Toro 59226 Manual de usuario

Printed in USA

FORM NO. 3322–747

INSTALLATION

INSTRUCTIONS

MODEL NO. 59226

Mulching Kit

for 44” Side Discharge Mowers

Loose

Parts

Note: Use the chart below to verify all parts have been shipped.

DESCRIPTION QTY. USE

Blades 3

Replaces side discharge blades.

Baffle

Bolt, 5/16”–18 x 3/4”

Locknut, 5/16”–18

Mount baf

fles inside mower deck.

Pre–Installation

1. Remove mower unit (see Operator’s Manual for

instructions).

2. Thoroughly clean mower deck. All debris must

be removed to ensure baffle will fit properly

against mower deck.

3. Repair all bent or damaged areas of mower deck

and replace any missing parts.

4. Remove belt covers from mower deck.

5. Tip mower deck upside down and block up ends

to ease installation of mulcher components.

Removing

Existing Blades

1. Remove blades and anti-scalp cups from

spindles.

Note: Save blades and anti–scalp cups for use

when in side discharging mode.

POTENTIAL HAZARD

•Blade is sharp.

WHAT CAN HAPPEN

•Contact with sharp blade can cause serious

personal injury.

HOW TO AV

OID THE HAZARD

•Wear gloves or wrap sharp edges of the

blade with a rag.

Installation Instructions

Installing

Baffle

Note: There is one hole that is already drilled

for installing the baffle. This hole is

filled by a short bolt and nut. Remove

this nut and bolt and save for future

use (Fig. 1 and 2).



Figure 1

1 Baffle

2 Blade

(Sail faces deck)

Bolt Location in Baf

fle for

pre–drilled hole

4 Deck

5 Bolt

Lock Nut

Pre–drilled hole in deck

Hole to drill



Figure

1 Baffle..

2 Deck

3 Bolt

4 Lock

Nut

Hole to drill

Pre–drilled Hole

1. Place baffle in the cutting chamber (Fig. 2).

Note: When installing bolts, the bolt heads

need to be on the inside of cutting

deck.

2. Install a bolt and nut into the one pre–drilled

hole (Fig. 1 and 2).

Note: When installing bolt into pre–drilled

hole, notice which hole it is installed

through the baffle (Fig. 1).

3. Install new mulching blades after the baffle is in

place and without anti-scalp cups (Fig. 1).

IMPORTANT: The sail part of the blades

(i.e., the turned up section) must face the

inside of the mower (Fig. 1).

Installation Instructions

4. Tighten the blade mounting bolts to 85–110 ft-lb

(115–150 Nm).

5. To determine where you need to drill holes,

arrange the baffle in the mower as shown in

Figure 3. Rotate the center blade to ensure that

there is a 1/4” of clearance between the tip of the

center blade and the baffle.

Note: Use the center blade to determine the

location of the baffle.

M-4412

Figure 3

1 Center

Blade

2 Baffle 3

1/4” Clearance

6. Mark the location of the 3 remaining baffle

mounting holes (Fig. 2).

Note: There may be a slight gap on the

discharge side where the bracket meets

the deck.

7. Drill (3) 11/32” holes at the marked locations in

the mower.

8. Install and tighten all mounting hardware

securely (Fig. 1 and 2).

9. Rotate all the blades to ensure that there is at

least 1/4” clearance between the blades and

baffles.

POTENTIAL HAZARD

•A blade that is bent or damaged could

break apart and pieces could be thrown at

bystanders or at you as you use the mower.

WHAT CAN HAPPEN

•Pieces of blade that may be thrown could

seriously injure or kill you or bystanders.

HOW TO AV

OID THE HAZARD

•

Always r

eplace bent or damaged blade with

a new blade.

•Never file or create sharp notches in the

edges or surfaces of blade.

10. If the blades touch the baffle repeat the steps in

Installing Baffle section.

11. Make sure all holes in deck are plugged with a

nut and bolt.

POTENTIAL HAZARD

•Open holes in the mower exposes you and

others to thrown debris.

WHAT CAN HAPPEN

•Debris thrown out of holes in the mower

can cause injury.

HOW TO AV

OID THE HAZARD

•Never operate mower without hardware

mounted in all holes in mower.

•Install hardware in mounting holes when

mulching baffle is removed.

