Toshiba STRATA CIX-CTX-QRG-VB VERSION B1 Manual de usuario

STRATA

CIX/CTX Helping You

Communicate Better

Business Telephones

DKT / IPT Telephone

Quick Reference Guide

2Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05

Introduction

This quick reference guide applies to Toshiba DKT3200-series digital

telephones and Internet Protocol (IPT1020-SD, IPT2000-series and

SoftIPT) telephones connected to a Strata CIX/CTX system.

See your Telephone System Administrator to find out which features

you have. Use the check boxes or blank lines to enter the variable

selections for your telephone.

What’s My Line?

Throughout this guide, the word “line” is mentioned. Check mark

which Line type you have. For example, you will be instructed to

“select a line.” “Line” can be:

pLine button

pPooled Line Group

pGroup Line button

pLine out requiring an access code – where you enter an outside

line or line group access code (e.g., dial 9).

Which Outgoing/Incoming Call Features Do I Have?

Check mark here which outgoing/incoming feature you have on your

system. Then go through the rest of this guide and check mark that

feature where it’s noted.

pAutomatic Line Selection (ALS): For outgoing calls: You

have ALS if you hear dial tone and the Line LED lights steady

green when you lift the handset or press Spkr.

pRinging Line Preference: You answer an incoming Line ringing

your station by lifting the handset or pressing Spkr.

pTone Signaling: Internal incoming call: you hear successive

ring tones, then lift the handset or press Spkr.

pVoice First Signaling: Internal incoming call: your phone does

not ring; instead you hear a long tone, then the caller’s voice. Talk

in the direction of your phone, or answer the call as you normally

would by lifting the handset or pressing Spkr.

Note You can change between Tone and Voice Signaling

on a call-by-call basis by pressing 1after dialing an

internal telephone number.

pHot Dialing: If your telephone is programmed for “hot dialing,”

you do not have to press Spkr or lift the handset before dialing

internal or external speakerphone calls. When you dial a number,

the speakerphone automatically turns on and the Spkr and Mic

LEDs light up.

Answering a Call

!Lift the handset or press Spkr.

pIf you don’t have Ringing Line Preference: press the flashing line

or extension button and lift the handset.

Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05 3

Which Codes Do I Use?

Default feature codes are listed in this guide. Check with your System

Administrator to see if these codes have been changed. If so, write the

new codes in the blank lines and cross out the default codes. For

example:

Cnf/Trn + #46 or .

Making a Call

Hot Dialing

1. To make a call using Hot Dialing, dial the number.

2. When connected, you can continue speakerphone operation or

lift the handset and continue the conversation.

Spkr Button

1. To make a call, press Spkr.

2. Dial the number.

3. When connected, you can continue to use the speakerphone or

lift the handset and continue the conversation.

Handset

1. To make a call, lift the handset, then dial the number.

2. When connected, you can continue to use the handset or switch

to speakerphone by holding down Spkr and replacing the

handset.

Dial Directory

1. Press SK1 or Mode from your telephone (shown right). The

Select Directory menu appears.

Note The soft keys on the

Select Directory are:

My = Personal SD Names

EXTR= Sys. SD Names

INTR = Directory No. Names

Dial = Cancel directory, get

dial tone.

2. Press the appropriate soft key

and use the dial pad to enter the first character of the name

...or if you do not select a directory, you can go directly to the

dial pad and enter a character. This makes names from all

directories available.

3. Press Find soft key to start the Dial-directory search.

4. Press Next soft key to go through the directory until you see

the name.

5. Press Call soft key to call.

6. Press Back soft key to go back through the directory.

4Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05

Handsfree Answerback

!To receive a hands free internal call over the speakerphone

1. You hear a single long tone, then the caller’s voice. Do not lift

the handset; speak toward the telephone in a normal voice.

2. Press Spkr or take the handset off-hook if you wish to

transfer the call or place it on hold.

!To switch between Handset and Speakerphone

!Press Spkr and place the handset on-hook to switch from

Handset to Speakerphone mode.

