Toshiba TDP-P6 Manual de usuario
USER’S GUIDE
TDP-P6
For assistance with your Toshiba projector in the
United States, please visit www.projectors.toshiba.com
or contact by phone at 800-829-8318.
For assistance with your Toshiba projector in Europe,
please visit www.toshiba-europe.com or contact your
local Toshiba dealer.
For assistance with your Toshiba projector in
Asia/Japan, please contact your local Toshiba dealer.
TDP-P6
Digital Projector
English Français Deutsch Español Japanese
TDPMT100.qxd 7/25/03 9:03 AM Page 1
English
3
Declaration of Conformity
Manufacturer: Toshiba Corporation
1-1, Shibaura 1-Chrome, Minato-ku, Tokyo, Japan
We declare under our sole responsibility that the TDP-P6 projector conform to the
following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
August, 2003
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is oper-
ated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
Agency Approvals
NOM, c-Tick, SJQA, IRAM
Other specific Country Approvals may apply, see please product certification label.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Remote Control Warning
Laser radiation class II product; wavelength 650nm; maximum output 1mW. Remote
control complies with applicable requirements of 21 CFR 1040.10 and 1040.11.
Remote control complies with applicable requirements of EN 60 825-1: 1994 +A11.
Do not look into the laser beam emitted
from the top of the remote control.
4
Table of Contents
Introduction 5
Connecting a computer 6
Required computer connections 6
Displaying a computer image 7
First-time projector use with Windows 98 8
Adjusting the image 10
Connecting a video device 11
Displaying a video image 12
Shutting down the projector 14
Troubleshooting your setup 14
Using the keypad buttons 22
Using the remote control 23
Using the audio 24
Optimizing computer images 25
Presentation features 25
Optimizing video images 26
Customizing the projector 26
Using the menus 27
Picture menu 28
Settings menu 31
Maintenance 34
Cleaning the lens 34
Replacing the projection lamp 35
Appendix 37
Accessories 37
For assistance with this projector 37
Red LED Behavior and Projector Errors 38
Projected image size 38
If you are experienced in setting up presentation systems, use the Quick Set
Up card that was included in the box. For complete details on connecting
and operating the projector, refer to this User’s Guide.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering that may
block the vents. Intake vents are placed along the left, front and back sides
of the projector. Exhaust vents are placed along the right side of the projec-
tor. In the unlikely event that the lamp ruptures, discard any edible items
and thoroughly clean the area along the right side of the projector.
2 ft (.6m)
Do not place objects in the area along the right side of the projector
5
Introduction
Your new digital projector packs great performance into a shape and size
customized for the mobile professional. It fits comfortably in your laptop
bag then transitions easily into your presentation environment. It is easy to
connect, easy to use, and easy to maintain.
Projector components and features
documentation
remote
computer
cable
projector
power
cable
audio cable adapter
audio cable
S-video cable
S-video to composite adapter
lens cap*
* the lens cap with tether ships in the accessory pouch. Insert the tether into the small
hole under the lens when you unpack your projector.
carry
case
keypad
connectors
elevator foot release
zoom
focus
lens cap
IR receiver
for remote
computer s-video
audio
power cord
6
Connecting a computer
Required computer connections
Connect the black end of the computer cable to the Computer in connector
on the projector. Connect the blue end to the video (VGA) port on your com-
puter. If you are using a desktop computer with a single VGA port, you first
need to disconnect the monitor from that computer’s video port.
Connect the black power cable to the connector on the side of the projector
and to your electrical outlet.
The Power LED on the projector’s keypad turns solid green and the fans
start to run.
NOTE: Always use the power cable that shipped with the projector.
Optional computer connections
To advance slides in a PowerPoint™ presentation using the remote, plug the
USB connector on the computer cable into the USB mouse connector on
your computer. USB drivers must be installed to use the USB feature. For
more information, see page 9.
To have sound with your presentation, connect the audio cable to your com-
puter and to the computer Audio In connector on the projector.
connect computer cable
connect power cable
connect USB portion of
computer cable
connect audio cable
7
Displaying a computer image
Remove the lens cap.
Press the Power button on the top of the projector.
The LED flashes green. When the lamp comes on, the startup screen is dis-
played and the LED is steady green. It can take a minute for the image to
achieve full brightness.
? No startup screen? Get help on page 15.
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Source button on the projector’s keypad.
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Refer to your computer’s documentation to learn the
activation commands specific for your computer. For example, some lap-
tops use a key combination of FN + F5 to turn the external display on and
off.
? No computer image? Try pressing the Auto Image
button on the keypad. Get help on page 16.
remove lens cap
press Power
turn on computer
source
activate laptop’s external port
8
First-time projector use with Windows 98
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wiz-
ard to load the correct driver (which was installed with your Windows
operating system).
If you are running Windows 2000, Windows ME, or Windows XP, skip these
steps and go to “Adjusting the image” on page 10.
aClick Next to begin searching for the driver.
bMake sure “Search for the best driver” is selected, then click Next.
cUncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
dWhen Windows finds the driver, you are ready to install it. Click Next.
a
b
c
d
9
Skip this page if you did not connect the USB portion of the computer
cable. The USB connection enables slide advance during presentations
and projector control software.
For Windows 98:
• If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.
•The Wizard launches three times.
The first time it detects a USB Composite Device.
The second time a USB Human Interface Device (for the keyboard).
The third time it detects a USB Human Interface Device (for the
mouse).
For Windows 2000, Windows ME, and Windows XP:
• The USB drivers are automatically installed.
10
Adjusting the image
Adjust the height of the projector, if necessary, by pressing the release but-
ton to extend the elevator foot.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
See page 38 for a table listing screen sizes and distances.
Adjust the zoom tab or the focus dial by rotating them until the desired
image size and sharpness are produced.
If the image is not square, adjust the keystone by using the buttons on the
keypad.
Press the upper Keystone button to reduce the upper part of the image, and
press the lower Keystone button to reduce the lower part.
Adjust the Contrast or Brightness in the Picture menu.
See page 27 for help with the menus.
adjust height
release button
adjust distance
adjust zoom and focus
focus
zoom
adjust keystone
adjust Contrast or Brightness
Otros manuales para TDP-P6
2
Tabla de contenidos
Otros manuales de Proyector de Toshiba
Toshiba
Toshiba TDP-MT700 Manual de usuario
Toshiba
Toshiba TLP-MT7 - LCD Projector - 1000 ANSI Lumens Manual de usuario
Toshiba
Toshiba TDP-T3 Manual de usuario
Toshiba
Toshiba TDP-T100U Manual de usuario
Toshiba
Toshiba TLP-X4500 Manual de usuario
Toshiba
Toshiba TDP-PX10 Manual de usuario
Toshiba
Toshiba TDP-PX10U - XGA DLP Projector Manual de usuario
Toshiba
Toshiba TLP-X150U Manual de operación y mantenimiento
Toshiba
Toshiba TDP-SP1U - SVGA DLP Projector Manual de usuario
Toshiba
Toshiba TLP X4100 Manual de usuario
Toshiba
Toshiba TDP-S25U Manual de usuario
Toshiba
Toshiba TLP-MT1 Manual de usuario
Toshiba
Toshiba TLP790 Manual de usuario
Toshiba
Toshiba TDP-T99U Manual de usuario
Toshiba
Toshiba t100 Manual de usuario
Toshiba
Toshiba TDP-T355 Manual de usuario
Toshiba
Toshiba TDP-SW25U Manual de usuario
Toshiba
Toshiba TDP-T40U Manual de usuario
Toshiba
Toshiba TDP TDP-T9 Manual de usuario
Toshiba
Toshiba TDP-TW100 Instrucciones de instalación