Reinstall Deck

1. Turn mower deck over, rightside up.

2. Install belt and belt covers onto mower deck.

3. Install mower unit (see Operator’s Manual for

instructions).

Installation Instructions

Mulching

ips

Selecting The Proper Height-Of-Cut Setting To

Suit Conditions – Remove approximately one inch

or no more that 1/3 of the grass blade when cutting.

In exceptionally lush and dense grass you may have

to raise the height-of-cut setting another notch or

convert to side discharge or bagging operations.

Mowing In Extreme Conditions – Air is required to

cut and recut grass clippings in mower housing, so do

not set height–of–cut too low or totally surround

housing by uncut grass. Always try to have one side

of the mower housing free from uncut grass, allowing

air to be drawn into housing. When making an initial

cut thru center of uncut area, operate machine slower

and back up if mower starts to clog.

Mow At Pr

oper Intervals

– Under most normal

conditions you’ll need to mow every 4–5 days.

However, grass grows at different rates at different

times. Thus, in order to maintain the same

height-of-cut, which is a good practice, you’ll need to

cut more frequently in early spring; as the grass

growth rate slows in mid summer, cut only every

8–10 days. If you are unable to mow for an extended

period due to weather conditions or other reasons,

convert to side discharge or bagging options or mow

first with the height-of-cut at a high level; then mow

again 2–3 days later with a lower height setting.

Always Mow With Sharp Blades – A sharp blade

cuts cleanly and without tearing or shredding the

grass blade like a dull blade. Tearing and shredding

causes the grass to turn brown at the edges which

impairs growth and increases susceptibility to

disease.

After Operating – To ensure optimum performance,

clean underside of mower housing after each use. If

residue is allowed to build up in mower housing

cutting performance will decrease.

Otros manuales de Accesorios para cortadoras de césped de Toro

Toro

Toro Greensmaster 04134 Manual de usuario

Toro

Toro 136-9125 Manual de usuario

Toro

Toro 127-6879 Manual de usuario

Toro

Toro 144-2688 Manual de usuario

Toro

Toro 144-1848 Manual de usuario

Toro

Toro 139-6040 Manual de usuario

Toro

Toro 02856 Manual de usuario

Toro

Toro GrandStand 133-1438 Manual de usuario

Toro

Toro 08781 Manual de usuario

Toro

Toro 08753 Manual de usuario

Toro

Toro Groundsmaster 360 Series Manual de usuario

Toro

Toro 144-0379 Manual de usuario

Toro

Toro 147-0090 Manual de usuario

Toro

Toro 136-1664 Manual de usuario

Toro

Toro CT Series Manual de usuario

Toro

Toro 120-3290 Manual de usuario

Toro

Toro 140-9324 Manual de usuario

Toro

Toro Groundsmaster e3200 Manual de usuario

Toro

Toro 04294 Manual de usuario

Toro

Toro TimeCutter 139-7478 Manual de usuario

Toro

Toro Reelmaster 2000 Series Manual de usuario

Toro

Toro 130-0105 Manual de usuario

Toro

Toro 72144 Guía de inicio rápido

Toro

Toro TransPro 80 series Manual de usuario

Manuales populares de Accesorios para cortadoras de césped de otras marcas

Ariens

Ariens 891008 Manual de usuario

Rover

Rover 108 - 109 Manual de usuario

Snapper

Snapper 1690047 Manual de usuario

Scag Power Equipment

Scag Power Equipment GC-F4 Manual de usuario

RHINO

RHINO 800 Manual de usuario

Exmark

Exmark Quest 126-7506 Manual de usuario

Snapper

Snapper 1685167 Manual de usuario

Cub Cadet

Cub Cadet 19B70029100 Manual de usuario

Stihl

Stihl AMK 043.1 Manual de usuario

MTD

MTD 753-0873 Manual

Bush Hog

Bush Hog RG60 Manual de usuario

Land Pride

Land Pride RCF2760 Manual de usuario

Simplicity

Simplicity 211 Manual de usuario

Exmark

Exmark ULTRAVAC QUICK DUMP SYSTEM Manual de usuario

Excel

Excel Two Bag Catcher Manual de usuario

Textron

Textron Jacobsen Pro12 DFS Manual de usuario

Ryobi

Ryobi AC018130 Manual de usuario

Snapper

Snapper 4544 Guía de configuración