Allegro MX-1, Ovation
•Jukebox ID
•the serial number of any component you believe to be defective
•the date/time of the problem
•actions performed immediately before the problem occurred
•any additional comments
Otros manuales para Playdium
3
Tabla de contenidos
Otros manuales de Tocadiscos tragamonedas de TouchTunes
TouchTunes
TouchTunes Ovation Jukebox Manual de usuario
TouchTunes
TouchTunes Ovation Manual de usuario
TouchTunes
TouchTunes Allegro MX-1v Instrucciones de montaje
TouchTunes
TouchTunes Virtuo 700259-001 Instrucciones de montaje
TouchTunes
TouchTunes Virtuo Test Fixture Manual de usuario
TouchTunes
TouchTunes Virtuo II Series Manual de usuario
TouchTunes
TouchTunes Allegro Suplemento
TouchTunes
TouchTunes Playdium Manual de usuario
TouchTunes
TouchTunes Maestro II Manual de usuario
TouchTunes
TouchTunes ANGELINA Manual de usuario
TouchTunes
TouchTunes Photobooth Manual de usuario
TouchTunes
TouchTunes Allegro MX-1 Guía de inicio rápido
TouchTunes
TouchTunes Playdium Instrucciones de montaje
TouchTunes
TouchTunes Playdium Manual de usuario
TouchTunes
TouchTunes Virtuo Floor Stand Manual de usuario
TouchTunes
TouchTunes Playdium Floor Stand Instrucciones de montaje
TouchTunes
TouchTunes ANGELINA Instrucciones de montaje
