Toshiba TH450A-T Manual de usuario
STE 80870–0
TH450A-T
TH550A-T
THP550-T/TS3000
INSTRUCTION MANUAL
CEILING TYPE (OVERHEAD TRAVELING TYPE)
INDUSTRIAL ROBOT SPECIFICATIONS
Notice
1. Make sure that this instruction manual is delivered to the final
user of Toshiba Machine’s industrial robot.
2. Before operating the industrial robot, read through and
completely understand this manual.
3. After reading through this manual, keep it nearby for future
reference.
April 2010
TOSHIBA MACHINE CO., LTD.
NUMAZU, JAPAN
CEILING TYPE SPECIFICATIONS MANUAL
Copyright 2010 by Toshiba Machine Co., Ltd.
All rights reserved.
No part of this document may be reproduced in any form without obtaining prior written
permission from Toshiba Machine Co., Ltd.
The information contained in this manual is subject to change without prior notice to effect
improvements.
STE 80870
– 1 –
CEILING TYPE SPECIFICATIONS MANUAL
Preface
This manual describes the specifications of the TH450A, TH550A, THP550 ceiling type (or
overhead traveling type) industrial robot.
This manual is essential to keep the robot performance for a long time, to prevent failures
and to assure safety. Be sure to look through this manual and set up a maintenance
program before actually starting the robot.
Precautions on Safety
Important information on the robot and controller is noted in the instruction manual to
prevent injury to the user and persons nearby, prevent damage to assets and to ensure
correct use.
Make sure that the following details (indications and symbols) are well understood before
reading this manual. Always observe the information that is noted.
[Explanation of indications]
Indication Meaning of indication
!DANGER
This means that "incorrect handling will imminently
lead to fatalities or major injuries".
!WARNING
This means that "incorrect handling may lead to
fatalities or serious injuries."
!CAUTION
This means that "incorrect handling may lead to
personal injuries *1) or physical damage *2)".
*1) Injuries refer to injuries, burns and electric shocks, etc., which do not require
hospitalization or long term treatment.
*2) Physical damage refers to major fires due to destruction of assets or resources.
STE 80870
– 2 –
CEILING TYPE SPECIFICATIONS MANUAL
[Explanation of symbols]
Symbol Meaning of symbol
This means that the action is prohibited (must not be done).
Details of the actions actually prohibited are indicated with
pictures or words in or near the symbol.
This means that the action is mandatory (must be done).
Details of the actions that must be done are indicated with
pictures or words in or near the symbol.
This means danger and caution.
The details of the actual danger and caution are indicated with
pictures or words in or near the symbol.
[Maintenance and inspection]
Be sure to observe the following items to use this product safely.
!DANGER
Prohibited
• DO NOT incinerate, disassemble or charge the batteries.
Otherwise, they may rupture.
Mandatory
• Be sure to turn off the main power switch of the controller
before starting inspection or maintenance.
• Batteries should be disposed of according to the user's
in-house regulations.
STE 80870
– 3 –
CEILING TYPE SPECIFICATIONS MANUAL
!CAUTION
Disassembly
prohibited
• The user must NEVER replace or modify parts other than
those described in the instruction manual. Otherwise, the
performance may deteriorate or faults or accidents will be
caused.
Mandatory
• Always use the Toshiba Machine's designated spare parts
when replacing the parts.
• Maintenance and inspection should be performed regularly.
Otherwise, the system may malfunction or accidents will be
caused.
This manual is comprised of the following five (5) sections:
Section 1 Specifications
This section describes the basic specifications and names of respective parts
for the ceiling type (or overhead traveling type) industrial robot.
Section 2 Transportation
This section describes how to remove the ceiling type robot from its box and
how to transport it to the installation site. This section also deals with the
precautions to be taken when the robot is to be stored temporarily after
unpacked.
Section 3 Installation
This section discusses the ceiling type robot installation environment, space
requirements, and how to install the robot.
Section 4 Maintenance
This section describes the structure of the ceiling type robot and all items
required for the maintenance and inspection of the same robot.
Section 5 Replacement Parts for Maintenance
This section explains the replacement parts for the maintenance.
