Toshiba G3 Instrucciones de operación

G3 Applications

Workbook

G3 Applications Workbook

Industrial Division

13131 West Little York Road

Houston Texas 77041

Phone 800.231.1412 • Fax 713.896.5242

www.toshiba.com/ind

Table of Contents

Application Page

Programmable Monitoring 4

Binary Input 6

Pattern Run 8

Preset Speeds 11

Motor Operated Pot1 (MOP) 14

Motor Operated Pot2 (MOP) 15

Three Wire Control 17

Master-Follower 19

Programming the Input Terminals 21

Trim Pot 23

Speed Band Output 25

Adjustable Remote Torque Limit 26

Unblinded Groups Default 28

Bypass Control 29

Cyclic Overhauling Load 31

True Torque Control 35

Acc/Dec Time Switching Frequency 36

Direction Change with RX Input 37

Half Speed Command 39

Analog Outputs 40

Output Contacts 44

PID 48

Master/Follower: Pulse Output 56

Independent Dancer Control 59

Trim Dancer Control 62

120 Hz Constant Torque Operation of a 60 Hz Motor 65

Overspeed 67

Drooping 70

Carrier Frequency Derating 72

Load Sharing Application 74

Tosline F10 Communications With G3 Inverter and T2 PLC 76

Toshiba S20 Fiber Optics Communication 79

Changing the G3 LCD Display to German 86

Programmable Monitoring

The G3 has an extensive monitoring system which is employed via the keypad. The information

given in the monitor displays is useful while troubleshooting or commissioning applications.

Key Display Description

MOTOR RUN DIRECTION:

FORWARD Indicates direction associated with speed reference. Keypad direction reference

is separate from terminal strip direction reference.

MONITOR #1

MONITOR #2

PROGRAMMABLE

MONITOR #3 SEE BELOW

MONITOR #4

STATUS: R:-- S1:-- S2:--

S3:-- S4:-- S5:-- As these input terminals are shorted to CC, the “--” will change to “ON”. Use

this as a troubleshooting tool.

ST:ON F:-- RES:--

S6:-- S7:-- S8:-- As these input terminals are shorted to CC, the “--” will change to “ON”. Use

this as a troubleshooting tool. S6, S7, and S8 exist only on option card.

RCH:-- LOW:-- FLT:--

OUT:-- FAN:-- MC:ON As these output terminals close, the “--” will change to “ON”. Use this as a

troubleshooting tool. OUT exists only on option card. MC always says “ON”.

“FAN” shows “ON” when the drive’s muffin fan is on.

CUMULATIVE RUN TIME

0.00 .01 represents one hour. The timer is not resettable. An output contact can be

programmed to change state based on the CRT.

PAST TRIP #1

NO ERROR

PAST TRIP #2

NO ERROR The drive stores past faults; to clear these, put a “4” into Standard Setting Mode

Selection in the UTILITY PARAMETERS group.

PAST TRIP #3

NO ERROR

PAST TRIP #4

NO ERROR

MOTOR RUN DIRECTION:

FORWARD End/beginning of MONITOR mode

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

The following are the possible functions that can be assigned to the four programmable monitors

Value Description Comments

1 Drive compensated output frequency This will be greater than the commanded frequency.

2 Frequency reference This is not necessarily output frequency - drive may be stopped or accel/deceling

3 Output current (output current)2= (torque current)2 + (excitation current)2

4 Input voltage Drive gets from input VAC times 1.73 (will increase during regen).

5 Output voltage

6 Torque current (output current)2= (torque current)2 + (excitation current)2

7 Excitation current (output current)2= (torque current)2 + (excitation current)2

8 PID feedback value Displays the frequency the feedback signal represents

9 Motor OL ratio Example: G3 is rated 150% for 2 min. If you run at 150% for 1 minute, monitor will

10 Inverter OL ratio read “50%”. These monitors represent remaining overload capability. If any monitor

11 DBR OL ratio hits 100%, the drive trips. Drive OL warning starts when drive OL ratio hits 50%

12 Input power In KW

13 Output power In KW

14 RR terminal value Dependent on setting of “RR Input Special Function Select” (1)

15 Peak output current Reset by cycling power, pressing RUN, or resetting drive. Drive keeps track of both

16 Peak input voltage of these values even when not programmed to display as one of the four monitors.

Programming

The following example will make the monitors one through four frequency reference, torque

current, peak input voltage, and peak output current respectively.