Account Code Calls

!To dial with a Forced Account Code (FAC)

1. Place a call in the normal method.

2. After the tone burst, enter the Account Code.

If the code is invalid, you hear re-order tone and the call is

rejected.

!To use an Emergency Override of an FAC

You can bypass Forced Account Code requirements with three

emergency numbers, including 911. See your System

Administrator for these numbers: ____________

!To dial with Voluntary Account Codes

1. After accessing a CO line, press Account Code

...or Cnf/Trn + #46 ________.

You can enter it at any time during a call.

2. Enter the Account Code.

You should hear confirmation tone if the code is valid or two

short tones if it is invalid.

3. Dial a telephone number if you entered the code after

accessing an outside line or resume talking or hang up if you

entered the code after the call.

Call Transfer

1. While on a call, press Cnf/Trn.

2. Dial the extension and announce the call or “blind transfer”

(hang up).

During call transfer, you can reconnect to the original caller by

pressing your flashing extension button.

3. Camp on to a busy station: If the station is busy, hang up. The

called station receives a tone. Once the busy line is free, the

transferred line is called back.

Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05 5

Conference Calls

1. While on a call, press Cnf/Trn.

2. Call another station or outside line.

3. When the called party answers, press Cnf/Trn. If it’s busy or

there’s no answer, press Cnf/Trn again to return to the

original connection. All parties are conferenced.

4. Repeat the above steps to add more lines. You can conference

up to eight parties.

Note When the person who initiates the conference

(master) hangs up, control transfers to the first internal

station added to the conference. If no internal stations are in

the conference, the call disconnects.

!To transfer conference control

1. Do steps 1 and 2 above to add the line to which you wish to

transfer conference control.

2. Announce the call and hang up to transfer the call. This station

is now the conference “master” with the ability to add or delete

parties.

!To hold a conference call

!If you are the “master” conference controller, press Hold once

(or twice for Executive Hold) to place the conference call on

hold.

The conference continues and you can join at any time without

giving up “master” abilities. Music-on-hold is suppressed in

this mode.

!To delete the last member added to a conference

!While a call is in progress, press the Cancel button.

!To conference two outside Lines

1. While talking on an outside call, press Cnf/Trn.

2. Access an outside line.

3. After the party answers, press Cnf/Trn.

4. If you receive a busy tone or if the station does not answer,

press the flashing button to return to the original call.

5. Press Cnf/Trn and hang-up.

Note Most phone companies provide auto disconnect, but

if it is not provided, the lines must be supervised to

disconnect.

6. To supervise a tandem call, press the extension button. If the

parties have finished, hang up or if the parties are still talking,

press Cnf/Trn and hang-up.

6Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05

Hold

1. To place a call on Hold, press the Hold button.

2. To return to the held call, press the held line’s button.

If you do not return to the held call, it rings back to your phone.

If you are busy on another call, you hear two tone bursts. If the

held party hangs up, the call is released.

3. If you have additional lines at your station to hold, repeat Step

1 above.

!To place a call on Exclusive Hold

!While on a call, press Hold twice. (No one can accidently

pick up your call.)

!To place a call on Automatic Hold

!While on a call, press another extension button to receive/

originate a new call. You can switch between calls without

having to press Hold.

Make sure this feature is programmed on your system; if not,

existing calls will drop.

!To place a call on Consultation Hold

If you have multiple extensions on your phone, you can hold a

different call on each extension.

!Press Cnf/Trn.

Call Forward - Any Calls (Internal & External)

There are two ways to perform each Call Forward:

!Enter the button sequence below

All Calls: Press Ext. + #6011 or ________ + Destination No.

Busy: Press Ext. + #6021 or ________ + Dest. No.

No Answer: Press Ext. + #6031 or ________ + Dest. No. +

Timer (seconds, 2-digits) + #

Busy No Answer: Press Ext. + #6041 or ________ + Dest.

No. + Timer (seconds, 2-digits) + #

Cancel: Press Ext. + #6051 or ________

!...or program a flexible button to perform the sequence

See “Flexible Buttons” for instructions.

Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05 7

Call Park Orbits

!To park a call

1. While on a call, press Park in Orbit

...or Cnf/Trn + #33 or ________ .

2. Specify the Park Orbit using one of the following:

•Press *and the system automatically selects a General

Park Orbit between 7000~7019. The chosen orbit

appears on the LCD.

•Enter a valid extension.

•Press #and the system automatically selects your

extension as the orbit.

3. Hang up. If the parked call is not retrieved, the call rings back

to your phone.

!To retrieve a parked call

1. Press Park in Orbit

...or your extension button + #32 or ________ .

2. Enter the Orbit Number where the call is parked.

Call Pickup

1. Press an extension button.

2. Enter a code from the following list:

Group Pickup: #5#34 or ________

Directed Terminal Pickup: #5#5 or ________

Other (see System Administrator):_________

3. Dial the extension that is holding the ringing or held call to be

picked up.

Echo Cancel

!If you experience echo while conversing on your IP telephone,

tap Vol "or #once to cancel the echo sound.

Paging

!To make a page announcement to a phone or external

speakers

1. Press extension, lift the handset, and enter:

#30 or ________ (all groups)

..or #31 or ________ + _____ the Group page access code.

See “Flexible Buttons” for more paging codes.

2. Make your announcement, then hang up.

!To make an All Call Page

1. With the handset off-hook, press All Call Page

...or extension + #30. This pages all phones in the All Call

Page Group, and may page external speakers (depends on

programming).

2. Make your announcement then hang up.

8Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05

Redial

Use this button to redial the last number dialed from your phone.

!To redial the last number, press Redial or *0.

Speed Dial

!To store a Station Speed Dial Number

We suggest storing Speed Dial numbers on a One Touch button;

use Speed Dial Codes to store more numbers.

1. Press Program or dial #9876.

2. Press Spdial.

3. Press 1, then enter a Speed Dial Code (00~99).

4. Enter the number to be stored in the Speed Dial bin (32 digits

max.).

5. Press Spdial to store the entry. See “DATA

PROGRAMMED.”

6. Lift and replace the handset.

!To clear a number from a Station Speed Dial code

!Repeat the previous procedure skipping Step 4.

!To make a call using Speed Dial

1. Lift the handset.

2. Access a outside line (if necessary).

3. Press Spdial. Then dial the Station or System Speed Dial

Number.

One Touch Buttons

This feature is useful for storing frequently dialed numbers.

!To change a One Touch Button

1. Press #9876 to enter User Programming Mode.

2. Press the One Touch button to set.

3. Enter the digits or special buttons to be stored.

4. Press the One Touch button to save the entry.

If these steps do not work, you may have to create a One Touch

button (see “Flexible Buttons” ).

!To Use a One Touch Button, just press it.

Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05 9

Voice Mail Call Monitor

System Availability: Only with Strata CTX28

!To enable and disable Voice Mail Call Monitor

1. Press Call Monitor button.

2. Enter your voice mail password, then press #.

!To cancel Call Monitor

!Press Call Monitor button.

!To monitor a call using Call Monitor

1. The flashing Call Monitor button indicates that a message is

being recorded in voice mail.

2. To listen, press the Call Monitor button.

3. To talk to the caller, press the Call Monitor button again.

Voice Mail - Direct Transfer

1. While on a call, press Cnf/Trn.

2. Press #407 ____.

3. Enter the voice mailbox number (may be the same as the

extension number), then press #.

4. Hang up (the caller is connected to the voice mailbox) or press

Cnf/Trn to return to the calling party.

Volume Control

!To adjust handset volume

!During a call, press down Vol "or #. When you hang up,

volume returns to default.

!To adjust the speaker volume for internal/external calls and

background music

!Press Spkr. Select a line and press Vol "or #.

!To adjust Ring Tone, Handsfree Answerback and Speaker

Off-hook Call Announce

!With an idle phone and handset on-hook, press Vol "or #.

When you hang up, volume returns to default.

