Toshiba MK8009GAH Guía de inicio rápido

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

TOSHIBA STORAGE DEVICE DIVISION

MK4009GAL & MK8009GAH

HDD INSTALLATION NOTES

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s MK4009GAL (HDD1622) and MK8009GAH (HDD1584) hard disk drives

are a series of ultra-slim fast light weight 1.8 inch Winchester disk drive. The drives are

ATA-6 compliant.

SPECIFICATIONS MK4009GAL MK8009GAH

HDD1622 HDD1584

FORMATTED CAPACITY 40.0GB 80.0GB

HEIGHT 5mm 8mm

WEIGHT 1.69oz (48g) 2.08oz (59g)

NO. OF DISKS (PLATTERS) 1 2

NO. OF DATA HEADS 2 4

FUNCTIONAL SPECIFICATION

LOGICAL DRIVE MK4009GAL MK8009GAH

PARAMETERS HDD1622 HDD1584

NO. OF CYLINDERS (user) 62,640 62,640

BYTES PER SECTOR 512 512

BUFFER SIZE 8MB 2/8MB

ROTATION SPEED (±0.1%) 4,200rpm

TRANSFER RATE INTERNAL 165.0 - 356.8 Mbits/sec.

NO. OF CYLINDERS (logical) 16,383

NO. OF HEADS (logical) 1 6

NO. OF SECTORS/TRACK 6 3

HOST TRANSFER RATE

PIO/ULTRA DMA (ATA mode) 16.6/100MB/s

SEEK TIME

AVERAGE 15ms

TRACK-TO-TRACK 3ms

MAXIMUM 26ms

TEMPERATURE

OPERATING 41°F - 140°F (5°C - 60°C)

NON-OPERATING -4°F - 149°F (-20°C - 65°C)

HUMIDITY

OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)

SHIPPING 5 - 90% R.H. (No condensation)

WET BULB 29°C(operating)/40°C(non-operating)

CONNECTOR CABLING INFORMATION

The following table describes all of the pins on the Task File Interface:

PIN SIGNALS PIN SIGNALS

1 RESERVED 2 RESERVED

3 - RESET 4 GROUND

5 DD7 6 DD8

7 DD6 8 DD9

9 DD5 10 DD10

11 DD4 12 DD11

13 DD3 14 DD12

15 DD2 16 DD13

17 DD1 18 DD14

19 DD0 20 DD15

21 GROUND 22 DMARQ

23 GROUND 24 - DI0W

STOP

25 -DIOR 26 GROUND

-HDMARDY

HSTROBE

27 IORDY 28 GROUND

-DMARDY

DSTROBE

29 DMACK 30 INTRQ

31 DA1 32 - PDIAG/-CBLID

33 DA0 34 DA2

35 -CS0 36 -CS1

3 7 - DASP 3 8 +3.3V

39 +3.3V 40 RESERVED

Note: “-“ in front of signal name indicates negative logic.

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). Prior to opening the anti-static bag, it is recommended that the user ground

himself with a ground strap or by touching the PC chassis or other metal object. Re-

move the drive from the anti-static bag and check it for damage. Save the shipping

container and packing material for possible use later.

HANDLING AND MOUNTING CONSIDERATIONS

•Installation and mounting of these drives is specific to the application environment.

•Handle drive only by the edges. When handling or mounting, take care not to apply

any pressure to the top cover.

•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a

small distance onto a tabletop or other hard surface can damage drive. When

mounting the drive, do so in such a fashion that the drive will be isolated from

excessive shock.

•Do not mount in an environment where the temperature of the drive’s top cover will

exceed 65°C. (During operation, the temperature of the top cover can rise 15°C

above ambient).

•Do not disassemble, modify or repair drive.

•A rattle heard when the drive is moved is normal and not a sign of failure.

INTERFACE CONNECTOR

Drive Side Connector DDK Ltd, FF19A-40B-R11b

Recommended host side FPC 1. Width: 20.50 ±0.07mm

2. Thickness: 0.20 ±0.03mm

3. Length: 90mm (max)

4. Impedance: Typical 50ohm

5. Plating: Gold over Nickel plating (note 1)

6. Adhesive: Heat-hardened adhesive

Connector Durability (note 2) 20 times

FPC Holding fource (note 3) Typ: 17[N] Min: 5[N]

* Do not pull out FPC with the connector locked.