Group Parameter New Value

UTILITY PARAMETERS Status Monitor #1 Display Select 2

UTILITY PARAMETERS Status Monitor #1 Display Select 6

UTILITY PARAMETERS Status Monitor #1 Display Select 16

UTILITY PARAMETERS Status Monitor #1 Display Select 15

If you want the current values to be displayed as amps, change Current Units Selection in the

UTILITY PARAMETERS group to “1”. If you want the voltage values to be displayed in percent,

change Voltage Units Selection in the UTILITY PARAMETERS group to a “0”.

(1)

Setting of RR Input Special

Function Select Comments

1 With 10 volts on ‘RR’ terminal, this monitor shows FH. Effective FH is

displayed as ‘RR’ input is changed. Zero volts on ‘RR’ makes effective

FH 30 Hz.

2 Displays acc/dec multiplier. Zero volts on ‘RR’ results in a display of

“1.0”. Ten volts on ‘RR’ results in a display of “10.0”.

3 Displays effective voltage boost. Zero volts on the ‘RR’ terminal results

in a “0.0” display. At ten volts, Voltage Boost is displayed

4 Displays effective Stall Protection Current Level. Minimum is 10%. A

bug: If Current Units Selection in UTILITY PARAMETERS is set to

show current in amps, no units will be displayed with the value in this

monitor.

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

Binary Input

Introduction

Among the many types of speed reference the G3 can accept is a binary coding. The binary code is based

upon the value of the programmed value of the Maximum Output Frequency (MOF) in the UTILITY

PARAMETERS group. A maximum of seven bits is available to code for the desired speed (ten with the option

board). The speed reference is a sum of digits whose value is the MOF divided by a power of two.

The following example allows a frequency setting resolution of 1 Hz when MOF is 64 Hz. Six bits will be

used. The Reset function will not be available in this scenario. F-CC and ST-CC must be hardwired on the

terminal strip to run.

Terminals S1, S2, S3, S4, RES, and R are assigned the functions of binary bits 10 through 5 respectively.

Binary bits 10 through 5 have reference values of MOF/21, MOF/22, MOF/23, MOF/24, MOF/25, and MOF/26

respectively. In this example, these values are 32, 16, 8, 4, 2, and 1.

Connections

F CC ST

S1 S2 S3 S4 RES R CC

Example of input combinations and corresponding drive outputs with MOF = 64 Hz

S1-CC (32) S2-CC (16) S3-CC (8) S4-CC (4) RES-CC (2) R-CC (1) Frequency Command

closed open open open open open 32

open closed open open closed closed 16+2+1 = 19

closed open open closed open closed 32+16+2 = 50

closed closed closed closed open open 32+16+8+4= 60

open open closed closed open open 8+4 = 12

Notes:

Be careful to connect to “R” and not to “RR”.

You may want to set an unused terminal’s function to “42” (binary data write) to store the frequency

command in the drive’s RAM. The drive will keep running at the speed commanded when the binary

data write was given (i.e. the terminal was shorted to CC) even though the contact closures that coded

for the reference may change.This RAM-written reference is lost when the drive is powered down.

