torras X002SF6B81 Manual de usuario
X002SF6B81
User Manual • Uživatelský manuál •
Užívateľský manuál • Használati utasítás •
Benutzerhandbuch
2
English
3 –11
Čeština
12 –20
Slovenčina
21 –29
Magyar
30 –38
Deutsch
39 –47
3
Dear customer,
Thank you for purchasing our product. Please read the following instructions carefully
before first use and keep this user manual for future reference. Pay particular attention
to the safety instructions. If you have any questions or comments about the device,
please contact the customer line.
✉www.alza.co.uk/kontakt
✆+44 (0)203 514 4411
Importer Alza.cz a.s., Jankovcova 1522/53, Holešovice, 170 00 Praha 7, www.alza.cz
4
Specifications
Product name:
Easy Clip Car Mount
Applicable places:
Windshield, Dashboard, Table, Air Vent
Package list:
Car Mount x 1
Suction Cup x 1
Dashboard Pad x 1
Air Vent Clip x 1
User Guide x 1
The parameters above are derived from the laboratory of TORRAS. The actual
parameters would be different because of products and other factors. The image shown
here is indicative only.
Product overview
Adjustable Feet
Silicone Pads
Quick Release Button
Clamp Arms
Ball joint
Screw Knob
Fixing Nut
Air Vent Clip
5
Installation steps
Method 1 –Using with the Suction Cup
Tips for using the Suction Cup
1. It will do not stick tightly when sticky the suction cup on the curved surface, plush
cloth surface or uneven surface.
2. It is not recommended to attach the suction cup to leathers, walls or film-coated
glass surfaces since the suction cup is designed with strong stickiness which may
cause surface damaged.
3. The suction would become weaker if the suction cup is frequently used at high or low
temperatures or in humid conditions. (Please avoid exposing it to the sun directly.)
4. Please take down the suction cup base and wash it with warn water if the suction of the
cup is not strong enough after a period use. It will be sticky again after drying naturally.
5. Please ensure the suction cup is covered by plastic wrap when the suction cup
holder was removed.
Ball joint
Telescopic Arm
Length Adjustment Knob
Angle Adjustment Knob
Suction Cup
Suction Cup Lock
Dashboard Pad
6
Tips for placing the Dashboard Pad
Before installing the mount on uneven or textured dashboard, please firstly stick the gel
pad on the dashboard (use only once). Tear off the red protective sticker of the pad,
stick it on the dashboard and press it firmly for over 30 seconds then let it rest for 1-3
days to reach high strong stickiness.
Clean
Press for 30 seconds
Wait for 1-3 days to use
Warm Tip:
Please wait for 24 hours to use after sticking the dashboard pad.
Stickiness reach 50 %
Stickiness reach 75 %
Stickiness reach 90 %
<1 hour
≥24 hours
≥72 hours
Car Mount assemble steps
1. Unscrew the retaining nut from the car mount and remove it.
2. Insert the ball joint into the retaining nut from the smaller opening side.
7
3. Push the ball joint firmly into the groove on the back of the car mount, then tighten
the fixing nut.
4. Clean the windshield or dashboard where you want to install the car mount with a
wet cloth, wait for it to dry.
5. If the installation position is not smooth enough, it is recommended to use the
dashboard pad in advance. Then install the suction cup on the pad, it would be more
stable. (If no need to use dashboard pad, please go to step 6 directly.)
6. Push the suction cup lock up to be fully open.
8
7. Tear off the transparent protective film of the suction cup. Then attach the suction cup
to the cleaning dashboard and press down the suction cup lock to secure the car mount.
8. Find the best view by adjusting the length and angle of the car mount to adapt to the
driving environment.
Method 2 –Using with the Twist-lock Air Vent Clip
1. Unscrew the retaining nut from the car mount and remove it.
2. Insert the ball joint into the retaining nut from the smaller side.
9
3. Push the ball joint firmly into the groove on the back of the car mount, then tighten
the fixing nut.
4. Twist the screw knob to adjust the opening size of the clip to fit the air vent.
5. Find a suitable place to insert the car mount. Tighten the screw knob to fix the car
mount. Adjust the angle of the car mount to fit your sight.
The suitability of car air vent
The air vent clip could be compatible with horizontal and vertical air vent outlets.
But it cannot support non-intensive, circular, or special-shaped air vent outlets.
Note: Please do not twist the air vent clip too tight, to protect the air vent blade and
air vent clip.
10
Using steps
1) Press the quick release button and the clamp arms automatically open. Then, put
your phone into the holder and pull the adjustable legs according to the size of your
phone to ensure that your phone is clamped securely.
2) Place your phone into the holder and press the clamp arms towards each other.
Then press the clamp arms with a little force again until you hear the “click”. Your
phone will be secured by the arm clamps.
Attentions
1. For your safety, do not install or adjust the mount while driving.
2. After using for a period of time, if the connection between the bracket and the vent
is loose, please tighten the screw knob again.
3. Do not knock, drop, or dismantle the product.
4. It is not recommended to disassemble the car mount frequently.
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios para automóviles de torras