10 Strata CIX/CTX DKT/IPT Telephone Quick Reference Guide 11/05

IPT2008-SDL / DKT3014/3214-SDL LCD Features

!To use Direct Station Selection

1. Press the DIRECT SS Soft Key to view the first screen.

2. Press the soft keys MORE or PREVIOUS to view the other

pages.

3. To select someone from the list, press the Soft Key next to the

name.

!To use Speed Dial

1. Press the Soft Key next to the SYSTEM SD or

PERSONAL SD to view the first screen.

2. Press the soft keys MORE or PREVIOUS to view the other

pages.

3. Select someone from the list by pressing the Soft Key next to

the name.

!To use Directory Menu

1. Press the EXTERNAL DIR or INTERNAL DIR to view the

first screen. The directory list displays.

2. Press the soft keys MORE or PREVIOUS to view the other

pages.

3. Select someone from the list by pressing the Soft Key next to

the name.

Flexible Buttons

There are 10, 14 or 20 Flexible Buttons on your telephone. You can

program features onto Flexible Buttons for easy access.

1. Press #9876 to enter User Programming Mode.

2. Press Hold.

3. Press the Flexible Button to set or change.

4. Enter the Flexible Button Code (see following list).

5. Press the same Flexible Button (flashing). “DATA

PROGRAMMED” appears on your LCD.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Teléfono de Toshiba

Toshiba

Toshiba Strata AirLink DK280 Manual de usuario

Toshiba

Toshiba Strata IP5000 series Manual de usuario

Toshiba

Toshiba CIX Manual de usuario

Toshiba

Toshiba Strata DK14 Manual de usuario

Toshiba

Toshiba STRATA CIX Manual de usuario

Toshiba

Toshiba Strata DK Backup Manual de instalación y operación

Toshiba

Toshiba Strata DK Backup Manual de usuario

Toshiba

Toshiba Strata DK Backup Manual de instrucciones

Toshiba

Toshiba Strata DK 24 Manual de usuario

Toshiba

Toshiba Strata DK 2000 Series Manual de usuario

Toshiba

Toshiba Strata CTX DKT3000 Series Guía de configuración

Toshiba

Toshiba Perception II Manual de usuario

Toshiba

Toshiba Strata DK14 Manual de usuario

Toshiba

Toshiba Strata CTX 100-S Manual del propietario

Toshiba

Toshiba Strata DK Backup Manual de usuario

Toshiba

Toshiba Strata DK 24 Manual de usuario

Toshiba

Toshiba Strata CT Manual de usuario

Toshiba

Toshiba Strata CIX DP-5000 series Manual de usuario

Toshiba

Toshiba 2000 Manual de usuario

Toshiba

Toshiba Strata CIX DP-5000 series Manual de usuario

Toshiba

Toshiba PERCEPTION 4000 Manual de usuario

Toshiba

Toshiba Strata CIX DP5000-Series Manual de usuario

Toshiba

Toshiba Strata DK8 Manual de usuario

Toshiba

Toshiba CIX Manual de usuario

Manuales populares de Teléfono de otras marcas

GE 2-9480 Manual de usuario

Geemarc

Geemarc PHOTOPHONE 155 Manual de usuario

D-Link

D-Link DWR-720/PW Manual de usuario

Interquartz

Interquartz Gemini IQ333 Manual de usuario

SSS Siedle

SSS Siedle HT 840-0 Manual de usuario

Motorola

Motorola TITANIUM Manual de usuario

Panasonic

Panasonic ICX Manual de usuario

LG H870DS Manual de usuario

Samsung

Samsung GT-I9500 Manual de usuario

AT&T

AT&T Trimline 205 Manual de usuario

Selta

Selta zenyth 600 Manual de usuario

Doro

Doro AFTI 20 Manual de usuario

UNIQCELL

UNIQCELL A1 Manual de usuario

Panasonic

Panasonic KX Series Manual de usuario

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manual de usuario

BT Decor 425 Manual de usuario

NEC

NEC SV8500 Manual de usuario

Teledex

Teledex PEARL Manual de usuario