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

Programming Group Parameter New Value

UTILITY PARAMETERS Blind Function Selection 1

UTILITY PARAMETERS Terminal Selection Parameters Blind 1

UTILITY PARAMETERS Frequency Setting Parameters Blind 1

TERMINAL SELECTION PARAMETERS Input Terminal Selection 1

TERMINAL SELECTION PARAMETERS “R” Input Terminal Function 27

TERMINAL SELECTION PARAMETERS “S1” Input Terminal Function 32

TERMINAL SELECTION PARAMETERS “S2” Input Terminal Function 31

TERMINAL SELECTION PARAMETERS “S3” Input Terminal Function 30

TERMINAL SELECTION PARAMETERS “S4” Input Terminal Function 29

TERMINAL SELECTION PARAMETERS “RES” Input Terminal Function 28

FREQUENCY SETTING PARAMETERS Frequency Priority Selection #1 5

FUNDAMENTAL PARAMETERS #1 Maximum Output Frequency 64

If you need more terminals (for more bits and more accuracy), see Potential Terminal Function in the

TERMINAL SELECTION PARAMETERS group and Guideline 10, Programming the Input Terminals.

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

Pattern Run

Introduction

Like the G2/G2+, the G3 has a Pattern Run feature. Pattern Run allows the user to associate a time, direction,

accel/decel time, and volts/hertz pattern with each preset speed. Any seven of the fifteen preset speeds can be

strung together to create a pattern; the G3 stores four such patterns. The number of times a pattern repeats is

programmable from one to infinity.

Pattern Run Diagram

Forward

Speed 2 time = 6 sec

30 Hz ACC2 used

DEC1 used

15 Hz

Speed 1

time =

3 sec

time

11 Hz Speed 3

time = time =

ACC1 used change in HZ / 3 sec

Max Out Freq * ACC2

= 15/80*30 = 5.625sec

Reverse time=41/80*5 = 2.56 sec

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

This programming example runs the above pattern twice

Group Parameter Value

UTILITY PARAMETERS Blind Function Selection 1

UTILITY PARAMETERS Frequency Setting Parameters Blind 1

UTILITY PARAMETERS Fundamental Parameters #2 Blind 1

UTILITY PARAMETERS Pattern Run Control Parameters Blind 1

FREQUENCY SETTING PARAMETERS Preset Speed Selection 3

FREQUENCY SETTING PARAMETERS Preset Speed Mode Activation 1*

FREQUENCY SETTING PARAMETERS Preset Speed #1 Frequency 15

FREQUENCY SETTING PARAMETERS Preset Speed #1 Operating Mode 0

FREQUENCY SETTING PARAMETERS Preset Speed #2 Frequency 30

FREQUENCY SETTING PARAMETERS Preset Speed #2 Operating Mode 2

FREQUENCY SETTING PARAMETERS Preset Speed #3 Frequency 11

FREQUENCY SETTING PARAMETERS Preset Speed #3 Operating Mode 1

PATTERN RUN CONTROL PARAMETERS Pattern Run Selection 1

PATTERN RUN CONTROL PARAMETERS Pattern Run Continue Mode 0

PATTERN RUN CONTROL PARAMETERS Pattern Group #1 Speed #1 1

PATTERN RUN CONTROL PARAMETERS Pattern Group #1 Speed #2 2

PATTERN RUN CONTROL PARAMETERS Pattern Group #1 Speed #3 3

PATTERN RUN CONTROL PARAMETERS Pattern Group #1 Number Of Cycles 2

PATTERN RUN CONTROL PARAMETERS Speed #1 Continue Mode 2**

PATTERN RUN CONTROL PARAMETERS Speed #1 Drive Time 3

PATTERN RUN CONTROL PARAMETERS Speed #2 Continue Mode 2**

PATTERN RUN CONTROL PARAMETERS Speed #2 Drive Time 6

PATTERN RUN CONTROL PARAMETERS Speed #3 Continue Mode 2**

PATTERN RUN CONTROL PARAMETERS Speed #3 Drive Time 3

FUNDAMENTAL PARAMETERS #1 Acceleration Time #1 5

FUNDAMENTAL PARAMETERS #1 Deceleration Time #1 5

FUNDAMENTAL PARAMETERS #2 Acceleration Time #2 30

FUNDAMENTAL PARAMETERS #2 Deceleration Time #2 30

To run from the keypad, make sure the LOCAL/REMOTE LED is on, then press RUN.

Hit the STOP button after completion to stop blinking LED and allow Pattern Run to be started again.

To run from the terminal strip, program the following...