* Do not lock without FPC

Notes:

1. To avoid Sn whisker

2. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC

3. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC after pulling out repeatedly

FIGURE 1 – INTERFACE CONNECTOR

DEVELOPER SUPPORT

Toshiba Storage Device Division (SDD) the industry pioneer in small form factor

storage supports developers who are looking for small form factor HDD’s that deliver

the unbeatable combination of high-performance and high-capacity storage. Toshiba

HDD’s can be found “under the hood” of some of today’s hottest portable products. If

you are interested in discussing your product application with us please contact us.

E-mail: [email protected]

Phone: (949) 462-7502

Fax: (949) 588-7845

Web: http://developer.toshiba.com

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

UNPACKING PROCEDURE

Visually inspect the shipping container prior to unpacking for any signs of damage to

the container or its contents (the carrier is responsible for any damage incurred during

shipment). Prior to opening the anti-static bag, it is recommended that the user ground

himself with a ground strap or by touching the PC chassis or other metal object. Re-

move the drive from the anti-static bag and check it for damage. Save the shipping

container and packing material for possible use later.

HANDLING AND MOUNTING CONSIDERATIONS

•Installation and mounting of these drives is specific to the application environment.

•Handle drive only by the edges. When handling or mounting, take care not to apply

any pressure to the top cover.

•Avoid subjecting the drive to excessive shock. Do not drop the drive, even a

small distance onto a tabletop or other hard surface can damage drive. When

mounting the drive, do so in such a fashion that the drive will be isolated from

excessive shock.

•Do not mount in an environment where the temperature of the drive’s top cover will

exceed 65°C. (During operation, the temperature of the top cover can rise 15°C

above ambient).

•Do not disassemble, modify or repair drive.

•A rattle heard when the drive is moved is normal and not a sign of failure.

INTERFACE CONNECTOR

Drive Side Connector DDK Ltd, FF19A-40B-R11b

Recommended host side FPC 1. Width: 20.50 ±0.07mm

2. Thickness: 0.20 ±0.03mm

3. Length: 90mm (max)

4. Impedance: Typical 50ohm

5. Plating: Gold over Nickel plating (note 1)

6. Adhesive: Heat-hardened adhesive

Connector Durability (note 2) 20 times

FPC Holding fource (note 3) Typ: 17[N] Min: 5[N]

* Do not pull out FPC with the connector locked.

* Do not lock without FPC

Notes:

1. To avoid Sn whisker

2. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC

3. In horizontal direction with FPC of 0.20mm in thickness and with the same

connector and FPC after pulling out repeatedly

FIGURE 1 – INTERFACE CONNECTOR

DEVELOPER SUPPORT

Toshiba Storage Device Division (SDD) the industry pioneer in small form factor

storage supports developers who are looking for small form factor HDD’s that deliver

the unbeatable combination of high-performance and high-capacity storage. Toshiba

HDD’s can be found “under the hood” of some of today’s hottest portable products. If

you are interested in discussing your product application with us please contact us.

E-mail: [email protected]

Phone: (949) 462-7502

Fax: (949) 588-7845

Web: http://developer.toshiba.com

MK4009GAL/MK8009GAH P/N 480077-A0 P/N 480077-A0 MK4009GAL/MK8009GAH

Hard Disk Drive Installation Notes 07/06 07/06 Hard Disk Drive Installation Notes

TOSHIBA STORAGE DEVICE DIVISION

MK4009GAL & MK8009GAH

HDD INSTALLATION NOTES

Contents subject to change without prior notice.

GENERAL DESCRIPTION

Toshiba’s MK4009GAL (HDD1622) and MK8009GAH (HDD1584) hard disk drives

are a series of ultra-slim fast light weight 1.8 inch Winchester disk drive. The drives are

ATA-6 compliant.

SPECIFICATIONS MK4009GAL MK8009GAH

HDD1622 HDD1584

FORMATTED CAPACITY 40.0GB 80.0GB

HEIGHT 5mm 8mm

WEIGHT 1.69oz (48g) 2.08oz (59g)

NO. OF DISKS (PLATTERS) 1 2

NO. OF DATA HEADS 2 4

FUNCTIONAL SPECIFICATION

LOGICAL DRIVE MK4009GAL MK8009GAH

PARAMETERS HDD1622 HDD1584

NO. OF CYLINDERS (user) 62,640 62,640

BYTES PER SECTOR 512 512

BUFFER SIZE 8MB 2/8MB

ROTATION SPEED (±0.1%) 4,200rpm

TRANSFER RATE INTERNAL 165.0 - 356.8 Mbits/sec.

NO. OF CYLINDERS (logical) 16,383

NO. OF HEADS (logical) 1 6

NO. OF SECTORS/TRACK 6 3

HOST TRANSFER RATE

PIO/ULTRA DMA (ATA mode) 16.6/100MB/s

SEEK TIME

AVERAGE 15ms

TRACK-TO-TRACK 3ms

MAXIMUM 26ms

TEMPERATURE

OPERATING 41°F - 140°F (5°C - 60°C)

NON-OPERATING -4°F - 149°F (-20°C - 65°C)

HUMIDITY

OPERATING/NON-OPERATING 8 - 90% R.H. (No condensation)

SHIPPING 5 - 90% R.H. (No condensation)

WET BULB 29°C(operating)/40°C(non-operating)

CONNECTOR CABLING INFORMATION

The following table describes all of the pins on the Task File Interface:

PIN SIGNALS PIN SIGNALS

1 RESERVED 2 RESERVED

3 - RESET 4 GROUND

5 DD7 6 DD8

7 DD6 8 DD9

9 DD5 10 DD10

11 DD4 12 DD11

13 DD3 14 DD12

15 DD2 16 DD13

17 DD1 18 DD14

19 DD0 20 DD15

21 GROUND 22 DMARQ

23 GROUND 24 - DI0W

STOP

25 -DIOR 26 GROUND

-HDMARDY

HSTROBE

27 IORDY 28 GROUND

-DMARDY

DSTROBE

29 DMACK 30 INTRQ

31 DA1 32 - PDIAG/-CBLID

33 DA0 34 DA2

35 -CS0 36 -CS1

3 7 - DASP 3 8 +3.3V

39 +3.3V 40 RESERVED

Note: “-“ in front of signal name indicates negative logic.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Almacenamiento de Toshiba

Toshiba

Toshiba Q300 Series Manual de usuario

Toshiba

Toshiba TR200 Manual de usuario

Toshiba

Toshiba MK6022GAX Manual de usuario

Toshiba

Toshiba STOR.E ALU 2 Manual de usuario

Toshiba

Toshiba STORE alu Manual de usuario

Toshiba

Toshiba CANVIO Manual de usuario

Toshiba

Toshiba MK1517GAP Guía de inicio rápido

Toshiba

Toshiba (HDD2188) Manual de usuario

Toshiba

Toshiba CANVIO BASICS Manual de usuario

Toshiba

Toshiba GR 200 Series Manual de usuario

Toshiba

Toshiba MK5065GSX Guía de configuración

Toshiba

Toshiba HDDR160E03X Manual de usuario

Toshiba

Toshiba MK1633GSG Guía de configuración

Toshiba

Toshiba MK4026GAX Manual de usuario

Toshiba

Toshiba HDD1488 Manual de usuario

Toshiba

Toshiba Canvio AeroCast Manual de usuario

Toshiba

Toshiba MKxx75GSX Guía de configuración

Toshiba

Toshiba CANVIO Manual de usuario

Toshiba

Toshiba MK8016GSG Guía de inicio rápido

Toshiba

Toshiba CANVIO ADVANCE Manual de usuario

Toshiba

Toshiba RemotEye ESS Manual de usuario

Toshiba

Toshiba HDD2A02 Manual de usuario

Toshiba

Toshiba MK2003GAH Manual de usuario

Toshiba

Toshiba MK6022GAX Guía de inicio rápido

Manuales populares de Almacenamiento de otras marcas

QNAP

QNAP TS 32PXU Series Manual de usuario

LaCie

LaCie RUGGED RAID Manual de usuario

Freecom

Freecom CLS DOCK Manual de usuario

PNY

PNY Attache P-FD64MBATT3 Manual de usuario

HP StorageWorks MSL2024 Manual de usuario

OLT

OLT 6x6 Maximizer Manual de usuario

Transcend

Transcend JetFlash 160 Manual de usuario

LaCie

LaCie RUGGED MINI Manual de usuario

Thunderbolt

Thunderbolt 600 Manual de usuario

Panasonic

Panasonic LB-DH8 series Manual

Intel

Intel RAID High Availability Manual de usuario

LaCie

LaCie 12big Thunderbolt 3 Manual de usuario

Spectra Logic

Spectra Logic T-Series Spectra T50e Manual de usuario

Panasonic

Panasonic LKM-F931-1 Manual de usuario

Tabernus

Tabernus Enterprise Erase E2400 Manual de usuario

Rocstor

Rocstor COMMANDER 3F series Manual de usuario

HP P9000 Manual de usuario

Western Digital

Western Digital Ultrastar Data60 Manual de usuario