STE 80870
– 4 –
CEILING TYPE SPECIFICATIONS MANUAL
Table of Contents
Page
1. Specifications ...........................................................................................................6
1.1 Name of Each Part ..........................................................................................6
1.2 Outer Dimensions............................................................................................9
1.3 Specifications Table.......................................................................................15
2. Transportation ........................................................................................................19
2.1 Unpacking......................................................................................................19
2.2 Transportation ...............................................................................................19
2.2.1 Mass and Outer Dimensions.............................................................20
2.2.2 Transporting the Robot......................................................................22
2.3 Storage..........................................................................................................25
2.3.1 Storage Precautions for the Robot....................................................25
2.3.2 Storage Precautions for the Controller..............................................25
3. Installation ..............................................................................................................26
3.1 Installation Environment ................................................................................26
3.2 Installation Posture of the Robot....................................................................26
3.2.1 Coordinate System............................................................................27
3.2.2 Installing the Robot............................................................................29
3.2.3 Frame Rigidity...................................................................................32
4. Maintenance...........................................................................................................33
4.1 Layout of Robot Components........................................................................33
5. Replacement Parts for Maintenance.......................................................................35
5.1 Replacement Parts List for Maintenance.......................................................35
STE 80870
– 5 –
CEILING TYPE SPECIFICATIONS MANUAL
1. Specifications
1.1 Name of Each Part
The names of respective parts of the ceiling type (or overhead traveling type) robot are
shown in Figs. 1.1 to 1.3 below.
Cove
r
Base
Eyebolt
Brake OFF switch
Hand I/O connecto
r
A
rm 1
A
xis 1
(rotation)
Axis 2
(rotation)
Axis 4
(rotation)
A
rm 2
Ball screw spline
(tool shaft)
Axis 3
(vertical
movement)
Fig. 1.1 Name of each part (TH450A-T)
STE 80870
– 6 –
CEILING TYPE SPECIFICATIONS MANUAL
A
xis 2
(rotation)
Eyebolt
Brake OFF switch
Hand I/O connecto
r
A
rm 1
Axis 1
(rotation)
Axis 4
(rotation)
A
rm 2
Ball screw spline
(tool shaft)
Axis 3
(vertical
movement)
Fig. 1.2 Name of each part (TH550A-T)
STE 80870
– 7 –
CEILING TYPE SPECIFICATIONS MANUAL
A
xis 2
(rotation)
Eyebolt
Brake OFF switch
Hand I/O connecto
r
A
rm 1
Axis 1
(rotation)
Axis 4
(rotation)
A
rm 2
Ball screw spline
(tool shaft)
Axis 3
(vertical
movement)
Fig. 1.3 Name of each part (THP550-T)
STE 80870
– 8 –
CEILING TYPE SPECIFICATIONS MANUAL
1.2 Outer Dimensions
Figs. 1.4 to 1.9 show the outer dimensions of the ceiling type robot.
A
ir joint for hand for 4×φ4 tube
Optional Z-axis stroke
Standard
Z-axis stroke
Z-axis stroke 150 mm
Z-axis stroke 300 mm
Hand I/O connecto
r
Brake OFF switch 4
×
φ
14 mounting hole
(When Z-axis stroke is 300 mm)
Fig. 1.4 Outer dimensions of the robot (TH450A-T)
STE 80870
– 9 –
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Robótica de Toshiba
Toshiba
Toshiba THP550-IP Manual de usuario
Toshiba
Toshiba TCR Series Manual de usuario
Toshiba
Toshiba SR Series Manual de usuario
Toshiba
Toshiba TH650A-IP Manual de usuario
Toshiba
Toshiba THL Series Manual de usuario
Toshiba
Toshiba TVL Series Manual de usuario
Toshiba
Toshiba TH450A Manual de usuario
Toshiba
Toshiba THP700-IP Manual de usuario
Toshiba
Toshiba THL Series Manual de usuario
Toshiba
Toshiba TV800-CR Manual de usuario
Toshiba
Toshiba TH180 Manual de usuario
Toshiba
Toshiba TH Series Manual de usuario
Toshiba
Toshiba THP700 Manual de usuario
Toshiba
Toshiba TH850A Manual de usuario
Toshiba
Toshiba TH850A Manual de usuario
Toshiba
Toshiba TV1000H-WP Manual de usuario
Toshiba
Toshiba TV800 Manual de usuario
Toshiba
Toshiba TH650A Manual de usuario
Toshiba
Toshiba THP700 Manual de usuario
Toshiba
Toshiba TVL Series Manual de usuario
Manuales populares de Robótica de otras marcas
STEMCenter USA
STEMCenter USA Pi-Bot v2.00 Manual de usuario
SunFounder
SunFounder PiDog Manual de usuario
Universal Robots
Universal Robots UR5 Manual de usuario
Universal Robots
Universal Robots E Series Manual de usuario
YASKAWA
YASKAWA MOTOMAN-MPL80 II Manual de usuario
EFORT
EFORT ECR5 Manual de instrucciones