Group Parameter Value

UTILITY PARAMETERS Blind Function Selection 1

UTILITY PARAMETERS Terminal Selection Parameters Blind 1

TERMINAL SELECTION PARAMETERS Input Terminal Selection 1

TERMINAL SELECTION PARAMETERS “S1” Input Terminal Function 14

...make sure the LOCAL/REMOTE LED is off, ‘F’-’CC’ or ‘R’-’CC’ is made, and close ‘S1’ to ‘CC’.

*For additional assistance, please contact Toshiba Adjustable Speed Drive Marketing Dept. at (800) 872-

2192

The drive can store programming for four different pattern runs - each can be remotely run by

programming an input terminal’s function (TERMINAL SELECTION PARAMETERS group) with a

value of 14 (for Pattern Run #1), 15 (for Pattern Run #2), 16 (for Pattern Run #3), or 17 (for Pattern Run

#4).

With normal programming, when a STOP command is given (i.e. ‘F’-’CC’ or ‘R’-’CC’ is opened or

STOP is pressed on the keypad) and the RUN command is remade (i.e. ‘F’-’CC’ or ‘R’-’CC’ is remade or

the RUN button is pressed), the Pattern Run starts over with the first speed. If an input terminal’s function

is programmed to “Pattern Run continue signal” (see value 18 in Guideline 10, Input Terminals), and this

terminal is shorted to ‘CC’, the drive resumes the pattern run at the speed after the speed at which it was

running when the STOP was given. Note: opening and reclosing ‘ST’-’CC’ is not considered a

STOP/RUN command in this scenario; the pattern’s clock keeps ticking. The continue signal must be

active when the pattern is started for correct Continue operation.

Speed #0 in any pattern is only run on the initial pass of the pattern (repeats of pattern don’t include Speed

#0) Press the MON button during the run to see the special information displayed during Pattern Run.

* If Preset Speed Mode Activation is set to “0”, the drive ignores direction, accel/decel times, and V/Hz

programmed into Preset Speed n Operating Mode and looks for direction and/or ACC/DEC and/or V/Hz

from terminal strip.

** With this parameter set to “5” and an input terminal’s function set to “19” (“Pattern Run step signal” ;

see Guideline 10, Input Terminals), the drive steps through the pattern’s speeds every time a momentary

contact closure is made to ‘CC’. Any programmed speed time is ignored.

Tabla de contenidos

Otros manuales de Instrumento de medición de Toshiba

Toshiba

Toshiba LF516 Manual de usuario

Toshiba

Toshiba Density (Consistency) Meter LQ500 Manual de usuario

Toshiba

Toshiba LF654 Manual de usuario

Toshiba

Toshiba LF470 Manual de usuario

Toshiba

Toshiba RemotEye 4 Manual de instrucciones

Toshiba

Toshiba GF630 Manual de usuario

Toshiba

Toshiba Sanitary Electromagnetic Flowmeter... Manual de usuario

Toshiba

Toshiba RD-97DTKB Manual de usuario

Toshiba

Toshiba LQ300A00 Series Manual de usuario

Toshiba

Toshiba LF232 Manual de usuario

Toshiba

Toshiba LF410 Manual de usuario

Toshiba

Toshiba Density (Consistency) Meter LQ500 Manual de usuario

Toshiba

Toshiba LF620F Manual de usuario

Toshiba

Toshiba LF434 Manual de usuario

Toshiba

Toshiba LF470 Manual de usuario

Toshiba

Toshiba LF810 Manual operacional

Toshiba

Toshiba Density (Consistency) Meter LQ500 Manual de usuario

Toshiba

Toshiba LF622 Manual de usuario

Toshiba

Toshiba LF620 B Series Manual de usuario

Toshiba

Toshiba PWU001Z-1 Manual de usuario

Toshiba

Toshiba GF642 Manual de usuario

Toshiba

Toshiba LF232*F Series Manual de usuario

Toshiba

Toshiba RBC-AIP3 Manual de usuario

Toshiba

Toshiba RBC-RD1-PE Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario